Norazzlina M. Sa’don
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Norazzlina M. Sa’don has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Razak Abdul Karim
Universiti Malaysia Sarawak
11 shared publications - Pierre Quenneville
Dept. of Civil and Environmental Engineering Univ. of Auckland Auckland New Zealand
4 shared publications - Michael John Pender
Department of Civil and Environmental Engineering, University of Auckland, Auckland, New Zealand
3 shared publications - Rolando. P. Orense
Department of Civil and Environmental Engineering University of Auckland Auckland New Zealand
3 shared publications - Abdul Azim Abdullah
Department of Civil Engineering, Universiti Malaysia Sarawak, Kota Samarahan, Malaysia
2 shared publications - Nur Liza Rahim
University Malaysia Perlis, Faculty of Civil Engineering & Technology, Kampus Pusat Pengajian Jejawi 3, 02600 Arau, Perlis, Malaysia
2 shared publications
Latest Publications
- Open Access
- 9 June 2026
- Published by Elsevier in SSRN Electronic Journal
Mechanistic Evaluation of Ductile and Brittle Failure Prediction Models for SWS Bolted Connections in Balau Hardwood
Unreinforced masonry (URM) buildings in Malaysia are highly vulnerable to seismic loading due to inadequate wall–diaphragm connections, particularly in timber floor and roof systems. Existing design provisions in MS544-5 lack essential material parameters, resulting in overly conservative and potentially uneconomical designs for local hardwoods. This study experimentally investigates the behaviour of steel–wood–steel (SWS) bolted connections in Balau (Shorea spp.), a Strength Group 1 (SG1) hardwood. A total of eighteen connection configurations were tested under tension parallel to the grain, with variations in end distance and bolt spacing. The derived material properties include an average embedding strength of 52.32 MPa, a 5th percentile value of 24.11 MPa, a 5th percentile oven-dry density of 679 kg/m³, and an average moisture content of 16%. The predictive performance of the European Yield Model (EYM), Row Shear Model (RSM), and MS544-5 was evaluated. For ductile failure modes, EYM achieved an average prediction effectiveness of 62%, compared to 39% for MS544-5. For brittle row shear failures, RSM achieved 72% effectiveness using a calibrated factor of 4.9, outperforming MS544-5 (63%). The results demonstrate that mechanistically based analytical models provide substantially improved prediction reliability over current code provisions for dense tropical hardwood connections. The study further confirms that brittle row shear behaviour can be reliably modelled through calibrated row shear formulations incorporating experimentally derived characteristic material parameters. The proposed framework contributes towards the development of less conservative and more rational design approaches for timber diaphragm retrofit systems in seismic strengthening applications.
- 9 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMechanistic Evaluation of Ductile and Brittle Failure Prediction Models for SWS Bolted Connections in Balau Hardwood
Unreinforced masonry (URM) buildings in Malaysia are highly vulnerable to seismic loading due to inadequate wall–diaphragm connections, particularly in timber floor and roof systems. Existing design provisions in MS544-5 lack essential material parameters, resulting in overly conservative and potentially uneconomical designs for local hardwoods. This study experimentally investigates the behaviour of steel–wood–steel (SWS) bolted connections in Balau (Shorea spp.), a Strength Group 1 (SG1) hardwood. A total of eighteen connection configurations were tested under tension parallel to the grain, with variations in end distance and bolt spacing. The derived material properties include an average embedding strength of 52.32 MPa, a 5th percentile value of 24.11 MPa, a 5th percentile oven-dry density of 679 kg/m³, and an average moisture content of 16%. The predictive performance of the European Yield Model (EYM), Row Shear Model (RSM), and MS544-5 was evaluated. For ductile failure modes, EYM achieved an average prediction effectiveness of 62%, compared to 39% for MS544-5. For brittle row shear failures, RSM achieved 72% effectiveness using a calibrated factor of 4.9, outperforming MS544-5 (63%). The results demonstrate that mechanistically based analytical models provide substantially improved prediction reliability over current code provisions for dense tropical hardwood connections. The study further confirms that brittle row shear behaviour can be reliably modelled through calibrated row shear formulations incorporating experimentally derived characteristic material parameters. The proposed framework contributes towards the development of less conservative and more rational design approaches for timber diaphragm retrofit systems in seismic strengthening applications.
