Abdul Azim Abdullah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abdul Azim Abdullah has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Razak Abdul Karim
Universiti Malaysia Sarawak
3 shared publications - Ahmad Beng Hong Kueh
Department of Civil Engineering, Faculty of Engineering, Universiti Malaysia Sarawak, Kota Samarahan, Malaysia
2 shared publications - Norazzlina M. Sa’don
Universiti Malaysia Sarawak
2 shared publications - Pierre Quenneville
Dept. of Civil and Environmental Engineering Univ. of Auckland Auckland New Zealand
2 shared publications - Siti Hanim Sahari2 shared publications
Abdul Razak Abdul Karim
Department of Civil Engineering, Universiti Malaysia Sarawak, 94300 Kota Samarahan, Malaysia
1 shared publication
Latest Publications
- Open Access
- 9 June 2026
- Published by Elsevier in SSRN Electronic Journal
Mechanistic Evaluation of Ductile and Brittle Failure Prediction Models for SWS Bolted Connections in Balau Hardwood
Unreinforced masonry (URM) buildings in Malaysia are highly vulnerable to seismic loading due to inadequate wall–diaphragm connections, particularly in timber floor and roof systems. Existing design provisions in MS544-5 lack essential material parameters, resulting in overly conservative and potentially uneconomical designs for local hardwoods. This study experimentally investigates the behaviour of steel–wood–steel (SWS) bolted connections in Balau (Shorea spp.), a Strength Group 1 (SG1) hardwood. A total of eighteen connection configurations were tested under tension parallel to the grain, with variations in end distance and bolt spacing. The derived material properties include an average embedding strength of 52.32 MPa, a 5th percentile value of 24.11 MPa, a 5th percentile oven-dry density of 679 kg/m³, and an average moisture content of 16%. The predictive performance of the European Yield Model (EYM), Row Shear Model (RSM), and MS544-5 was evaluated. For ductile failure modes, EYM achieved an average prediction effectiveness of 62%, compared to 39% for MS544-5. For brittle row shear failures, RSM achieved 72% effectiveness using a calibrated factor of 4.9, outperforming MS544-5 (63%). The results demonstrate that mechanistically based analytical models provide substantially improved prediction reliability over current code provisions for dense tropical hardwood connections. The study further confirms that brittle row shear behaviour can be reliably modelled through calibrated row shear formulations incorporating experimentally derived characteristic material parameters. The proposed framework contributes towards the development of less conservative and more rational design approaches for timber diaphragm retrofit systems in seismic strengthening applications.
- 9 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMechanistic Evaluation of Ductile and Brittle Failure Prediction Models for SWS Bolted Connections in Balau Hardwood
Unreinforced masonry (URM) buildings in Malaysia are highly vulnerable to seismic loading due to inadequate wall–diaphragm connections, particularly in timber floor and roof systems. Existing design provisions in MS544-5 lack essential material parameters, resulting in overly conservative and potentially uneconomical designs for local hardwoods. This study experimentally investigates the behaviour of steel–wood–steel (SWS) bolted connections in Balau (Shorea spp.), a Strength Group 1 (SG1) hardwood. A total of eighteen connection configurations were tested under tension parallel to the grain, with variations in end distance and bolt spacing. The derived material properties include an average embedding strength of 52.32 MPa, a 5th percentile value of 24.11 MPa, a 5th percentile oven-dry density of 679 kg/m³, and an average moisture content of 16%. The predictive performance of the European Yield Model (EYM), Row Shear Model (RSM), and MS544-5 was evaluated. For ductile failure modes, EYM achieved an average prediction effectiveness of 62%, compared to 39% for MS544-5. For brittle row shear failures, RSM achieved 72% effectiveness using a calibrated factor of 4.9, outperforming MS544-5 (63%). The results demonstrate that mechanistically based analytical models provide substantially improved prediction reliability over current code provisions for dense tropical hardwood connections. The study further confirms that brittle row shear behaviour can be reliably modelled through calibrated row shear formulations incorporating experimentally derived characteristic material parameters. The proposed framework contributes towards the development of less conservative and more rational design approaches for timber diaphragm retrofit systems in seismic strengthening applications.
