Yuankai Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yuankai Ren has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Hangyu Lu
Institute of Intelligent Vehicles, Shanghai Jiao Tong University, Shanghai, China
3 shared publications - Jianwei Lu
School of Automotive and Transportation Engineering, Hefei University of Technology, China
3 shared publications - Dinghua Zhou
School of Automotive and Transportation Engineering, Hefei University of Technology , Hefei, Anhui 230000, China
2 shared publications - Gaoming Deng
School of Automotive and Transportation Engineering, Hefei University of Technology , Hefei, Anhui 230000, China
2 shared publications - Ning Zhang
School of Mechanical Engineering, Southeast University, Nanjing 211189, China
2 shared publications - Bofu Wu
School of Automobile and Transportation Engineering, Hefei Univerisity of Technology , Hefei, Anhui 230009, China
1 shared publication
Latest Publications
- 11 March 2026
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 114 (5) , 387
Going beyond the limit: use the unexploited domain of maneuverability to negotiate safe vehicle cornering
- 11 March 2026
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 114 (5) , 387
Going beyond the limit: use the unexploited domain of maneuverability to negotiate safe vehicle cornering
- 28 October 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (9) , 5990-6001
Load spectrum editing for automotive fasteners based on bolt critical load
The durability of threaded fasteners is critical to chassis reliability. Conventional load spectrum editing often retains low-amplitude, high-cycle loads that extend test time without affecting preload. This study introduces an accelerated editing method that integrates the bolt critical load threshold with the S-transform to account for the loosening mechanism of fasteners. Road load data were collected under representative driving conditions, and the proposed method was used to remove non-damaging segments while preserving fatigue-relevant features. Simulation results show that the edited spectrum significantly shortens test duration while maintaining consistency with the original in statistical parameters, spectral distribution, and fatigue damage. The method improves testing efficiency and provides practical value for automotive durability evaluation, product development, and quality assurance.
- 28 October 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (9) , 5990-6001
Load spectrum editing for automotive fasteners based on bolt critical load
The durability of threaded fasteners is critical to chassis reliability. Conventional load spectrum editing often retains low-amplitude, high-cycle loads that extend test time without affecting preload. This study introduces an accelerated editing method that integrates the bolt critical load threshold with the S-transform to account for the loosening mechanism of fasteners. Road load data were collected under representative driving conditions, and the proposed method was used to remove non-damaging segments while preserving fatigue-relevant features. Simulation results show that the edited spectrum significantly shortens test duration while maintaining consistency with the original in statistical parameters, spectral distribution, and fatigue damage. The method improves testing efficiency and provides practical value for automotive durability evaluation, product development, and quality assurance.
- Open Access
A New Hybrid Rigid–Flexible Coupling Modeling for Efficient Vibration Analysis of the Cooling System of New Energy Vehicles
The cooling system is a core component for a vehicle’s powertrains to operate smoothly and maintain a satisfying noise, vibration, and harshness (NVH) performance. However, advances in new energy vehicles bring with them complex requirements for the cooling fan design due to new issues such as increased heat load, dynamic variations, and high-speed vibrations, which demand the optimization of fan dynamics over a wide range of parameters. In this paper, by thoroughly checking the effect of rigid–flexible coupling and the geometrically complex elastic frame of the fan, we propose a combined modeling approach to reduce the computational time of broad-range parameter variation analysis and examine the vibration problem in the cooling fans under various external excitations. First, the complicated frame of the fan is simplified through virtual prototyping based on an experiment. Then, modal transition is applied, reducing the complex kinetic expression, and a time-invariant system model is derived with multi-blade coordinate transformation. Stability and bifurcation analysis are performed regarding different excitation couplings from the rotor, powertrain, and road. The results of the simulation and experiment illustrate that the proposed methodology achieves a substantial reduction in computational time, and all degrees of freedom (DOFs) are divided into two groups including symmetrical and asymmetrical types. The results also imply the great potential for the optimization and control of the high-speed fan’s vibration for new energy cars.
Open AccessA New Hybrid Rigid–Flexible Coupling Modeling for Efficient Vibration Analysis of the Cooling System of New Energy Vehicles
The cooling system is a core component for a vehicle’s powertrains to operate smoothly and maintain a satisfying noise, vibration, and harshness (NVH) performance. However, advances in new energy vehicles bring with them complex requirements for the cooling fan design due to new issues such as increased heat load, dynamic variations, and high-speed vibrations, which demand the optimization of fan dynamics over a wide range of parameters. In this paper, by thoroughly checking the effect of rigid–flexible coupling and the geometrically complex elastic frame of the fan, we propose a combined modeling approach to reduce the computational time of broad-range parameter variation analysis and examine the vibration problem in the cooling fans under various external excitations. First, the complicated frame of the fan is simplified through virtual prototyping based on an experiment. Then, modal transition is applied, reducing the complex kinetic expression, and a time-invariant system model is derived with multi-blade coordinate transformation. Stability and bifurcation analysis are performed regarding different excitation couplings from the rotor, powertrain, and road. The results of the simulation and experiment illustrate that the proposed methodology achieves a substantial reduction in computational time, and all degrees of freedom (DOFs) are divided into two groups including symmetrical and asymmetrical types. The results also imply the great potential for the optimization and control of the high-speed fan’s vibration for new energy cars.