- Open Access
- 31 October 2025
- Published by UNIMAS Publisher in Journal of Applied Science & Process Engineering
- Vol. 12 (2) , 206-218
Landslide Susceptibility Mapping of Western Sarawak via Artificial Neural Network
Landslides are the third most frequent form of natural disaster in Malaysia, following floods and storms. It can cause significant damage to anything in its path, depending on the size and velocity of its debris. Due to the danger that it poses, determining the susceptibility of an area to landslides is a crucial step in risk mitigation. Landslide occurrences are dependent on the numerous environmental variables, which can provide information on the level of susceptibility of other locations with similar variables. To quantify the significance of each variable to landslide occurrence, a supervised Machine Learning model – an Artificial Neural Network was developed for this study. Furthermore, landslide occurrences have been associated with the disturbance of natural slopes to accommodate development, which was the main reason behind the selection of Western Sarawak as the area of interest in this study. The model was developed to understand and make landslide susceptibility predictions based on aspect, curvature, elevation, lithology type, rainfall intensity, slope angle, soil type, and TWI. Evaluating the area under the curve score and recall for the model revealed that, based on the available inputs, the model performed well with a score of 1 and 0.99, respectively.
- 31 October 2025
- Published by UNIMAS Publisher in Journal of Applied Science & Process Engineering
- Vol. 12 (2) , 206-218
Open AccessLandslide Susceptibility Mapping of Western Sarawak via Artificial Neural Network
Landslides are the third most frequent form of natural disaster in Malaysia, following floods and storms. It can cause significant damage to anything in its path, depending on the size and velocity of its debris. Due to the danger that it poses, determining the susceptibility of an area to landslides is a crucial step in risk mitigation. Landslide occurrences are dependent on the numerous environmental variables, which can provide information on the level of susceptibility of other locations with similar variables. To quantify the significance of each variable to landslide occurrence, a supervised Machine Learning model – an Artificial Neural Network was developed for this study. Furthermore, landslide occurrences have been associated with the disturbance of natural slopes to accommodate development, which was the main reason behind the selection of Western Sarawak as the area of interest in this study. The model was developed to understand and make landslide susceptibility predictions based on aspect, curvature, elevation, lithology type, rainfall intensity, slope angle, soil type, and TWI. Evaluating the area under the curve score and recall for the model revealed that, based on the available inputs, the model performed well with a score of 1 and 0.99, respectively.
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Evaluating the SWS bolted connection strength of Bitis wood
Evaluating the SWS bolted connection strength of Bitis wood
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessEvaluating the SWS bolted connection strength of Bitis wood
Evaluating the SWS bolted connection strength of Bitis wood
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17 (6) , 79-91
EFFECTIVENESS VALIDATION ON EXISTING DESIGN EQUATIONS FOR THE SUSTAINABLE DESIGN OF MASONRY BUILDING RETROFITS
Due to the unsatisfactory performance of MS544-5 in estimating the design capacity of bolted timber connections, this present study was initiated to validate the existing predictive equations used by the Malaysian Standard (MS544-5). An evaluation of the European Yield Model (EYM) equation was also done to provide an optimal design equation for the bolted connection design in local hardwood. To verify these two sets of equations, a series of bolted timber connection tests was conducted on Nyatoh hardwood. Nyatoh was chosen as its strength makes it ideal for use as structural timbers, either as roof rafters or floor joists in masonry building constructions. The bolted timber connection tests conducted involved eight types of bolt configurations and the tests on each configuration was done in sets of 10 specimens. The experimental values obtained were then compared with the predictive equations of MS544-5 and EYM to examine their effectiveness. From the comparison, it was found that the prediction values given by MS544-5 were overly conservative with an average effective ratio of 0.34 while the EYM had an average effective ratio of 1.09. Thus, the use of EYM equations was recommended for the sustainable retrofit design development of Malaysian masonry buildings.
