Jun Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jun Lu has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Shuize Wang
Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing, China
8 shared publications - Yuhe Huang
Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing 100083, China
8 shared publications - Chaolei Zhang
Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing 100083, China
4 shared publications - Haitao Zhao
Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing, China
4 shared publications - Hong-Hui Wu
Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing 100083, China
4 shared publications - Junheng Gao
Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing, China
3 shared publications
Latest Publications
- Open Access
Effect of Nb Microalloying on the Dynamic Recrystallization, Bainitic Microstructure, and Mechanical Properties of Hot-Rolled Bainitic Steels
Controlling prior austenite morphology during single-pass hot rolling is essential for improving the strength–ductility balance of strip casting high-strength steels. In this study, Fe–0.24C–1.5Si–1.8Mn steels with and without 0.03 wt.% Nb were deformed by 50% at 950–1100 °C and subsequently held at 350 °C for 60 min for bainitic transformation. The effects of deformation temperature and Nb addition on austenite dynamic recrystallization, bainitic microstructure, and mechanical properties were investigated. For the Nb-free steel, recrystallization occurred at all these investigated deformation temperatures. The addition of 0.03 wt.% Nb markedly suppressed austenite recrystallization during hot deformation, resulting in the retention of elongated deformed austenite after deformation at 950 °C. Compared with the bainitic microstructure formed from fine recrystallized austenite in the 0Nb steel (without Nb addition), that formed from elongated austenite in the 03Nb steel (with 0.03 wt.% Nb) deformed at 950 °C exhibited a smaller lath width and higher HAGB and dislocation densities. In addition, the volume fraction of retained austenite increased from 4.5% to 9.8%, while its average thickness decreased from 105.6 nm to 49.1 nm. Consequently, under identical deformation conditions (50% reduction at 950 °C), Nb addition increased the yield and tensile strengths from 1064 MPa and 1261 MPa to 1088 MPa and 1323 MPa, respectively, while the total elongation remained nearly unchanged (24.8% vs 24.6%). These findings provide new insights into the optimization of thermomechanical processing for strip casting bainitic steels.
Open AccessEffect of Nb Microalloying on the Dynamic Recrystallization, Bainitic Microstructure, and Mechanical Properties of Hot-Rolled Bainitic Steels
Controlling prior austenite morphology during single-pass hot rolling is essential for improving the strength–ductility balance of strip casting high-strength steels. In this study, Fe–0.24C–1.5Si–1.8Mn steels with and without 0.03 wt.% Nb were deformed by 50% at 950–1100 °C and subsequently held at 350 °C for 60 min for bainitic transformation. The effects of deformation temperature and Nb addition on austenite dynamic recrystallization, bainitic microstructure, and mechanical properties were investigated. For the Nb-free steel, recrystallization occurred at all these investigated deformation temperatures. The addition of 0.03 wt.% Nb markedly suppressed austenite recrystallization during hot deformation, resulting in the retention of elongated deformed austenite after deformation at 950 °C. Compared with the bainitic microstructure formed from fine recrystallized austenite in the 0Nb steel (without Nb addition), that formed from elongated austenite in the 03Nb steel (with 0.03 wt.% Nb) deformed at 950 °C exhibited a smaller lath width and higher HAGB and dislocation densities. In addition, the volume fraction of retained austenite increased from 4.5% to 9.8%, while its average thickness decreased from 105.6 nm to 49.1 nm. Consequently, under identical deformation conditions (50% reduction at 950 °C), Nb addition increased the yield and tensile strengths from 1064 MPa and 1261 MPa to 1088 MPa and 1323 MPa, respectively, while the total elongation remained nearly unchanged (24.8% vs 24.6%). These findings provide new insights into the optimization of thermomechanical processing for strip casting bainitic steels.
