Ali Aourdou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ali Aourdou has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Maria José Tobar
University of A Coruña, Campus Industrial de Ferrol, CITENI, 15403 Ferrol, Spain
2 shared publications - Armando Yañez
University of A Coruña, Campus Industrial de Ferrol, CITENI, 15403 Ferrol, Spain
1 shared publication - Daniel Schlemmer
Leichtbau und Additive Fertigung, Fakultaet fuer Ingenieurwissenschaften, Rosenheim Technical University of Applied Sciences, 83024 Rosenheim, Germany
1 shared publication - Fabian Riß
Technische Hochschule Rosenheim
1 shared publication - G. García-Marquínez
Universidade da Coruña, Campus Industrial de Ferrol, Laboratorio de Aplicaciones Industriales del Láser, CITENI, 15403 Ferrol, Spain
1 shared publication - José Manuel Amado
University of A Coruña, Campus Industrial de Ferrol, CITENI, 15403 Ferrol, Spain
1 shared publication
Latest Publications
- Open Access
Comparative Microstructural and Mechanical Assessment of Wire vs. Powder Laser-DED (AISI 316L)
Laser-directed energy deposition (DED) using wire or powder feedstock is a promising way to fabricate prototypes in rapid time, including complex metal parts for advanced engineering applications. In this work, AISI 316L stainless steel—a well-known, weldable alloy model—was used to perform a foundational comparative study of wire-fed (LW-DED) and powder-fed (LP-DED) processes, establishing a baseline before progressing to high-temperature alloys. Hollow cylindrical specimens were fabricated and characterized microstructurally and mechanically. LP-DED produced a refined cellular–dendritic structure with primary dendrite arm spacing of 3.29 ± 0.49 µm and slightly higher average hardness (226 ± 8 HV0.2), accompanied by fine, spherical porosity inherent to the powder feedstock. LW-DED generated coarser epitaxial columnar dendrites (5.15 ± 0.69 µm) and slightly lower hardness (206 ± 10 HV0.2) but achieved nearly full density and high material catching efficiency. The results indicate that both methods yield comparable deposits when parameters are controlled, with LP-DED offering enhanced microstructural refinement and LW-DED providing faster deposition and higher build volume. These findings provide practical guidance for the additive manufacturing of high-performance parts and establish a baseline for the application of DED processes to advanced alloys.
Open AccessComparative Microstructural and Mechanical Assessment of Wire vs. Powder Laser-DED (AISI 316L)
Laser-directed energy deposition (DED) using wire or powder feedstock is a promising way to fabricate prototypes in rapid time, including complex metal parts for advanced engineering applications. In this work, AISI 316L stainless steel—a well-known, weldable alloy model—was used to perform a foundational comparative study of wire-fed (LW-DED) and powder-fed (LP-DED) processes, establishing a baseline before progressing to high-temperature alloys. Hollow cylindrical specimens were fabricated and characterized microstructurally and mechanically. LP-DED produced a refined cellular–dendritic structure with primary dendrite arm spacing of 3.29 ± 0.49 µm and slightly higher average hardness (226 ± 8 HV0.2), accompanied by fine, spherical porosity inherent to the powder feedstock. LW-DED generated coarser epitaxial columnar dendrites (5.15 ± 0.69 µm) and slightly lower hardness (206 ± 10 HV0.2) but achieved nearly full density and high material catching efficiency. The results indicate that both methods yield comparable deposits when parameters are controlled, with LP-DED offering enhanced microstructural refinement and LW-DED providing faster deposition and higher build volume. These findings provide practical guidance for the additive manufacturing of high-performance parts and establish a baseline for the application of DED processes to advanced alloys.
- Open Access
- 18 October 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (10) , 456
Deep Eutectic Solvents as Green and Novel Lubricant Additives for Castor Oil with High Tribological Performance
This research reveals the anti-friction and anti-wear performance of lubricants using a castor oil base and a deep eutectic solvent (DES1) as an additive. To this end, DES1 was synthesized in a successful manner using DL-menthol and dodecanoic acid as components. Mass concentrations from 0.1 wt% up to 5 wt% of DES1 additives were chosen to formulate the lubricants. Friction experiments were conducted, yielding friction enhancements up to 4% compared to the castor oil base. Notably the greatest reduction was achieved for the lubricant with 0.1 wt% of DES1. In terms of the wear generated, the best anti-wear performance was achieved for the 0.5 wt% DES1 lubricant (with a wear reduction of 17%). Furthermore, by means of the profilometry of worn surfaces, it can be observed that the tribofilm formation of DES1 on steel surfaces is a potential lubrication mechanism.
- 18 October 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (10) , 456
Open AccessDeep Eutectic Solvents as Green and Novel Lubricant Additives for Castor Oil with High Tribological Performance
This research reveals the anti-friction and anti-wear performance of lubricants using a castor oil base and a deep eutectic solvent (DES1) as an additive. To this end, DES1 was synthesized in a successful manner using DL-menthol and dodecanoic acid as components. Mass concentrations from 0.1 wt% up to 5 wt% of DES1 additives were chosen to formulate the lubricants. Friction experiments were conducted, yielding friction enhancements up to 4% compared to the castor oil base. Notably the greatest reduction was achieved for the lubricant with 0.1 wt% of DES1. In terms of the wear generated, the best anti-wear performance was achieved for the 0.5 wt% DES1 lubricant (with a wear reduction of 17%). Furthermore, by means of the profilometry of worn surfaces, it can be observed that the tribofilm formation of DES1 on steel surfaces is a potential lubrication mechanism.