- Open Access
- 27 April 2026
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 27 (6) , 3099-3122
Axial compressive behavior of square CFST short columns with steel plate reinforcement
This study examines the axial compressive behavior of square concrete filled steel tube (CFST) short columns enhanced with steel plate reinforcement (SPR). Although CFST columns benefit from composite action, square sections exhibit reduced confinement effectiveness for the concrete core, increasing susceptibility to local buckling. While various strengthening methods are available, most of their implementation with prefabricated steel tubes is frequently impractical due to fabrication complexities that adversely affect construction efficiency. To overcome these issues, nine 100 mm $$\times $$ 100 mm $$\times $$ 300 mm square CFST short column specimens were tested experimentally under axial compression, including unreinforced, single SPR and double SPR configurations. SPR elements were spot welded internally to the steel tube walls to improve local stability with minimal fabrication complexity. Results confirm that SPR effectively delays local buckling onset, redistributes stress concentrations and enhances concrete confinement. Compared to unreinforced columns, specimens with SPR demonstrated increases in initial elastic stiffness (up to 63%), ductility (up to 39%) and ultimate axial compressive strength (up to 25%). Notably, double SPR configurations provided higher strength and energy absorption capacity, whereas single SPR delivered superior initial elastic stiffness and ductility, indicating a nonlinear performance relationship with reinforcement quantity. For analytical convenience, design equation is proposed to predict the axial compressive load capacity of square CFST short columns with SPR. These outcomes highlight SPR’s viability as a simple, efficient strengthening alternative, offering enhanced structural performance and constructability over established methods.- 27 April 2026
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 27 (6) , 3099-3122
Open AccessAxial compressive behavior of square CFST short columns with steel plate reinforcement
This study examines the axial compressive behavior of square concrete filled steel tube (CFST) short columns enhanced with steel plate reinforcement (SPR). Although CFST columns benefit from composite action, square sections exhibit reduced confinement effectiveness for the concrete core, increasing susceptibility to local buckling. While various strengthening methods are available, most of their implementation with prefabricated steel tubes is frequently impractical due to fabrication complexities that adversely affect construction efficiency. To overcome these issues, nine 100 mm $$\times $$ 100 mm $$\times $$ 300 mm square CFST short column specimens were tested experimentally under axial compression, including unreinforced, single SPR and double SPR configurations. SPR elements were spot welded internally to the steel tube walls to improve local stability with minimal fabrication complexity. Results confirm that SPR effectively delays local buckling onset, redistributes stress concentrations and enhances concrete confinement. Compared to unreinforced columns, specimens with SPR demonstrated increases in initial elastic stiffness (up to 63%), ductility (up to 39%) and ultimate axial compressive strength (up to 25%). Notably, double SPR configurations provided higher strength and energy absorption capacity, whereas single SPR delivered superior initial elastic stiffness and ductility, indicating a nonlinear performance relationship with reinforcement quantity. For analytical convenience, design equation is proposed to predict the axial compressive load capacity of square CFST short columns with SPR. These outcomes highlight SPR’s viability as a simple, efficient strengthening alternative, offering enhanced structural performance and constructability over established methods. - Open Access
- 1 March 2026
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1605 (1)
Experimental Examination of Steel Bar Reinforcements on the Compressive Responses of Square CFST Short Columns
Square concrete-filled steel tube (CFST) columns offer construction efficiency but are significantly more prone to local buckling and possess lower confinement compared to circular sections. While various strengthening schemes exist, they often pose fabrication challenges or compromise steel tube integrity. This study investigates the mechanical behaviour of square CFST short columns reinforced with internal steel bars attached via a spot-welding technique, designed to minimize residual stress and simplify fabrication. Five specimens were tested under axial compression to evaluate the effects of varying steel bar diameters (10 mm and 12 mm) and quantities (4, 8 or 12 bars). The configuration used in this study also differs from those in previous studies. Experimental results indicate that the reinforced specimens achieved ultimate axial loads ranging from 559.4 kN to 839.2 kN, representing a significant capacity increase of 47% to 121% over the unreinforced specimen. Furthermore, the spot-welded reinforcement enhanced ductility by up to 103% and total energy absorption by up to 217%. The findings conclude that this spot-welded internal reinforcement method is an effective, construction-friendly solution for delaying local buckling and improving the overall compressive performance of square CFST columns.
- 1 March 2026
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1605 (1)
Open AccessExperimental Examination of Steel Bar Reinforcements on the Compressive Responses of Square CFST Short Columns
Square concrete-filled steel tube (CFST) columns offer construction efficiency but are significantly more prone to local buckling and possess lower confinement compared to circular sections. While various strengthening schemes exist, they often pose fabrication challenges or compromise steel tube integrity. This study investigates the mechanical behaviour of square CFST short columns reinforced with internal steel bars attached via a spot-welding technique, designed to minimize residual stress and simplify fabrication. Five specimens were tested under axial compression to evaluate the effects of varying steel bar diameters (10 mm and 12 mm) and quantities (4, 8 or 12 bars). The configuration used in this study also differs from those in previous studies. Experimental results indicate that the reinforced specimens achieved ultimate axial loads ranging from 559.4 kN to 839.2 kN, representing a significant capacity increase of 47% to 121% over the unreinforced specimen. Furthermore, the spot-welded reinforcement enhanced ductility by up to 103% and total energy absorption by up to 217%. The findings conclude that this spot-welded internal reinforcement method is an effective, construction-friendly solution for delaying local buckling and improving the overall compressive performance of square CFST columns.
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Evaluating the SWS bolted connection strength of Bitis wood
Evaluating the SWS bolted connection strength of Bitis wood
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessEvaluating the SWS bolted connection strength of Bitis wood
Evaluating the SWS bolted connection strength of Bitis wood