MMMario Andres Martinez

Mario Andres Martinez

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mario Andres Martinez has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Surface-Functionalized Nanofibers via Green Electrospinning: A Sustainable Platform for Enzyme Immobilization

    by Mario Andres Martinez, Tatiana Guendulain, Marcos Heredero, Ana Beloqui, Edurne González

    In this work, we present a sustainable and efficient approach for the fabrication of surface-functionalized nanofibers via green electrospinning, an aqueous-based technique that employs polymer latexes and eliminates the need for organic solvents. Three carboxylic acid and one epoxy-functionalized latexes were synthesized through seeded semibatch emulsion polymerization using acrylic acid and glycidyl methacrylate as functional comonomers, alongside methyl methacrylate and butyl acrylate as the main monomers. The resulting latexes were blended with polyvinyl alcohol (PVA) as a sacrificial template polymer and electrospun into continuous nanofibers. The obtained nanofibers were thermally annealed at 80 °C to promote particle coalescence, followed by water treatment to remove the PVA, yielding homogeneous nanofibers with accessible surface functional groups. The accessibility and reactivity of the surface functional groups were demonstrated through the covalent immobilization of cutinase via NHS-ester and epoxy–amine coupling reactions, yielding stable and catalytically active biocatalytic nanofibers. Carboxylic acid-functionalized nanofibers showed immobilization yields of 10–18% and specific activities of 100–200 µmol min–1 mg–1. In contrast, epoxy-functionalized nanofibers exhibited a lower immobilization yield of approximately 5% but a substantially higher specific activity of approximately 330 µmol min–1 mg–1. This lower enzyme loading may favor a less densely packed immobilization, reducing steric constraints and improving enzyme accessibility and catalytic efficiency. Moreover, the epoxy-functionalized nanofiber mats exhibited enhanced operational and storage stability, significantly extending the lifetime of the immobilized biocatalyst. This approach provides a straightforward and environmentally friendly route to produce functional nanofibers without the use of organic solvents or post-spinning chemical modification steps, offering significant potential for applications in biosensing, biocatalysis, biomedical engineering, and environmental remediation.

  • Open Access

    Fabrication of photocatalytic nanofibers by suspension electrospinning

    by Mario Andres Martinez, Lide Arana, Edurne González

  • Open Access

    Fabrication of photocatalytic nanofibers by Green Electrospinning

    by Mario Martinez, Lide Arana, Edurne Gonzalez

    Green Electrospinning was employed to fabricate photocatalytic nanofibers designed for environmental remediation. To this end, methyl methacrylate/n‐butyl acrylate (MMA/BA) copolymer particles stabilized with ultrafine titanium dioxide nanoparticles (TiO2 NPs) were synthesized via miniemulsion polymerization. Two latexes with a solids content of 40 wt % were prepared, containing 10 and 20 wt % TiO2 NPs (based on monomers). These latexes were successfully electrospun using polyvinyl alcohol (PVA) as a template polymer, with a minimum PVA concentration of 30 wt % required to obtain continuous nanofibers. The resulting fibers contained only 3 and 6 wt % TiO2 NPs . Since TiO2 NPs were strongly adsorbed onto the polymer particle´s surface, an excellent distribution of the NPs along the nanofibers (without any aggregation) was guaranteed. The hybrid nanofibers were subsequently crosslinked to enhance their water stability. Their photocatalytic performance was evaluated through methylene blue (MB) degradation and Escherichia coli (E. coli) inactivation tests. In both cases, the nanofibers exhibited significantly higher activity than corresponding films, attributable to their much larger surface area to volume ratio. Additionally, increasing the TiO2 NPs content improved both MB degradation and bacterial inactivation efficiency. Moreover, the nanofibers demonstrated good reusability. Overall, this work highlights the potential of Green Electrospinning as a solvent‐free approach to produce highly photocatalytic nanofibers capable of removing organic pollutants and pathogenic bacteria from water.

  • Open Access

    Strategies to Improve the Water Resistance of Nanofibers Obtained by Suspension Electrospinning

    by Mario Andres Martinez, Edurne González

    Suspension Electrospinning involves electrospinning a latex (an aqueous dispersion of polymer particles) with the help of a water‐soluble template polymer. This method is promising as it enables the spinning of hydrophobic polymers using water as an electrospinning medium, thereby eliminating the need for toxic organic solvents. However, Suspension Electrospinning presents some challenges, as the use of a template polymer is necessary to form continuous fibers, but increasing its amount reduces the fibers´ water resistance. This work focuses on producing water‐resistant nanofibers by optimizing template concentration and exploring new strategies. The minimum template concentration needed to produce uniform, water‐resistant nanofibers from a monomodal acrylic latex is identified. Additionally, a high solids content bimodal acrylic latex is spun for the first time, enhancing process productivity and allowing a 50% reduction in the template polymer compared to the monomodal system. Two additional novel strategies are employed to increase the water resistance of the nanofibers: thermal cross‐linking of a carboxylic acid functionalized latex with polyvinyl alcohol (PVA) and spinning a high glass transition temperature latex followed by its coalescence before the template removal. Finally, the effectiveness of PVA and polyethylene oxide (PEO) as template polymers is compared.