- Open Access
Coupled Enrichment of Cu and Sn at the Oxide/Steel Interface and Its Regulation by Si in Recycled Steels
The accumulation of residual elements such as Cu and Sn in recycled steels has become an increasingly critical issue, as their enrichment during high-temperature oxidation can lead to surface hot shortness and deterioration of surface quality. In this work, the coupled enrichment behavior of Cu and Sn at the oxide/steel interface and its regulation by Si were systematically investigated through high-temperature oxidation experiments and microstructural characterization. The results reveal that selective oxidation of Fe during high-temperature exposure leads to the rejection of Cu toward the oxide/steel interface, resulting in significant interfacial enrichment. The presence of Sn further intensifies this enrichment by lowering the melting point of the Cu-rich phase and promoting the formation of Cu–Sn liquid films along grain boundaries, thereby aggravating intergranular penetration and surface degradation. In contrast, the addition of Si effectively suppresses the interfacial enrichment of Cu and Sn. Microstructural analyses indicate that Si promotes internal oxidation and facilitates the formation of Si-containing oxides such as Fe2SiO4 within the oxide scale and near the interface, which modifies the interfacial structure and limits the diffusion and accumulation of Cu-rich phases. Consequently, the formation and penetration of Cu–Sn liquid are significantly inhibited. These findings clarify the coupling mechanism of Cu and Sn during oxidation and reveal an effective Si-based strategy for mitigating the detrimental enrichment of residual elements in recycled steels, providing guidance for improving the surface quality of steels produced from scrap-containing charges.
Open AccessCoupled Enrichment of Cu and Sn at the Oxide/Steel Interface and Its Regulation by Si in Recycled Steels
The accumulation of residual elements such as Cu and Sn in recycled steels has become an increasingly critical issue, as their enrichment during high-temperature oxidation can lead to surface hot shortness and deterioration of surface quality. In this work, the coupled enrichment behavior of Cu and Sn at the oxide/steel interface and its regulation by Si were systematically investigated through high-temperature oxidation experiments and microstructural characterization. The results reveal that selective oxidation of Fe during high-temperature exposure leads to the rejection of Cu toward the oxide/steel interface, resulting in significant interfacial enrichment. The presence of Sn further intensifies this enrichment by lowering the melting point of the Cu-rich phase and promoting the formation of Cu–Sn liquid films along grain boundaries, thereby aggravating intergranular penetration and surface degradation. In contrast, the addition of Si effectively suppresses the interfacial enrichment of Cu and Sn. Microstructural analyses indicate that Si promotes internal oxidation and facilitates the formation of Si-containing oxides such as Fe2SiO4 within the oxide scale and near the interface, which modifies the interfacial structure and limits the diffusion and accumulation of Cu-rich phases. Consequently, the formation and penetration of Cu–Sn liquid are significantly inhibited. These findings clarify the coupling mechanism of Cu and Sn during oxidation and reveal an effective Si-based strategy for mitigating the detrimental enrichment of residual elements in recycled steels, providing guidance for improving the surface quality of steels produced from scrap-containing charges.
- Open Access
Effect of Si on Marine Corrosion Behavior of Austenite Low-Density Steel
To address the high-salinity and hyper-humid thermal environment of tropical oceans and meet industrial demands for high strength and lightweight, austenitic low-density steel was developed as a novel corrosion-resistant steel. A 3.5 wt.% NaCl solution was used to simulate the marine environment to study the effect of Si on the corrosion behavior of this steel. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and electron probe microanalysis (EPMA) were employed to characterize the microstructures and corrosion behaviors of two test steels, as well as the phase compositions and element distributions of corrosion products after polarization and cyclic immersion accelerated corrosion tests. The results show that a dense oxide film initially forms on the steel surface in 3.5 wt.% NaCl solution at the early corrosion stage. Si addition induces SiO2 formation and promotes Al conversion to Al2O3, enhancing oxide film compactness and inhibiting matrix atom outward diffusion and Cl− inward penetration. With prolonged corrosion, the oxide film is dissolved or broken, forming a dense rust layer dominated by Fe3O4, Fe2O3 and FeOOH. Si enriches in the inner rust layer adjacent to the matrix and pitting cavities, inhibiting pitting deepening and promoting γ-FeOOH to α-FeOOH transformation, thus improving the steel’s corrosion resistance.
Open AccessEffect of Si on Marine Corrosion Behavior of Austenite Low-Density Steel
To address the high-salinity and hyper-humid thermal environment of tropical oceans and meet industrial demands for high strength and lightweight, austenitic low-density steel was developed as a novel corrosion-resistant steel. A 3.5 wt.% NaCl solution was used to simulate the marine environment to study the effect of Si on the corrosion behavior of this steel. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and electron probe microanalysis (EPMA) were employed to characterize the microstructures and corrosion behaviors of two test steels, as well as the phase compositions and element distributions of corrosion products after polarization and cyclic immersion accelerated corrosion tests. The results show that a dense oxide film initially forms on the steel surface in 3.5 wt.% NaCl solution at the early corrosion stage. Si addition induces SiO2 formation and promotes Al conversion to Al2O3, enhancing oxide film compactness and inhibiting matrix atom outward diffusion and Cl− inward penetration. With prolonged corrosion, the oxide film is dissolved or broken, forming a dense rust layer dominated by Fe3O4, Fe2O3 and FeOOH. Si enriches in the inner rust layer adjacent to the matrix and pitting cavities, inhibiting pitting deepening and promoting γ-FeOOH to α-FeOOH transformation, thus improving the steel’s corrosion resistance.
