Constantina-Dia Andreouli
Constantina-Dia Andreouli has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Athena Tsetsekou
School of Mining Engineering and Metallurgy, National Technical University of Athens, Zografou Campus, 15780 Athens, Greece
1 shared publication - Chara I. Sarafoglou
National Technical University of Athens
1 shared publication - Dimitra Giasafaki
MIRTEC S.A., Thiva Branch, 76th km of Athens–Lamia National Road, 32009 Schimatari, Greece
1 shared publication - Dimitrios Tzetzis
Digital Manufacturing and Materials Characterization Laboratory, School of Science and Technology, International Hellenic University, Thessaloniki, Greece
1 shared publication - Eleni Roussi
School of Mining and Metallurgical Engineering, National Technical University of Athens, 15780 Athens, Greece
1 shared publication - Ilias Georgiopoulos
MIRTEC S.A., Thiva Branch, 76th km of Athens–Lamia National Road, 32009 Schimatari, Greece
1 shared publication
Latest Publications
- Open Access
Water-Based Yttria-Stabilized Nano-Zirconia Pastes for Direct Ink Writing of Dental Structures
In this work, zirconia ceramic structures were fabricated by Direct Ink Writing (DIW) using water-based, yttria-stabilized nano-zirconia pastes. The pastes were prepared from 3 mol% yttria-stabilized zirconia nanopowders synthesized by sol–gel and co-precipitation routes. The effects of dispersant concentration and organic additives on paste preparation and printability were investigated, and the rheological behavior of the printable formulations was evaluated. The microstructure of the sintered 3D-printed specimens was examined by scanning electron microscopy (SEM), while apparent porosity, density, and compressive strength were determined. All printable pastes exhibited shear-thinning behavior. After sintering at 1500 °C, the printed specimens showed submicron grain sizes and apparent porosities as low as 3%. The formulation prepared without acrylamide and crosslinking agent (O12X) exhibited an apparent porosity of 3% and a compressive strength of 350 ± 25 MPa. The co-precipitated-powder formulation (2N) reached compressive-strength values of up to 360 ± 25 MPa. These results demonstrate the feasibility of using high-solids, water-based nano-zirconia pastes for DIW fabrication of dense zirconia structures and support further investigation of this approach for dental applications.
Open AccessWater-Based Yttria-Stabilized Nano-Zirconia Pastes for Direct Ink Writing of Dental Structures
In this work, zirconia ceramic structures were fabricated by Direct Ink Writing (DIW) using water-based, yttria-stabilized nano-zirconia pastes. The pastes were prepared from 3 mol% yttria-stabilized zirconia nanopowders synthesized by sol–gel and co-precipitation routes. The effects of dispersant concentration and organic additives on paste preparation and printability were investigated, and the rheological behavior of the printable formulations was evaluated. The microstructure of the sintered 3D-printed specimens was examined by scanning electron microscopy (SEM), while apparent porosity, density, and compressive strength were determined. All printable pastes exhibited shear-thinning behavior. After sintering at 1500 °C, the printed specimens showed submicron grain sizes and apparent porosities as low as 3%. The formulation prepared without acrylamide and crosslinking agent (O12X) exhibited an apparent porosity of 3% and a compressive strength of 350 ± 25 MPa. The co-precipitated-powder formulation (2N) reached compressive-strength values of up to 360 ± 25 MPa. These results demonstrate the feasibility of using high-solids, water-based nano-zirconia pastes for DIW fabrication of dense zirconia structures and support further investigation of this approach for dental applications.
- Open Access
- 24 September 2025
- Published by MDPI AG in Nanomanufacturing
- Vol. 5 (4) , 14
Friction and Wear Performance of Carbon Nanotubes Reinforced Co-Based Atmospheric Plasma-Sprayed Coatings
Atmospheric plasma spraying was used to create composite coatings employing mixed alloy matrices supplemented with carbon-based solid lubricants as feedstock materials. The current study’s goal was to examine the tribological properties of these coatings and explore the potential benefits of using CNTs as a nano-additive to minimize wear and friction while enhancing lubrication conditions in tribosystems such as piston ring–cylinder liner systems. Pin-on-disk measurements are used to correlate the chemical composition of feedstock materials with the friction coefficient and wear rate during coating operation. The enhanced behavior of the produced coatings is investigated. The anti-wear performance of Co-based cermet and metal alloys coatings, as well as the enhanced lubrication conditions during operation, are shown. In-depth discussion is provided regarding how the features of the feedstock powder affect the quality and performance of the produced coatings. The results showed that coatings based on the CoMo alloy exhibited an increase in wear due to CNT agglomeration. In contrast, CNT addition led to an improvement in bonding strength by up to 33%, a reduction in wear rate by up to 80%, and a decrease in the coefficient of friction from approximately 0.70 to 0.35 in CoNi cermet coatings. These findings demonstrate the role of CNTs in coating performance for demanding tribological applications.
- 24 September 2025
- Published by MDPI AG in Nanomanufacturing
- Vol. 5 (4) , 14
Open AccessFriction and Wear Performance of Carbon Nanotubes Reinforced Co-Based Atmospheric Plasma-Sprayed Coatings
Atmospheric plasma spraying was used to create composite coatings employing mixed alloy matrices supplemented with carbon-based solid lubricants as feedstock materials. The current study’s goal was to examine the tribological properties of these coatings and explore the potential benefits of using CNTs as a nano-additive to minimize wear and friction while enhancing lubrication conditions in tribosystems such as piston ring–cylinder liner systems. Pin-on-disk measurements are used to correlate the chemical composition of feedstock materials with the friction coefficient and wear rate during coating operation. The enhanced behavior of the produced coatings is investigated. The anti-wear performance of Co-based cermet and metal alloys coatings, as well as the enhanced lubrication conditions during operation, are shown. In-depth discussion is provided regarding how the features of the feedstock powder affect the quality and performance of the produced coatings. The results showed that coatings based on the CoMo alloy exhibited an increase in wear due to CNT agglomeration. In contrast, CNT addition led to an improvement in bonding strength by up to 33%, a reduction in wear rate by up to 80%, and a decrease in the coefficient of friction from approximately 0.70 to 0.35 in CoNi cermet coatings. These findings demonstrate the role of CNTs in coating performance for demanding tribological applications.