Kap Ryeol Ku
Research Subjects
Kap Ryeol Ku has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Jung Gyu Kim
Senic
4 shared publications - Jung Woo Choi
Senic
4 shared publications - Won-Jae Lee
School of Advanced Materials Engineering, Dong-Eui University, Busan 51140, Republic of Korea
4 shared publications - Chae Young Lee
Senic
3 shared publications - Jong Hwi Park
Senic
3 shared publications - Seung Jun Lee
Senic
3 shared publications
Latest Publications
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 393, 59-64
Optimization of Seed Crystal Stability at the Initial Growth Stage Depending on Heating Ramp Rates and Gas Flow Channels of SiC Source Powder for Growth of 8-inch N- Type 4H-SiC Single Crystal
Seed crystal stabilization during the initial stage of 200-mm 4H-SiC crystal growth is critical for achieving high-quality wafers with large diameters. This study investigated the effects of heating ramp rates (0 - 6 °C/min) and SiC source powder porosity through both simulation and experimental approaches. Low ramp rates resulted in surface degradation of the seed crystal, whereas high ramp rates induced significant thermal stress, leading to cracking. Optimal ramp rates of 3 - 5 °C/min significantly minimized damage caused by seed crystal loss. Furthermore, high-porosity source powder facilitated adequate gas transport channels, thereby enhancing seed crystal stability. Crystals grown under these optimized conditions demonstrated improved edge morphology, absence of polycrystalline inclusions, and low dislocation densities, with threading screw dislocations (TSD) below 500 cm -2 and basal plane dislocations (BPD) below 1,000 cm -2 . These results demonstrate that precise control of thermal parameters and source powder porosity offers an effective strategy for stable seed attachment and reproducible growth of high-quality, large-diameter SiC single crystals.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 393, 59-64
Open AccessOptimization of Seed Crystal Stability at the Initial Growth Stage Depending on Heating Ramp Rates and Gas Flow Channels of SiC Source Powder for Growth of 8-inch N- Type 4H-SiC Single Crystal
Seed crystal stabilization during the initial stage of 200-mm 4H-SiC crystal growth is critical for achieving high-quality wafers with large diameters. This study investigated the effects of heating ramp rates (0 - 6 °C/min) and SiC source powder porosity through both simulation and experimental approaches. Low ramp rates resulted in surface degradation of the seed crystal, whereas high ramp rates induced significant thermal stress, leading to cracking. Optimal ramp rates of 3 - 5 °C/min significantly minimized damage caused by seed crystal loss. Furthermore, high-porosity source powder facilitated adequate gas transport channels, thereby enhancing seed crystal stability. Crystals grown under these optimized conditions demonstrated improved edge morphology, absence of polycrystalline inclusions, and low dislocation densities, with threading screw dislocations (TSD) below 500 cm -2 and basal plane dislocations (BPD) below 1,000 cm -2 . These results demonstrate that precise control of thermal parameters and source powder porosity offers an effective strategy for stable seed attachment and reproducible growth of high-quality, large-diameter SiC single crystals.
- Open Access
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1157, 75-79
High-Quality SiC Crystal Growth by Cooldown Rate Control at Cooling Stage
Thermoelastic stress generated within SiC crystals during the cooling process can induce various types of dislocation defects. In this study, a newly designed cooling protocol was proposed to investigate the correlation between cooldown rate and defect formation in 4H-SiC single crystals. Three distinct cooldown rates, 10~30 °C/min, 1~5 °C/min, and less than 1 °C/min, were applied to assess their impact on the development of thermoelastic stress and resulting crystal quality. Notable variations in ingot color and surface morphology were observed depending on the applied cooldown rate. Dislocation types, including basal plane dislocations (BPDs), threading edge dislocations (TEDs), and threading screw dislocations (TSDs), were quantified through etch pit density (EPD) measurements after molten KOH etching at 600 °C for 14 minutes. The results indicate that higher cooldown rates led to an increase in BPD density due to enhanced plastic deformation, while lower cooldown rates resulted in higher TED and TSD densities, likely due to increased thermal stress. These findings demonstrate that precise control of the cooldown rate is critical for suppressing thermoelastic stress and minimizing defect densities in SiC crystal growth.