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17 (6) , 79-91
EFFECTIVENESS VALIDATION ON EXISTING DESIGN EQUATIONS FOR THE SUSTAINABLE DESIGN OF MASONRY BUILDING RETROFITS
Due to the unsatisfactory performance of MS544-5 in estimating the design capacity of bolted timber connections, this present study was initiated to validate the existing predictive equations used by the Malaysian Standard (MS544-5). An evaluation of the European Yield Model (EYM) equation was also done to provide an optimal design equation for the bolted connection design in local hardwood. To verify these two sets of equations, a series of bolted timber connection tests was conducted on Nyatoh hardwood. Nyatoh was chosen as its strength makes it ideal for use as structural timbers, either as roof rafters or floor joists in masonry building constructions. The bolted timber connection tests conducted involved eight types of bolt configurations and the tests on each configuration was done in sets of 10 specimens. The experimental values obtained were then compared with the predictive equations of MS544-5 and EYM to examine their effectiveness. From the comparison, it was found that the prediction values given by MS544-5 were overly conservative with an average effective ratio of 0.34 while the EYM had an average effective ratio of 1.09. Thus, the use of EYM equations was recommended for the sustainable retrofit design development of Malaysian masonry buildings.
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17 (6) , 172-181
STRENGTH PERFORMANCE ON STABILISATION OF SARAWAK SOILS USING GEOCRETE® TECHNOLOGY
This paper presents a study on the stabilisation performance of Sarawak soils using GeoCrete® Technology. GeoCrete is used for stabilisation treatments where the soils are treated with ordinary Portland cement (OPC) as a binder and GeoCrete® powder (GCP) as an alkaline additive to improve their strength and elasticity. The use of GCP in soil stabilisation was proven to improve the compressive strength of soils by more than twice the initial strength after 28 days of being treated, with the treatments carried out on three identified soils: Clay, silt and sand. This technique has been successfully implemented on farm roads, rural roads and highways. Thus, further investigation of stabilisation with GCP was conducted on peat, which is known as a material with high permeability and low bearing capacity behaviour. The peat samples collected are mixed at a designated percentage of OPC and 2% of GCP. The compacted and treated peat samples with OPC and GCP were prepared at the optimum moisture content, mixed thoroughly to a uniform condition using a laboratory mixer and air cured for 7 and 28 days in a single batch. The results showed that peat stabilised with GCP has an average of more than 40% of the unconfined compressive strength, qu value after 28 days of curing when compared with peat at the natural state.
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17 (6) , 172-181
STRENGTH PERFORMANCE ON STABILISATION OF SARAWAK SOILS USING GEOCRETE® TECHNOLOGY
This paper presents a study on the stabilisation performance of Sarawak soils using GeoCrete® Technology. GeoCrete is used for stabilisation treatments where the soils are treated with ordinary Portland cement (OPC) as a binder and GeoCrete® powder (GCP) as an alkaline additive to improve their strength and elasticity. The use of GCP in soil stabilisation was proven to improve the compressive strength of soils by more than twice the initial strength after 28 days of being treated, with the treatments carried out on three identified soils: Clay, silt and sand. This technique has been successfully implemented on farm roads, rural roads and highways. Thus, further investigation of stabilisation with GCP was conducted on peat, which is known as a material with high permeability and low bearing capacity behaviour. The peat samples collected are mixed at a designated percentage of OPC and 2% of GCP. The compacted and treated peat samples with OPC and GCP were prepared at the optimum moisture content, mixed thoroughly to a uniform condition using a laboratory mixer and air cured for 7 and 28 days in a single batch. The results showed that peat stabilised with GCP has an average of more than 40% of the unconfined compressive strength, qu value after 28 days of curing when compared with peat at the natural state.
