Nathan Chordas-Ewell
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nathan Chordas-Ewell has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jun H. Choi
Department of Electrical Engineering, University at Buffalo, Buffalo, NY, USA
5 shared publications - Dongyin Ren
NXP Semiconductors, San Jose, CA, USA
3 shared publications - Kevin Xu
The State University of New York at Buffalo, Buffalo, NY, USA
2 shared publications - Ryan Wu
NXP Semiconductors, San Jose, CA, USA
2 shared publications - Zhi Li
Department of Electrical Engineering, University at Buffalo, Buffalo, NY, USA
2 shared publications Adly T. Fam
The State University of New York at Buffalo, Buffalo, NY, USA
1 shared publication
Latest Publications
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (5) , 761-764
Negative Resistance Enabled Amplifying CRLH Transmission Lines With Uniform Insertion Gain
A design method for amplifying composite right/left-handed (CRLH) transmission lines using negative resistance reflection amplifiers is presented in this letter. The introduction of the negative resistance in the shunt branch amplifies the traveling wave while maintaining the bidirectionality and the dispersion characteristics of the CRLH transmission line. Design methodology and calculation are backed up with full-wave simulation and measurement of a negative resistance enabled amplifying CRLH transmission line.
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (5) , 761-764
Negative Resistance Enabled Amplifying CRLH Transmission Lines With Uniform Insertion Gain
A design method for amplifying composite right/left-handed (CRLH) transmission lines using negative resistance reflection amplifiers is presented in this letter. The introduction of the negative resistance in the shunt branch amplifies the traveling wave while maintaining the bidirectionality and the dispersion characteristics of the CRLH transmission line. Design methodology and calculation are backed up with full-wave simulation and measurement of a negative resistance enabled amplifying CRLH transmission line.
- 16 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (12) , 10135-10147
A W-Band Frequency-Scanning Leaky Wave Antenna Based on a Composite Right/Left-Handed Waveguide for Rapid Beam Scanning
This paper presents a W-band (75-110 GHz) frequency-scanning leaky-wave antenna with backward-to-forward rapid beam-scanning capability. The design takes advantage of the low-loss and high-dispersion features of an air-filled composite right/left-handed metallic waveguide. Equivalent circuit modeling and a detailed design procedure are presented to facilitate the analysis and design. The design method is validated by a prototype antenna using 3D printing technology. Measurement results are consistent with simulated ones and show a wide field-of-view (FoV) from -15° to +35° when the radiated frequency is swept from 75.4GHz to 79.4GHz, equivalent to a high scanning rate of 9.68°/%BW. In simulation, when operated from 76.5GHz to 81.5GHz, the FoV can cover from -30° to +50°, which translates to a scanning rate of 12.64°/%BW. To the best of the authors’ knowledge, the presented antenna achieves the highest scanning rate in the W-band. The presented design may be a good candidate for millimeter-wave imaging applications that require low loss and rapid beam-scanning, including automotive radars.
- 16 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (12) , 10135-10147
A W-Band Frequency-Scanning Leaky Wave Antenna Based on a Composite Right/Left-Handed Waveguide for Rapid Beam Scanning
This paper presents a W-band (75-110 GHz) frequency-scanning leaky-wave antenna with backward-to-forward rapid beam-scanning capability. The design takes advantage of the low-loss and high-dispersion features of an air-filled composite right/left-handed metallic waveguide. Equivalent circuit modeling and a detailed design procedure are presented to facilitate the analysis and design. The design method is validated by a prototype antenna using 3D printing technology. Measurement results are consistent with simulated ones and show a wide field-of-view (FoV) from -15° to +35° when the radiated frequency is swept from 75.4GHz to 79.4GHz, equivalent to a high scanning rate of 9.68°/%BW. In simulation, when operated from 76.5GHz to 81.5GHz, the FoV can cover from -30° to +50°, which translates to a scanning rate of 12.64°/%BW. To the best of the authors’ knowledge, the presented antenna achieves the highest scanning rate in the W-band. The presented design may be a good candidate for millimeter-wave imaging applications that require low loss and rapid beam-scanning, including automotive radars.
