Ming Wang
Research Subjects
Ming Wang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Hongliang Zhao
School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing, China
2 shared publications - Ning Wei
School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao 066004, China
2 shared publications - Chao Lv
College of Mechanical Engineering and Automation, Northeastern University 1 , Shenyang 110819
1 shared publication - Hanwen Zhang
School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao 066004, China
1 shared publication - Hongru Qiu
School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao 066004, China
1 shared publication - Jin-Xuan Yin1 shared publication
Latest Publications
- Open Access
Optimization of Key Parameters of the Air Distributor for the KYF Flotation Machine
With the decreasing availability of high-quality mineral resources and the increasing complexity of ore properties, efficient and sustainable flotation technology has become a research focus in the field of mineral processing. To optimize the taper angle of the air distributor in a KYF flotation machine, numerical simulation was used in this study to investigate its influence on the internal flow field, gas-phase characteristics, structural pressure distribution, and stirring power consumption. The results show that the peak turbulent kinetic energy and gas holdup are concentrated in the shear zone between the impeller and stator. Under the +5° condition, the peak turbulent kinetic energy is the lowest, while its vertical distribution is the most uniform. The peak gas holdup in the impeller–stator region reaches 19.2%, and the number of efficient bubbles with a diameter of 0.5 mm reaches 3.8 × 106 per m3, which is significantly higher than under the other conditions. During stable operation, this condition exhibits the lowest stirring power consumption at 126.0 W, which is 7.557% and 4.255% lower than under the −5° and 0° conditions, respectively. The optimal taper angle is therefore determined to be +5°. However, the associated large pressure gradient on the impeller surface may accelerate blade wear, indicating that surface strengthening measures should be considered to balance performance and durability.
Open AccessOptimization of Key Parameters of the Air Distributor for the KYF Flotation Machine
With the decreasing availability of high-quality mineral resources and the increasing complexity of ore properties, efficient and sustainable flotation technology has become a research focus in the field of mineral processing. To optimize the taper angle of the air distributor in a KYF flotation machine, numerical simulation was used in this study to investigate its influence on the internal flow field, gas-phase characteristics, structural pressure distribution, and stirring power consumption. The results show that the peak turbulent kinetic energy and gas holdup are concentrated in the shear zone between the impeller and stator. Under the +5° condition, the peak turbulent kinetic energy is the lowest, while its vertical distribution is the most uniform. The peak gas holdup in the impeller–stator region reaches 19.2%, and the number of efficient bubbles with a diameter of 0.5 mm reaches 3.8 × 106 per m3, which is significantly higher than under the other conditions. During stable operation, this condition exhibits the lowest stirring power consumption at 126.0 W, which is 7.557% and 4.255% lower than under the −5° and 0° conditions, respectively. The optimal taper angle is therefore determined to be +5°. However, the associated large pressure gradient on the impeller surface may accelerate blade wear, indicating that surface strengthening measures should be considered to balance performance and durability.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Numerical comparison of two-phase flow characteristics for different nozzle designs in double-sided blowing furnaces
To investigate the influence of nozzle design on the homogeneity of mixing and smelting efficiency within a double-sided blowing furnace during the smelting process, a computational fluid dynamics simulation was carried out using the volume of fluid model, and the realizable turbulence k-ε model to simulate the liquid flow within the furnace. Analysis of furnace velocity distribution across operating conditions revealed that penetration depth variations correlated with bubble generation, bubble growth, bubble rise, and bubble breakage. To optimize molten pool mixing efficiency, four nozzle configurations were proposed: (1) cone straight shape; (2) excessive rounded corners; (3) conical; (4) anti-conical. Among these improved nozzle types, the conical nozzle demonstrated the best improvement effect. Compared to the ordinary nozzle, the dead zone proportion decreased by 16.57% and the penetration depth increased by 57.28%. Furthermore, this study also proposes combining nozzle types with distribution patterns. The relative conical mode stands out, showing an average velocity increase in 117.37%, a 37.17% reduction in dead zone proportion, and a 45.06% decrease in splash mass, compared to the ordinary nozzle.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Numerical comparison of two-phase flow characteristics for different nozzle designs in double-sided blowing furnaces
To investigate the influence of nozzle design on the homogeneity of mixing and smelting efficiency within a double-sided blowing furnace during the smelting process, a computational fluid dynamics simulation was carried out using the volume of fluid model, and the realizable turbulence k-ε model to simulate the liquid flow within the furnace. Analysis of furnace velocity distribution across operating conditions revealed that penetration depth variations correlated with bubble generation, bubble growth, bubble rise, and bubble breakage. To optimize molten pool mixing efficiency, four nozzle configurations were proposed: (1) cone straight shape; (2) excessive rounded corners; (3) conical; (4) anti-conical. Among these improved nozzle types, the conical nozzle demonstrated the best improvement effect. Compared to the ordinary nozzle, the dead zone proportion decreased by 16.57% and the penetration depth increased by 57.28%. Furthermore, this study also proposes combining nozzle types with distribution patterns. The relative conical mode stands out, showing an average velocity increase in 117.37%, a 37.17% reduction in dead zone proportion, and a 45.06% decrease in splash mass, compared to the ordinary nozzle.