Shunya Hirano
Research Subjects
Research Interests
Shunya Hirano has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Noboru Ohtani
Kwansei Gakuin University
2 shared publications - Shuzo Masui
The University of Tokyo
2 shared publications - Hyuk Kim
Engineering Development Group of LASER Business Division
1 shared publication - Kozo Abe
Kwansei Gakuin University
1 shared publication - Kozo Abe
Kwansei Gakuin University, School of Engineering
1 shared publication - Masaki Michihata
The University of Tokyo
1 shared publication
Latest Publications
- Open Access
- 21 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1193, 77-82
BPD-Free Dicing of Epitaxial SiC Wafers Using Water Jet Guided Laser
Silicon carbide (SiC) wafers are essential for next-generation power devices, however conventional dicing methods often induce cracks and Basal Plane Dislocations (BPDs), reducing device reliability. This study demonstrates BPD-free dicing of epitaxial SiC wafers using Water jet Guided Laser (WGL) processing. Full-thickness cutting was performed on 350 μm-thickness wafers with a 10 μm-thickness epitaxial layer using a YAG laser (532 nm wavelength, 200 ns pulse width, 10 kHz repetition rate, 30–80 W output) on an LB300 system. BPD evaluation was carried out by X-ray topography (XRT) with the-1-128 reflection before and after cutting. The results showed no generation or propagation of new BPDs, and pre-existing BPDs did not glide, confirming that WGL processing enables BPD-free machining. These results are attributed to the ablation-based nature of WGL with water assistance, which avoids mechanical stress on epitaxial SiC wafers.
- 21 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1193, 77-82
Open AccessBPD-Free Dicing of Epitaxial SiC Wafers Using Water Jet Guided Laser
Silicon carbide (SiC) wafers are essential for next-generation power devices, however conventional dicing methods often induce cracks and Basal Plane Dislocations (BPDs), reducing device reliability. This study demonstrates BPD-free dicing of epitaxial SiC wafers using Water jet Guided Laser (WGL) processing. Full-thickness cutting was performed on 350 μm-thickness wafers with a 10 μm-thickness epitaxial layer using a YAG laser (532 nm wavelength, 200 ns pulse width, 10 kHz repetition rate, 30–80 W output) on an LB300 system. BPD evaluation was carried out by X-ray topography (XRT) with the-1-128 reflection before and after cutting. The results showed no generation or propagation of new BPDs, and pre-existing BPDs did not glide, confirming that WGL processing enables BPD-free machining. These results are attributed to the ablation-based nature of WGL with water assistance, which avoids mechanical stress on epitaxial SiC wafers.
- Open Access
- 9 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1159, 55-59
Damage Evaluation and Elemental Analysis of SiC Wafers Processed by Water Jet Guided Laser
Low-process damage dicing technologies are required to improve the reliability of silicon carbide (SiC) devices. Existing methods, such as ultrasonic diamond blade dicing, dry laser dicing, and stealth dicing, introduce mechanical or thermal stresses that lead to cracks and dislocations, including basal plane dislocations (BPDs), which degrade device quality. In this study, we assess the crystalline defects induced by water jet guided laser (WGL) processing on a SiC wafer using X-ray topography (XRT) and investigate the underlying processing mechanisms through Energy Dispersive X-ray Spectroscopy (EDX). The asymmetric contrast observed along the processed grooves in the XRT images was due to the X-ray irradiation direction, and no significant BPD formation was observed. The EDX results showed that the processed surface was oxidized by laser ablation. Thus, WGL processing can provide damage-free dicing of SiC wafers with minimal mechanical stress and defects.
- 9 September 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1159, 55-59
Open AccessDamage Evaluation and Elemental Analysis of SiC Wafers Processed by Water Jet Guided Laser
Low-process damage dicing technologies are required to improve the reliability of silicon carbide (SiC) devices. Existing methods, such as ultrasonic diamond blade dicing, dry laser dicing, and stealth dicing, introduce mechanical or thermal stresses that lead to cracks and dislocations, including basal plane dislocations (BPDs), which degrade device quality. In this study, we assess the crystalline defects induced by water jet guided laser (WGL) processing on a SiC wafer using X-ray topography (XRT) and investigate the underlying processing mechanisms through Energy Dispersive X-ray Spectroscopy (EDX). The asymmetric contrast observed along the processed grooves in the XRT images was due to the X-ray irradiation direction, and no significant BPD formation was observed. The EDX results showed that the processed surface was oxidized by laser ablation. Thus, WGL processing can provide damage-free dicing of SiC wafers with minimal mechanical stress and defects.