- Open Access
Nitrogen Enables Superior Strength–Ductility Synergy in Ultra-Low Carbon Steel via Copious Interphase Precipitation and Grain Refinement
The increasing use of electric arc furnace (EAF) in steelmaking inevitably elevates nitrogen (N) levels, which are traditionally regarded as a detrimental element to the formability of ultra-low carbon (ULC) steels due to the formation of Lüders band. Here, we demonstrate that N could act as a beneficial microalloying element in strip casting ULC steels by promoting V(C, N) precipitation and grain refinement of ferrite. Thermodynamic calculations reveal that N significantly increases both the equilibrium volume fraction and equilibrium precipitation temperature of V(C, N), enabling copious interphase nanoprecipitation during ferrite transformation. Microstructural characterization confirms the enhanced formation of V(C, N) within interphase rows in the N-containing steels, leading to greater Zener pinning effect and smaller ferrite grain size (from 7.50 μm of 0N to 4.67 μm of 96 ppm N and 3.84 μm of 139 ppm N). As a result, owing to the enhanced nanoprecipitation and grain refinement, the N-containing ULC strip casting steels exhibit a superior strength–ductility synergy, with tensile strength increased from 666 MPa (0N) to 805 MPa (96 ppm N) and 825 MPa (139 ppm N), and a slight decrease in total elongation from 29.8% (0N) to 27.3% (96 ppm N) and 22.0% (139 ppm N). In addition, no Lüders plateau was observed in the tensile stress-strain curves as the extensive formation of V(C, N) consumed the N atoms in solid solution. These findings highlight that microalloying V in the steels produced by EAF can effectively leverage the high N content for achieving superior strength–ductility synergy.
Open AccessNitrogen Enables Superior Strength–Ductility Synergy in Ultra-Low Carbon Steel via Copious Interphase Precipitation and Grain Refinement
The increasing use of electric arc furnace (EAF) in steelmaking inevitably elevates nitrogen (N) levels, which are traditionally regarded as a detrimental element to the formability of ultra-low carbon (ULC) steels due to the formation of Lüders band. Here, we demonstrate that N could act as a beneficial microalloying element in strip casting ULC steels by promoting V(C, N) precipitation and grain refinement of ferrite. Thermodynamic calculations reveal that N significantly increases both the equilibrium volume fraction and equilibrium precipitation temperature of V(C, N), enabling copious interphase nanoprecipitation during ferrite transformation. Microstructural characterization confirms the enhanced formation of V(C, N) within interphase rows in the N-containing steels, leading to greater Zener pinning effect and smaller ferrite grain size (from 7.50 μm of 0N to 4.67 μm of 96 ppm N and 3.84 μm of 139 ppm N). As a result, owing to the enhanced nanoprecipitation and grain refinement, the N-containing ULC strip casting steels exhibit a superior strength–ductility synergy, with tensile strength increased from 666 MPa (0N) to 805 MPa (96 ppm N) and 825 MPa (139 ppm N), and a slight decrease in total elongation from 29.8% (0N) to 27.3% (96 ppm N) and 22.0% (139 ppm N). In addition, no Lüders plateau was observed in the tensile stress-strain curves as the extensive formation of V(C, N) consumed the N atoms in solid solution. These findings highlight that microalloying V in the steels produced by EAF can effectively leverage the high N content for achieving superior strength–ductility synergy.
- Open Access
Thermo-History-Dependent Copper Enrichment During High-Temperature Oxidation of Recycled Steels
The utilization of recycled steel is essential for achieving carbon neutrality and sustainable engineering, yet repeated recycling inevitably leads to the accumulation of residual elements that are difficult to remove during conventional refining. Among them, copper (Cu) readily enriches in scrap-based steels and is a primary cause of surface hot shortness during high-temperature processing due to its segregation at the oxide/steel interface. While the compositional effects of Cu have been extensively studied, the influence of thermo-history associated with different industrial processing routes remains poorly understood. In this work, Cu enrichment during high-temperature oxidation was systematically investigated under thermo-histories representative of conventional hot rolling, thin slab continuous casting and rolling (TSCR), and strip casting. Plain carbon steels containing 0.05–0.30 wt.% Cu were oxidized at 1000–1200 °C, and interfacial microstructures were characterized using SEM–EDS. The results show that Cu enrichment is highly sensitive to both temperature and thermal exposure time, with a critical temperature range of 1100–1150 °C promoting the formation of continuous Cu-rich liquid films. Prolonged thermo-history in conventional hot rolling markedly enhances Cu enrichment, TSCR partially suppresses interfacial segregation, whereas strip casting effectively inhibits Cu enrichment even at elevated Cu contents. These findings highlight thermo-history as a dominant factor controlling Cu-induced surface hot shortness and provide guidance for process optimization in recycled steels.