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1157, 75-79
Open AccessHigh-Quality SiC Crystal Growth by Cooldown Rate Control at Cooling Stage
Thermoelastic stress generated within SiC crystals during the cooling process can induce various types of dislocation defects. In this study, a newly designed cooling protocol was proposed to investigate the correlation between cooldown rate and defect formation in 4H-SiC single crystals. Three distinct cooldown rates, 10~30 °C/min, 1~5 °C/min, and less than 1 °C/min, were applied to assess their impact on the development of thermoelastic stress and resulting crystal quality. Notable variations in ingot color and surface morphology were observed depending on the applied cooldown rate. Dislocation types, including basal plane dislocations (BPDs), threading edge dislocations (TEDs), and threading screw dislocations (TSDs), were quantified through etch pit density (EPD) measurements after molten KOH etching at 600 °C for 14 minutes. The results indicate that higher cooldown rates led to an increase in BPD density due to enhanced plastic deformation, while lower cooldown rates resulted in higher TED and TSD densities, likely due to increased thermal stress. These findings demonstrate that precise control of the cooldown rate is critical for suppressing thermoelastic stress and minimizing defect densities in SiC crystal growth.
- Open Access
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1157, 69-73
Optimization of Heat Transfer Design for High Quality 4H-SiC Ingot Growth
At the high growth temperatures of the PVT method, thermal radiation from the graphite crucible surface to the seed region is the dominant mode of heat transfer. In this study, we propose a newly designed crucible structure with a thinner graphite wall compared to the conventional design for SiC crystal growth. The SiC ingot grown using the conventional crucible exhibited the smallest thickness variation (flat top surface) between the center and the edge of the ingot, accompanied by polytype inclusions, which led to an increase in defect density. In contrast, SiC ingots grown using the newly designed crucibles (Design A and Design B) showed a convex top surface and a significantly lower defect density due to the improved heat transfer efficiency. Thinning the graphite crucible wall helps maintain a relatively higher temperature at the seed edge region, thereby effectively enhancing thermal radiation in the radial direction inside the crucible. These results indicate that thermal radiation in the radial direction can be achieved through appropriate optimization of the graphite wall thickness.
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1157, 69-73
Open AccessOptimization of Heat Transfer Design for High Quality 4H-SiC Ingot Growth
At the high growth temperatures of the PVT method, thermal radiation from the graphite crucible surface to the seed region is the dominant mode of heat transfer. In this study, we propose a newly designed crucible structure with a thinner graphite wall compared to the conventional design for SiC crystal growth. The SiC ingot grown using the conventional crucible exhibited the smallest thickness variation (flat top surface) between the center and the edge of the ingot, accompanied by polytype inclusions, which led to an increase in defect density. In contrast, SiC ingots grown using the newly designed crucibles (Design A and Design B) showed a convex top surface and a significantly lower defect density due to the improved heat transfer efficiency. Thinning the graphite crucible wall helps maintain a relatively higher temperature at the seed edge region, thereby effectively enhancing thermal radiation in the radial direction inside the crucible. These results indicate that thermal radiation in the radial direction can be achieved through appropriate optimization of the graphite wall thickness.
- Open Access
- 4 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1156, 43-48
Process Gas Control for High-Resistance HPSI-SiC Growth
In this study, we tried to grow SiC ingots with high resistivity and polytype stability with adoption hydrogen mixed gas flow to the PVT method. Three different types of growth atmosphere of N2+Ar, H/Ar ratio:10% and 30% were employed. The polytype inclusion, crystal shape and transparency, and their resistivity were systematically investigated by UVF images, exposing backlighting, and high resistivity analysis using COREMA (Contactless Resistivity Mapper), respectively. The SiC ingot grown with adoption N2+Ar exhibited a suppression of polytype inclusion, a convex shape and a lower resistivity. In contrast, the SiC ingot with more higher H/Ar ratio of 30% than that of 10% shows no polytype inclusion and highest resistivity of 1.7E11mΩ∙cm. The growth atmosphere of relative higher H/Ar ratio in SiC crystal growth could be led the way to manufacture HPSI (high-purity semi-insulating)-SiC single crystal with polytype stability.
- 4 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1156, 43-48
Open AccessProcess Gas Control for High-Resistance HPSI-SiC Growth
In this study, we tried to grow SiC ingots with high resistivity and polytype stability with adoption hydrogen mixed gas flow to the PVT method. Three different types of growth atmosphere of N2+Ar, H/Ar ratio:10% and 30% were employed. The polytype inclusion, crystal shape and transparency, and their resistivity were systematically investigated by UVF images, exposing backlighting, and high resistivity analysis using COREMA (Contactless Resistivity Mapper), respectively. The SiC ingot grown with adoption N2+Ar exhibited a suppression of polytype inclusion, a convex shape and a lower resistivity. In contrast, the SiC ingot with more higher H/Ar ratio of 30% than that of 10% shows no polytype inclusion and highest resistivity of 1.7E11mΩ∙cm. The growth atmosphere of relative higher H/Ar ratio in SiC crystal growth could be led the way to manufacture HPSI (high-purity semi-insulating)-SiC single crystal with polytype stability.