- Open Access
- 10 February 2022
- Published by North Atlantic University Union (NAUN) in International Journal of Mechanics
- Vol. 16, 6-14
Design Optimization of the Bolted Connection Loaded Parallel to the Timber Grain for Masonry Building Retrofits
The experimental results of timber bolted connection tests for the purpose of optimizing the use of current design standard are presented. The test was conducted to investigate the structural performance of bolted connections loaded parallel to the timber grain. Both ductile and brittle failure modes were investigated to identify the governing parameters that affect the types of failures. The Meraka hardwood was chosen because it was found to be commonly used in the construction of the structural components of floor and roof diaphragms in Malaysia unreinforced masonry (URM) buildings. From this study, a wood database can be established for assisting the design engineers in developing the retrofitting technique of the building, especially the timber diaphragm joint part of the wall-diaphragm connections. Eighteen characteristics of steel-wood-steel (SWS) with a single row bolted joints were tested in tension, whereas ten specimens were prepared for each connection group. From the results obtained, it can be observed that the current timber design code is far too conservative compared to the optimized design proposed in this paper.
- 10 February 2022
- Published by North Atlantic University Union (NAUN) in International Journal of Mechanics
- Vol. 16, 6-14
Open AccessDesign Optimization of the Bolted Connection Loaded Parallel to the Timber Grain for Masonry Building Retrofits
The experimental results of timber bolted connection tests for the purpose of optimizing the use of current design standard are presented. The test was conducted to investigate the structural performance of bolted connections loaded parallel to the timber grain. Both ductile and brittle failure modes were investigated to identify the governing parameters that affect the types of failures. The Meraka hardwood was chosen because it was found to be commonly used in the construction of the structural components of floor and roof diaphragms in Malaysia unreinforced masonry (URM) buildings. From this study, a wood database can be established for assisting the design engineers in developing the retrofitting technique of the building, especially the timber diaphragm joint part of the wall-diaphragm connections. Eighteen characteristics of steel-wood-steel (SWS) with a single row bolted joints were tested in tension, whereas ten specimens were prepared for each connection group. From the results obtained, it can be observed that the current timber design code is far too conservative compared to the optimized design proposed in this paper.
- 8 September 2021
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 411, 121-133
Effect of Waste Tire Reinforcement with and without Cement Additives on Peat Strength Improvement
This paper presents the peat ground improvement techniques using waste-tire as a fibre reinforced material. In this study, two sizes of the waste-tire are chosen, which are 0.05 mm and 1-3 mm, respectively. The collected peat is classified as Sapric peat with the degree of decomposition of H7 based on von Post classification with high moisture content of 400% was recorded. The Sapric peat is treated with the waste-tire at designated percentages of 5%, 10% and 15% with the addition of 5% of cement acting as a binder. The untreated and treated peat without and with cement content are compacted at the optimum moisture content for both the Unconfined Compressive Strength (UCS) test and Direct Shear Box Test. The specimens were air-cured for 7, 28, 56, and 90 days. Hypothetically, higher percentages of rubber improve the shear stress value of the treated peat. According to the results the finer size (0.05mm) of the tire produces a higher shear stress, which may due the finer sizes of the waste-tire filled the void between the soil particles. Further, from the 90 days of curing UCS results, there is a significant increase in compressive strength with the increase percentage of the waste-tire peat mixed samples. In summary, soil stabilized by the scrap-tire is believed to decrease the optimum moisture content and the maximum dry densities, but it helps in increasing the unconfined compressive strength value. Stabilizing by using the tire wastes not only increasing the strength of the soil, but it also helps in reducing the disposal problems.
- 8 September 2021
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 411, 121-133
Effect of Waste Tire Reinforcement with and without Cement Additives on Peat Strength Improvement
This paper presents the peat ground improvement techniques using waste-tire as a fibre reinforced material. In this study, two sizes of the waste-tire are chosen, which are 0.05 mm and 1-3 mm, respectively. The collected peat is classified as Sapric peat with the degree of decomposition of H7 based on von Post classification with high moisture content of 400% was recorded. The Sapric peat is treated with the waste-tire at designated percentages of 5%, 10% and 15% with the addition of 5% of cement acting as a binder. The untreated and treated peat without and with cement content are compacted at the optimum moisture content for both the Unconfined Compressive Strength (UCS) test and Direct Shear Box Test. The specimens were air-cured for 7, 28, 56, and 90 days. Hypothetically, higher percentages of rubber improve the shear stress value of the treated peat. According to the results the finer size (0.05mm) of the tire produces a higher shear stress, which may due the finer sizes of the waste-tire filled the void between the soil particles. Further, from the 90 days of curing UCS results, there is a significant increase in compressive strength with the increase percentage of the waste-tire peat mixed samples. In summary, soil stabilized by the scrap-tire is believed to decrease the optimum moisture content and the maximum dry densities, but it helps in increasing the unconfined compressive strength value. Stabilizing by using the tire wastes not only increasing the strength of the soil, but it also helps in reducing the disposal problems.
