Mai Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mai Wang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Siyuan Liu
School of Mechanical and Aerospace Engineering, Jilin University, Chang Chun, People’s Republic of China
2 shared publications Haifei Hu
Space Robotics Engineering center, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Science,Changchun,China
1 shared publication- Haojing Bao
School of Mechanical and Aerospace Engineering, Jilin University, Chang Chun, People’s Republic of China
1 shared publication - Honglin Li
Jilin University
1 shared publication Jianhai Zhang
School of Mechanical and Aerospace Engineering Jilin University,Changchun,China
1 shared publicationMaosen Yuan
School of Mechanical and Aerospace Engineering Jilin University,Changchun,China
1 shared publication
Latest Publications
- Open Access
- 1 October 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045503
Measurement method for radial runout of sprocket based on machine vision
Due to the structural constraints of sprockets and the efficiency requirements of on-site measurements, conventional external parameter calibration methods are difficult to apply to the calibration of the sprocket hub end surface. Therefore, this paper proposes a novel external parameter calibration method based on the invariance of quadratic curves. A cylindrical object with concentric circular rings is inserted into the central hole of the sprocket, and the radii of the large and small circles on the rings, along with the radius of the sprocket hub hole, are used to derive the coefficients of the equations corresponding to the three circles. Based on these coefficients, the external parameters of the sprocket hub end surface are determined. According to the contour characteristics of the sprocket teeth, a point selection model is established to identify the highest and lowest points within the tip and root circle regions. The radial runout is then calculated as the difference in radial distances between the highest and lowest points. In the experiments, eleven sprockets of different sizes were selected as test objects, and the results obtained using the proposed method were compared with those measured by a coordinate measuring machine (CMM). The results indicate that the measurement error of the tooth root and tip circles is less than 42 μm.
- 1 October 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045503
Open AccessMeasurement method for radial runout of sprocket based on machine vision
Due to the structural constraints of sprockets and the efficiency requirements of on-site measurements, conventional external parameter calibration methods are difficult to apply to the calibration of the sprocket hub end surface. Therefore, this paper proposes a novel external parameter calibration method based on the invariance of quadratic curves. A cylindrical object with concentric circular rings is inserted into the central hole of the sprocket, and the radii of the large and small circles on the rings, along with the radius of the sprocket hub hole, are used to derive the coefficients of the equations corresponding to the three circles. Based on these coefficients, the external parameters of the sprocket hub end surface are determined. According to the contour characteristics of the sprocket teeth, a point selection model is established to identify the highest and lowest points within the tip and root circle regions. The radial runout is then calculated as the difference in radial distances between the highest and lowest points. In the experiments, eleven sprockets of different sizes were selected as test objects, and the results obtained using the proposed method were compared with those measured by a coordinate measuring machine (CMM). The results indicate that the measurement error of the tooth root and tip circles is less than 42 μm.
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A High Reflective Surface Measurement Method Based on Line Structured Light
In structured light visual measurement, the reflective characteristics of highly reflective surfaces directly affect the gray scale distribution of light stripes in the image, leading to a significant reduction in measurement accuracy. To address the impact of highly reflective surfaces on the accuracy of structured light measurements, this paper utilizes the RANSAC algorithm to process the scanned point clouds of highly reflective surfaces. By removing error points in the point cloud according to the shape characteristics of the scanned surface, the final measurement accuracy is improved. In the experiments, a highly reflective plane and a highly reflective spherical surface were selected as experimental objects. The measurement accuracy of flatness and the diameter of the measured sphere were compared before and after point cloud processing. The experimental results indicate that the measurement accuracy of flatness improved by 0.171mm, and the diameter measurement accuracy of the sphere improved by 0.103mm.
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A High Reflective Surface Measurement Method Based on Line Structured Light
In structured light visual measurement, the reflective characteristics of highly reflective surfaces directly affect the gray scale distribution of light stripes in the image, leading to a significant reduction in measurement accuracy. To address the impact of highly reflective surfaces on the accuracy of structured light measurements, this paper utilizes the RANSAC algorithm to process the scanned point clouds of highly reflective surfaces. By removing error points in the point cloud according to the shape characteristics of the scanned surface, the final measurement accuracy is improved. In the experiments, a highly reflective plane and a highly reflective spherical surface were selected as experimental objects. The measurement accuracy of flatness and the diameter of the measured sphere were compared before and after point cloud processing. The experimental results indicate that the measurement accuracy of flatness improved by 0.171mm, and the diameter measurement accuracy of the sphere improved by 0.103mm.