Open AccessThermo-History-Dependent Copper Enrichment During High-Temperature Oxidation of Recycled Steels
The utilization of recycled steel is essential for achieving carbon neutrality and sustainable engineering, yet repeated recycling inevitably leads to the accumulation of residual elements that are difficult to remove during conventional refining. Among them, copper (Cu) readily enriches in scrap-based steels and is a primary cause of surface hot shortness during high-temperature processing due to its segregation at the oxide/steel interface. While the compositional effects of Cu have been extensively studied, the influence of thermo-history associated with different industrial processing routes remains poorly understood. In this work, Cu enrichment during high-temperature oxidation was systematically investigated under thermo-histories representative of conventional hot rolling, thin slab continuous casting and rolling (TSCR), and strip casting. Plain carbon steels containing 0.05–0.30 wt.% Cu were oxidized at 1000–1200 °C, and interfacial microstructures were characterized using SEM–EDS. The results show that Cu enrichment is highly sensitive to both temperature and thermal exposure time, with a critical temperature range of 1100–1150 °C promoting the formation of continuous Cu-rich liquid films. Prolonged thermo-history in conventional hot rolling markedly enhances Cu enrichment, TSCR partially suppresses interfacial segregation, whereas strip casting effectively inhibits Cu enrichment even at elevated Cu contents. These findings highlight thermo-history as a dominant factor controlling Cu-induced surface hot shortness and provide guidance for process optimization in recycled steels.
- Open Access
Evolution of Cluster Morphology and Its Impact on Dislocation Behavior in a Strip-Cast HSLA Steel
Strip casting presents a sustainable route for producing advanced steels, such as high-strength low-alloy (HSLA) grades. This study investigated how early-stage isothermal holding (120–1800 s at 923 K) affects the evolution of cluster morphology and its subsequent impact on dislocation behavior and mechanical properties in a strip-cast Nb-bearing HSLA steel. Advanced characterization (atom probe tomography) revealed that prolonged holding promotes the growth of nanoscale Nb-(C,N) clusters and precipitates, accompanied by an increase in ferrite fraction. Remarkably, this evolution simultaneously enhances both strength and ductility. Enhanced ductility and sustained work hardening are linked to a higher density and volume fraction of nanoscale particles, which act as potent obstacles for dislocation nucleation and multiplication. These findings establish a critical link between cluster evolution and dislocation-mediated strengthening, providing a basis for optimizing strip-cast steels.
Open AccessEvolution of Cluster Morphology and Its Impact on Dislocation Behavior in a Strip-Cast HSLA Steel
Strip casting presents a sustainable route for producing advanced steels, such as high-strength low-alloy (HSLA) grades. This study investigated how early-stage isothermal holding (120–1800 s at 923 K) affects the evolution of cluster morphology and its subsequent impact on dislocation behavior and mechanical properties in a strip-cast Nb-bearing HSLA steel. Advanced characterization (atom probe tomography) revealed that prolonged holding promotes the growth of nanoscale Nb-(C,N) clusters and precipitates, accompanied by an increase in ferrite fraction. Remarkably, this evolution simultaneously enhances both strength and ductility. Enhanced ductility and sustained work hardening are linked to a higher density and volume fraction of nanoscale particles, which act as potent obstacles for dislocation nucleation and multiplication. These findings establish a critical link between cluster evolution and dislocation-mediated strengthening, providing a basis for optimizing strip-cast steels.
