A. R. Smith
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
A. R. Smith has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Craig P. Allford
Cardiff University
2 shared publications - George M. Jandu
Cardiff University
2 shared publications - Peter Michael Smowton
Cardiff University
2 shared publications - S V Power
Cardiff University
2 shared publications A Clark
IQE Inc
1 shared publication- Huiwen Deng
Department of Electronic and Electrical Engineering, University College London, London, U.K.
1 shared publication
Latest Publications
- Open Access
- 18 August 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (33) , 335102
On-wafer characterisation of 1300 nm InAs quantum dot laser uniformity over 150 mm substrates
We report wafer scale characterisation of O-band 150 mm InAs quantum dot edge-emitting lasers, using on-wafer measurements of etched-facet lasers. Threshold current, lasing wavelength, and spontaneous emission spectra were mapped across the wafer and compared with post-growth photoluminescence (PL) peak emission wavelength and full-width half-maximum (FWHM) to evaluate device performance and uniformity. Strong correlation is observed between the post-growth PL data and the on-wafer laser characteristics. Pearson correlation coefficients of 0.93 were calculated between both PL peak emission wavelength and peak lasing wavelength, and PL peak emission wavelength and peak spontaneous emission wavelength. A coefficient of 0.56 was found between PL FWHM and threshold current. Together, these indicate excellent fabrication uniformity and demonstrate that device performance is strongly correlated with variations in the epitaxial growth. The PL peak emission wavelength and FWHM were 1281.70 nm and 57.90 nm with standard deviations of 1.00 nm and 1.62 nm, respectively. The low fabrication variability enables a lasing yield of 98.2 % (of lasers with thresholds below the maximum current used during characterisation of 1.5 A) for a population of 1152 devices with a 2000 µm cavity length. By combining on-wafer etched-facet measurements with post singulation measurements on both cleaved-facet lasers alongside gain and absorption measurements from the segmented-contact method, the etched-facet reflectivity at 6 mm from the wafers centre was extracted to be 0.074 ± 0.003. Additional investigation indicates that the sub-optimal etched-facet reflectivity is likely due to off-vertical angled facets, measured at 81.8 ∘ relative to the wafer surface, which increases mirror losses, raising the threshold current and reducing yield for shorter cavity devices due to the higher gain requirement. Overall, the spatial uniformity of the facet reflectivity demonstrates that on-wafer etched-facet test structures provide a robust platform for diagnosing epitaxial and fabrication variations without the need for extensive wafer cleaving.
- 18 August 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (33) , 335102
Open AccessOn-wafer characterisation of 1300 nm InAs quantum dot laser uniformity over 150 mm substrates
We report wafer scale characterisation of O-band 150 mm InAs quantum dot edge-emitting lasers, using on-wafer measurements of etched-facet lasers. Threshold current, lasing wavelength, and spontaneous emission spectra were mapped across the wafer and compared with post-growth photoluminescence (PL) peak emission wavelength and full-width half-maximum (FWHM) to evaluate device performance and uniformity. Strong correlation is observed between the post-growth PL data and the on-wafer laser characteristics. Pearson correlation coefficients of 0.93 were calculated between both PL peak emission wavelength and peak lasing wavelength, and PL peak emission wavelength and peak spontaneous emission wavelength. A coefficient of 0.56 was found between PL FWHM and threshold current. Together, these indicate excellent fabrication uniformity and demonstrate that device performance is strongly correlated with variations in the epitaxial growth. The PL peak emission wavelength and FWHM were 1281.70 nm and 57.90 nm with standard deviations of 1.00 nm and 1.62 nm, respectively. The low fabrication variability enables a lasing yield of 98.2 % (of lasers with thresholds below the maximum current used during characterisation of 1.5 A) for a population of 1152 devices with a 2000 µm cavity length. By combining on-wafer etched-facet measurements with post singulation measurements on both cleaved-facet lasers alongside gain and absorption measurements from the segmented-contact method, the etched-facet reflectivity at 6 mm from the wafers centre was extracted to be 0.074 ± 0.003. Additional investigation indicates that the sub-optimal etched-facet reflectivity is likely due to off-vertical angled facets, measured at 81.8 ∘ relative to the wafer surface, which increases mirror losses, raising the threshold current and reducing yield for shorter cavity devices due to the higher gain requirement. Overall, the spatial uniformity of the facet reflectivity demonstrates that on-wafer etched-facet test structures provide a robust platform for diagnosing epitaxial and fabrication variations without the need for extensive wafer cleaving.
- Open Access
- 1 October 2025
- Published by AIP Publishing in APL Photonics
- Vol. 10 (10)
Optical gain in O-band active regions with multiple dot-in-well layers
The optimum number of layers in InAs-based quantum dot-in-well active regions is investigated by means of sophisticated measurements of structures containing 8, 12, and 14 dot-in-well layers. Measurements of optical gain vs a parameter proportional to the carrier density indicate that additional layers do provide a proportional increase in the available gain at a given carrier density. This indicates that unequal optical overlap and unequal electrical pumping of the different layers are not significant effects. It is suggested that performance better than that of the typically used seven or eight layers may occur for samples with a higher layer number with reduced levels of p-modulation doping to minimize internal optical mode loss and non-radiative recombination.
- 1 October 2025
- Published by AIP Publishing in APL Photonics
- Vol. 10 (10)
Open AccessOptical gain in O-band active regions with multiple dot-in-well layers
The optimum number of layers in InAs-based quantum dot-in-well active regions is investigated by means of sophisticated measurements of structures containing 8, 12, and 14 dot-in-well layers. Measurements of optical gain vs a parameter proportional to the carrier density indicate that additional layers do provide a proportional increase in the available gain at a given carrier density. This indicates that unequal optical overlap and unequal electrical pumping of the different layers are not significant effects. It is suggested that performance better than that of the typically used seven or eight layers may occur for samples with a higher layer number with reduced levels of p-modulation doping to minimize internal optical mode loss and non-radiative recombination.