- 8 September 2021
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 411, 109-120
Strength Enhancement of Fibre Reinforced Peat with Fly Ash as Stabilized Subgrade Layer
High content of organic matter and fibre within peat results in a high degree of porosity; causing peat to have low bearing capacity. This study focuses on the application of nylon fibre as reinforcing material with fly ash as the chemical stabilizer to enhance the strength of the peat. The standard proctor tests were conducted to obtain the optimum moisture content (OMC) for all samples in which these OMC is then used for sample preparation of both the Unconfined Compressive Strength (UCS) tests and the California Bearing Ratio (CBR) tests. Samples for this study were categorized into control samples and modified samples for comparison purposes. Additives that were being used in this study are 5% cement, 5% nylon fibre and 10%, 15%, and 20% fly ash. For UCS test, the samples were cured for 7, 14, 28 and 56 days, whereas only 7 days of curing for CBR test. Throughout the study, improvements of strength were observed where sample added with 5% cement, 5% nylon fibre and 10% fly ash recorded the highest compressive strength value, of 123.71 kN/m2. As for CBR test, all samples exceeded the minimum requirement of 12% CBR value for subgrade design recommended by JKR Malaysia with the highest CBR value obtained from samples added with 5% cement and 10% fly ash. The CBR values were 43.85% and 43.70% for unsoaked and soaked condition, respectively.
- 8 September 2021
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 411, 109-120
Strength Enhancement of Fibre Reinforced Peat with Fly Ash as Stabilized Subgrade Layer
High content of organic matter and fibre within peat results in a high degree of porosity; causing peat to have low bearing capacity. This study focuses on the application of nylon fibre as reinforcing material with fly ash as the chemical stabilizer to enhance the strength of the peat. The standard proctor tests were conducted to obtain the optimum moisture content (OMC) for all samples in which these OMC is then used for sample preparation of both the Unconfined Compressive Strength (UCS) tests and the California Bearing Ratio (CBR) tests. Samples for this study were categorized into control samples and modified samples for comparison purposes. Additives that were being used in this study are 5% cement, 5% nylon fibre and 10%, 15%, and 20% fly ash. For UCS test, the samples were cured for 7, 14, 28 and 56 days, whereas only 7 days of curing for CBR test. Throughout the study, improvements of strength were observed where sample added with 5% cement, 5% nylon fibre and 10% fly ash recorded the highest compressive strength value, of 123.71 kN/m2. As for CBR test, all samples exceeded the minimum requirement of 12% CBR value for subgrade design recommended by JKR Malaysia with the highest CBR value obtained from samples added with 5% cement and 10% fly ash. The CBR values were 43.85% and 43.70% for unsoaked and soaked condition, respectively.
- 8 September 2021
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 411, 157-168
Artificial Neural Network (ANN) Model for Shear Strength of Soil Prediction
Geotechnical structures, design of embankment, earth and rock fill dam, tunnels, and slope stability require further attention in determining the shear strength of soil and other parameters that govern the result. The shear strength of soil commonly obtained by conducting laboratory testing such as Unconfined Compression Strength (UCS) Test and Unconsolidated Undrained (UU) Test. However, random errors and systematic errors can occur during experimental works and caused the findings imprecise. Besides, the laboratory test also consuming a lot of time and some of them are quite costly. Therefore, soft computational tools are developed to improve the accuracy of the results and time effectively when compared to conventional method. In this study, Artificial Neural Network (ANN) was employed to develop a predictive model to correlate the moisture content (MC), liquid limit (LL), plastic limit (PL), and liquidity index (LI) of cohesive soil with the undrained shear strength of soil. A total of 10 databases was developed by using MATLAB 7.0 - matrix laboratory with 318 of UCS tests and 451 of UU tests which are collected from the verified site investigation (SI) report, respectively. All the SI reports collected were conducted in Sarawak, Malaysia. The datasets were split into ratio of 3:1:1 which is 60:20:20 (training: validation: testing) with one hidden layer and eight hidden neurons. The input parameter of Liquidity index (LI) has shown the highest R-value (regression coefficient) which are 0.926 and 0.904 for UCS and UU model, respectively. In addition, the predictive models were tested and compare with the predicted and observed cohesion obtained from the collected experimental results. In summary, the ANN has the feasibility to be used as a predictive tool in estimating the shear strength of the soil.