- 26 February 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (4) , 1-31
Parametric Vibration and Combined Resonance of a Bending-Torsional Coupled Turbine Blade With a Preset Angle
The parametric vibration and combined resonance of a turbine blade with a preset angle subjected to the combined effect of parametric and forced excitation were investigated. The blade was modeled as a rotating beam considering the effects of centrifugal, gyroscopic, and bending-torsion coupling. The instability region of the corresponding linear system with parametric excitation was analyzed using Floquet theory, and the effect of blade parameters on this region was discussed. Notably, the parametric vibration of the torsional degree-of-freedom (DOF) caused by parametric excitation of the bending degree-of-freedom has been found. The results show that the size and position of the parameter resonance region are affected by the blade aspect ratio and preset angle, respectively. Furthermore, the multiscale method was employed to solve the blade equation under the combined action of parametric and forced excitation to study the combined resonance caused by forced excitation and gyroscopic items. The effect of blade parameters and excitation characteristics on regions of combined resonance were investigated. The phenomenon of heteroclinic bifurcation was observed due to changes in the excitation frequency, and the harmonic components that accompanied the bifurcation changed. Specifically, a multiperiod response dominated by the excitation frequency and subharmonic components shifted to a single-period response dominated by subharmonic components. This study provides a theoretical explanation for the nonsynchronous resonance of blades and the subharmonic signals in blade vibration and guides blade parameter design, especially for wind turbines.
- 26 February 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (4) , 1-31
Parametric Vibration and Combined Resonance of a Bending-Torsional Coupled Turbine Blade With a Preset Angle
The parametric vibration and combined resonance of a turbine blade with a preset angle subjected to the combined effect of parametric and forced excitation were investigated. The blade was modeled as a rotating beam considering the effects of centrifugal, gyroscopic, and bending-torsion coupling. The instability region of the corresponding linear system with parametric excitation was analyzed using Floquet theory, and the effect of blade parameters on this region was discussed. Notably, the parametric vibration of the torsional degree-of-freedom (DOF) caused by parametric excitation of the bending degree-of-freedom has been found. The results show that the size and position of the parameter resonance region are affected by the blade aspect ratio and preset angle, respectively. Furthermore, the multiscale method was employed to solve the blade equation under the combined action of parametric and forced excitation to study the combined resonance caused by forced excitation and gyroscopic items. The effect of blade parameters and excitation characteristics on regions of combined resonance were investigated. The phenomenon of heteroclinic bifurcation was observed due to changes in the excitation frequency, and the harmonic components that accompanied the bifurcation changed. Specifically, a multiperiod response dominated by the excitation frequency and subharmonic components shifted to a single-period response dominated by subharmonic components. This study provides a theoretical explanation for the nonsynchronous resonance of blades and the subharmonic signals in blade vibration and guides blade parameter design, especially for wind turbines.
- 11 October 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (2) , 1-29
Frequency Lock-In Phenomenon of Vortex Induced Vibration of a Rotating Blade Considering Bending-Torsion Coupling Effect
A rotating thin blade with bend-torsional coupling subjected to vortex induced vibration (VIV) is considered in this paper. It is necessary to study the motion coupled bending torsion due to the discordant centroid and shear center and the effect of centrifugal force at high-speed. The blade with a single axisymmetric section is regarded as a beam instead of an oscillator. The motion equation coupled bending-torsion of the blade is established by using the Euler–Lagrange equations, and the effect of centrifugal force is also employed. Vortex shedding is described by a nonlinear oscillator satisfying Van Der Pol (VDP) equation. Ritz–Galerkin method is employed to simplify the equations of the blade, and the interaction between the bending and torsion modes of blade and wake modes is discussed. The motion equation is simplified based on the contribution of the blade flutter mode. Furthermore, the single-mode approximation is used to investigate the effects of mass ratio, damping, and coupling coefficient on the locking phenomenon. It is also analyzed that the variation of flutter amplitude and locking region of the rotating blade considering bending-torsion coupling.
- 11 October 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (2) , 1-29
Frequency Lock-In Phenomenon of Vortex Induced Vibration of a Rotating Blade Considering Bending-Torsion Coupling Effect
A rotating thin blade with bend-torsional coupling subjected to vortex induced vibration (VIV) is considered in this paper. It is necessary to study the motion coupled bending torsion due to the discordant centroid and shear center and the effect of centrifugal force at high-speed. The blade with a single axisymmetric section is regarded as a beam instead of an oscillator. The motion equation coupled bending-torsion of the blade is established by using the Euler–Lagrange equations, and the effect of centrifugal force is also employed. Vortex shedding is described by a nonlinear oscillator satisfying Van Der Pol (VDP) equation. Ritz–Galerkin method is employed to simplify the equations of the blade, and the interaction between the bending and torsion modes of blade and wake modes is discussed. The motion equation is simplified based on the contribution of the blade flutter mode. Furthermore, the single-mode approximation is used to investigate the effects of mass ratio, damping, and coupling coefficient on the locking phenomenon. It is also analyzed that the variation of flutter amplitude and locking region of the rotating blade considering bending-torsion coupling.