Ninda Hardina Batubara
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ninda Hardina Batubara has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
A Aryswan
Politeknik Negeri Batam
1 shared publicationH Butar Butar
Politeknik Negeri Batam
1 shared publication- Harus Laksana Guntur
Institut Teknologi Sepuluh Nopember, Indonesia
1 shared publication - Meschac Timothee Silalahi
Politeknik Negeri Batam
1 shared publication - Muhammad Hasan Albana
Department of Mechanical Engineering, Politeknik Negeri Batam, Batam 29461, Indonesia
1 shared publication - Novebriantika Novebriantika
Program Studi Teknologi Rekayasa Pengelasan dan Fabrikasi, Politeknik Negeri Batam
1 shared publication
Latest Publications
- Open Access
- 19 September 2025
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 16 (9) , 536
Investigation of Flow Channel Configurations in Liquid-Cooled Plates for Electric Vehicle Battery Thermal Management
Mitigating heat generation in electric vehicle (EV) batteries is crucial for safety, operational efficiency, and battery lifespan. Liquid-cooled cold plates are widely used; however, comparative studies of channel geometries are often hindered by inconsistent experimental conditions. This study systematically compares six cold plate configurations under identical cross-sectional areas and uniform thermal boundary conditions. These controls isolate the effect of geometry on performance. Computational fluid dynamics (CFDs) was used to evaluate six configurations, derived from three main channel layouts (serpentine with eight U-turns, serpentine with six U-turns, and elliptical) and two cross-sectional shapes (circular and square). The serpentine square-tube design with eight U-turns exhibited the lowest thermal resistance (0.0159 K/W). The circular-tube variant achieved the most uniform temperature distribution (TUI > 0.53). The six U-turn circular-tube configuration demonstrated the lowest pressure drop (11.7 kPa). The results indicate that no single design optimizes all performance metrics, highlighting trade-offs between cooling effectiveness, temperature uniformity, and hydraulic efficiency. By isolating geometric variables, this study offers targeted design recommendations for engineers developing battery thermal management systems (BTMS).
- 19 September 2025
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 16 (9) , 536
Open AccessInvestigation of Flow Channel Configurations in Liquid-Cooled Plates for Electric Vehicle Battery Thermal Management
Mitigating heat generation in electric vehicle (EV) batteries is crucial for safety, operational efficiency, and battery lifespan. Liquid-cooled cold plates are widely used; however, comparative studies of channel geometries are often hindered by inconsistent experimental conditions. This study systematically compares six cold plate configurations under identical cross-sectional areas and uniform thermal boundary conditions. These controls isolate the effect of geometry on performance. Computational fluid dynamics (CFDs) was used to evaluate six configurations, derived from three main channel layouts (serpentine with eight U-turns, serpentine with six U-turns, and elliptical) and two cross-sectional shapes (circular and square). The serpentine square-tube design with eight U-turns exhibited the lowest thermal resistance (0.0159 K/W). The circular-tube variant achieved the most uniform temperature distribution (TUI > 0.53). The six U-turn circular-tube configuration demonstrated the lowest pressure drop (11.7 kPa). The results indicate that no single design optimizes all performance metrics, highlighting trade-offs between cooling effectiveness, temperature uniformity, and hydraulic efficiency. By isolating geometric variables, this study offers targeted design recommendations for engineers developing battery thermal management systems (BTMS).
- Open Access
- 4 May 2023
- Published by Universitas Pahlawan Tuanku Tambusai in Jurnal Pendidikan Tambusai
- Vol. 7 (2) , 8063-8070
Uji Mekanik Material Pipa SA-312 TP304L untuk Kualifikasi PQR Sesuai ASME BPVC Sec. IX-2019
Sesuai ASME BPVC Sec.IX, Welding Procedure Specification (WPS) dinyatakan layak digunakan untuk proyek pengelasan dengan diikualifikasi dahulu menggunakan Procedure Qualified Record (PQR). Pengujian mekanikal dengan menimbulkan kerusakan untuk mengetahui ketahanan suatu material dengan cara ditekan, ditarik, dan dilengkungkan. Penelitian bertujuan mengetahui kualitas pengelasan dan rentang ketebalan material yang dapat dikualifikasi menggunakan test coupon pada PQR. Pengujian mekanikal yang dibutukan pada PQR ini yaitu dua spesimen tensile test dan empat spesimen bend test dengan acceptance criteria spesifikasi ASME BPVC Sec. IX-2019. Pada spesimen tensile test 1 dan 2, diketahui nilai ultimate tensile strength yaitu sebesar 584 MPa dan 594 MPa. Salah satu spesimen root bend pada bend test memiliki diskontinuitas terbuka di area weld sebesar 0.5 mm. Berdasarkan pada ASME BPVC Sec. IX-2019, nilai minimum yang diijinkan untuk tensile test pada material SA-312 TP304L yaitu sebesar 485 MPa, serta ukuran maksimum diskontinuitas terbuka yang diperbolehkan untuk bend test pada area weld dan HAZ, yaitu sebesar 3 mm.
- 4 May 2023
- Published by Universitas Pahlawan Tuanku Tambusai in Jurnal Pendidikan Tambusai
- Vol. 7 (2) , 8063-8070
Open AccessUji Mekanik Material Pipa SA-312 TP304L untuk Kualifikasi PQR Sesuai ASME BPVC Sec. IX-2019
Sesuai ASME BPVC Sec.IX, Welding Procedure Specification (WPS) dinyatakan layak digunakan untuk proyek pengelasan dengan diikualifikasi dahulu menggunakan Procedure Qualified Record (PQR). Pengujian mekanikal dengan menimbulkan kerusakan untuk mengetahui ketahanan suatu material dengan cara ditekan, ditarik, dan dilengkungkan. Penelitian bertujuan mengetahui kualitas pengelasan dan rentang ketebalan material yang dapat dikualifikasi menggunakan test coupon pada PQR. Pengujian mekanikal yang dibutukan pada PQR ini yaitu dua spesimen tensile test dan empat spesimen bend test dengan acceptance criteria spesifikasi ASME BPVC Sec. IX-2019. Pada spesimen tensile test 1 dan 2, diketahui nilai ultimate tensile strength yaitu sebesar 584 MPa dan 594 MPa. Salah satu spesimen root bend pada bend test memiliki diskontinuitas terbuka di area weld sebesar 0.5 mm. Berdasarkan pada ASME BPVC Sec. IX-2019, nilai minimum yang diijinkan untuk tensile test pada material SA-312 TP304L yaitu sebesar 485 MPa, serta ukuran maksimum diskontinuitas terbuka yang diperbolehkan untuk bend test pada area weld dan HAZ, yaitu sebesar 3 mm.