- Open Access
Unexpected Enhancement of High-Cycle Fatigue Property in Hot-Rolled DP600 Steel via Grain Size Tailoring
This work systematically investigates the high-cycle fatigue (HCF) properties and fatigue crack growth (FCG) behavior of hot-rolled dual-phase (DP) steels with comparable tensile strength but distinctly different yield strength (458 MPa for the FG sample and 355 MPa for the CG sample), grain sizes and morphologies. Contrary to the conventional Hall–Petch relationship, the coarse-grained (CG) sample demonstrates superior fatigue performance. This enhancement is reflected in its higher fatigue strength, combined with an elevated FCG threshold and a reduced FCG rate in the Paris regime of FCG behavior. Fracture morphologies and FCG path analyses reveal that this enhanced fatigue resistance attributes to pronounced crack path tortuosity in the CG microstructure. The tortuous crack path enhances roughness-induced crack closure effects in the near-threshold regime while promoting more frequent crack deflection during stable propagation, collectively reducing the effective driving force for crack growth. The experimental evidence confirms that properly designed CG microstructures with appropriate phase distribution can provide superior fatigue resistance in hot-rolled DP steels.
Open AccessUnexpected Enhancement of High-Cycle Fatigue Property in Hot-Rolled DP600 Steel via Grain Size Tailoring
This work systematically investigates the high-cycle fatigue (HCF) properties and fatigue crack growth (FCG) behavior of hot-rolled dual-phase (DP) steels with comparable tensile strength but distinctly different yield strength (458 MPa for the FG sample and 355 MPa for the CG sample), grain sizes and morphologies. Contrary to the conventional Hall–Petch relationship, the coarse-grained (CG) sample demonstrates superior fatigue performance. This enhancement is reflected in its higher fatigue strength, combined with an elevated FCG threshold and a reduced FCG rate in the Paris regime of FCG behavior. Fracture morphologies and FCG path analyses reveal that this enhanced fatigue resistance attributes to pronounced crack path tortuosity in the CG microstructure. The tortuous crack path enhances roughness-induced crack closure effects in the near-threshold regime while promoting more frequent crack deflection during stable propagation, collectively reducing the effective driving force for crack growth. The experimental evidence confirms that properly designed CG microstructures with appropriate phase distribution can provide superior fatigue resistance in hot-rolled DP steels.
- Open Access
Titanium Modulated the Occurrence States and Strain Aging Resistance of Residual Element Nitrogen in Scrap-Based Low-Alloy Steels
The steel industry is responsible for 7–9% of global CO2 emissions. Shifting from primary iron ore to recycled scrap in electric arc furnace (EAF) steelmaking offers significant decarbonization potential, reducing carbon intensity by 60–70%. However, increased scrap use in EAF operations leads to higher nitrogen absorption, which can degrade mechanical properties. Nitrogen dissolves into molten steel, where it forms Cottrell atmospheres at dislocations in the following processing steps, intensifying strain aging and reducing ductility. This study establishes a precipitation criterion based on the TiN solubility product to prevent harmful liquid TiN formation, enabling effective nitrogen fixation via fine TiN precipitates (5–20 nm). Multiscale characterization techniques, such as TEM and EBSD, show that Ti reduces the number of mobile N atoms by 60–70%, evidenced by a 50–65% decrease in Snoek/SKK peak intensities. Excessive titanium can refine ferrite grain size and prevents harmful TiN inclusions. Titanium microalloying presents a cost-effective, sustainable strategy to reduce strain aging in scrap-rich EAF steels, enabling more sustainable steel production without sacrificing material properties.
Open AccessTitanium Modulated the Occurrence States and Strain Aging Resistance of Residual Element Nitrogen in Scrap-Based Low-Alloy Steels
The steel industry is responsible for 7–9% of global CO2 emissions. Shifting from primary iron ore to recycled scrap in electric arc furnace (EAF) steelmaking offers significant decarbonization potential, reducing carbon intensity by 60–70%. However, increased scrap use in EAF operations leads to higher nitrogen absorption, which can degrade mechanical properties. Nitrogen dissolves into molten steel, where it forms Cottrell atmospheres at dislocations in the following processing steps, intensifying strain aging and reducing ductility. This study establishes a precipitation criterion based on the TiN solubility product to prevent harmful liquid TiN formation, enabling effective nitrogen fixation via fine TiN precipitates (5–20 nm). Multiscale characterization techniques, such as TEM and EBSD, show that Ti reduces the number of mobile N atoms by 60–70%, evidenced by a 50–65% decrease in Snoek/SKK peak intensities. Excessive titanium can refine ferrite grain size and prevents harmful TiN inclusions. Titanium microalloying presents a cost-effective, sustainable strategy to reduce strain aging in scrap-rich EAF steels, enabling more sustainable steel production without sacrificing material properties.