- 7 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 342-344
Stripline- Based W- Band Frequency Scanning Composite Right/Left-Handed Leaky-Wave Antenna with a Tapered Aperture for Narrow Beamwidth
A stripline-based composite right/left-handed (CRLH) leaky-wave antenna (LWA) with a tapered aperture is designed for an increased effective aperture size. Experimental results show that the CRLH LWA is able to scan from −33° to 25.5° by sweeping the frequency from 76.75 GHz to 83 GHz, with a half-nower heamwidth (HPRW) of less than 5°.
- 7 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 342-344
Stripline- Based W- Band Frequency Scanning Composite Right/Left-Handed Leaky-Wave Antenna with a Tapered Aperture for Narrow Beamwidth
A stripline-based composite right/left-handed (CRLH) leaky-wave antenna (LWA) with a tapered aperture is designed for an increased effective aperture size. Experimental results show that the CRLH LWA is able to scan from −33° to 25.5° by sweeping the frequency from 76.75 GHz to 83 GHz, with a half-nower heamwidth (HPRW) of less than 5°.
- 12 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 57-60
Via-Less Waveguide-to-Stripline Transition Using 2D Electromagnetic Bandgap Structure
A novel waveguide-to-stripline transition utilizing an electromagnetic bandgap (EBG) structure is presented. The proposed transition, which does not require vias or waveguide shorts, delivers a simpler implementation option and allows the stripline to be mounted directly to the flange of a waveguide. The EBG structure is added to suppress parallel plate mode propagation and to ensure the transition can maintain the desired performance when used with arbitrary board dimensions. A 1.0dB insertion loss from 10.6GHz to 11.5GHz and a 10dB return loss bandwidth of 8.1% are achieved and verified by measurement.
- 12 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 57-60
Via-Less Waveguide-to-Stripline Transition Using 2D Electromagnetic Bandgap Structure
A novel waveguide-to-stripline transition utilizing an electromagnetic bandgap (EBG) structure is presented. The proposed transition, which does not require vias or waveguide shorts, delivers a simpler implementation option and allows the stripline to be mounted directly to the flange of a waveguide. The EBG structure is added to suppress parallel plate mode propagation and to ensure the transition can maintain the desired performance when used with arbitrary board dimensions. A 1.0dB insertion loss from 10.6GHz to 11.5GHz and a 10dB return loss bandwidth of 8.1% are achieved and verified by measurement.
- 10 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 242-245
Vibrating Antenna Doppler Radar
This paper presents a new method of gaining spatial resolution in continuous wave (CW) Doppler radars by using a vibrating antenna. Resolution of direction finding, though conventionally controlled through beam steering or other circuitry, is decoupled from the antenna and front-end circuitry by vibrating the antenna in a controlled fashion. It is shown that vibrating an antenna results in an induced Doppler shift, whereby the return from each spatial angle has a different Doppler frequency. This allows for smaller aperture antennas or antenna arrays to be used in place of larger aperture antennas or antenna arrays, thereby reducing the overall system's size and complexity. As a proof of concept, a single vibrating antenna radar is designed, fabricated, and tested in order to verify the angle finding capability for a single, as well as multiple targets. This method may also be expanded into two-dimensional detection by integrating a vibrating one-dimensional array.
- 10 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 242-245
Vibrating Antenna Doppler Radar
This paper presents a new method of gaining spatial resolution in continuous wave (CW) Doppler radars by using a vibrating antenna. Resolution of direction finding, though conventionally controlled through beam steering or other circuitry, is decoupled from the antenna and front-end circuitry by vibrating the antenna in a controlled fashion. It is shown that vibrating an antenna results in an induced Doppler shift, whereby the return from each spatial angle has a different Doppler frequency. This allows for smaller aperture antennas or antenna arrays to be used in place of larger aperture antennas or antenna arrays, thereby reducing the overall system's size and complexity. As a proof of concept, a single vibrating antenna radar is designed, fabricated, and tested in order to verify the angle finding capability for a single, as well as multiple targets. This method may also be expanded into two-dimensional detection by integrating a vibrating one-dimensional array.