- 8 September 2021
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 411, 157-168
Artificial Neural Network (ANN) Model for Shear Strength of Soil Prediction
Geotechnical structures, design of embankment, earth and rock fill dam, tunnels, and slope stability require further attention in determining the shear strength of soil and other parameters that govern the result. The shear strength of soil commonly obtained by conducting laboratory testing such as Unconfined Compression Strength (UCS) Test and Unconsolidated Undrained (UU) Test. However, random errors and systematic errors can occur during experimental works and caused the findings imprecise. Besides, the laboratory test also consuming a lot of time and some of them are quite costly. Therefore, soft computational tools are developed to improve the accuracy of the results and time effectively when compared to conventional method. In this study, Artificial Neural Network (ANN) was employed to develop a predictive model to correlate the moisture content (MC), liquid limit (LL), plastic limit (PL), and liquidity index (LI) of cohesive soil with the undrained shear strength of soil. A total of 10 databases was developed by using MATLAB 7.0 - matrix laboratory with 318 of UCS tests and 451 of UU tests which are collected from the verified site investigation (SI) report, respectively. All the SI reports collected were conducted in Sarawak, Malaysia. The datasets were split into ratio of 3:1:1 which is 60:20:20 (training: validation: testing) with one hidden layer and eight hidden neurons. The input parameter of Liquidity index (LI) has shown the highest R-value (regression coefficient) which are 0.926 and 0.904 for UCS and UU model, respectively. In addition, the predictive models were tested and compare with the predicted and observed cohesion obtained from the collected experimental results. In summary, the ANN has the feasibility to be used as a predictive tool in estimating the shear strength of the soil.
- Open Access
- 1 May 2021
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1030, 124-137
Comparative Strength of Fibre Reinforced Peat and Clayey-Silt by Using Shredded Scrap-Tire
The strength comparison of fibre reinforced peat and clayey-silt for the compacted sub-grade by using the fibre reinforcement technique from the scrap tire is presented. The scrap tires are extracted and shredded into a standard size, i.e., rubber-chip, rubber-crumb, rubber-powder and fibre-polyester for the consistency and homogeneity of the design mix. In this study, two types of fibres are used, which are fibre polyester and rubber crumb. The fibres at various designated percentage are mixed with the clayey-silt and peat with the addition of a minimum 5% cement content as a binder to achieve the targeted strength. The specimens were prepared by compacting at the optimum moisture content and maximum dry density. The compacted treated specimens were prepared and air cured for 7 and 28 days in room temperature (23C to 26C). In evaluating the strength and durability effect of fibres between the untreated (no fibres) and treated specimens (with fibres and cement), the Unconfined Compression Strength (UCS) and California Bearing Ratio (CBR) tests are executed. The findings indicate that the shear strength increases with the curing period. The addition of fibre-polyester and shredded rubber-crumb exhibits an increment in the contact area and bonding between the fibre reinforced materials and soil particles, which then significantly improved the compressive strength of the design mix.
- 1 May 2021
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1030, 124-137
Open AccessComparative Strength of Fibre Reinforced Peat and Clayey-Silt by Using Shredded Scrap-Tire
The strength comparison of fibre reinforced peat and clayey-silt for the compacted sub-grade by using the fibre reinforcement technique from the scrap tire is presented. The scrap tires are extracted and shredded into a standard size, i.e., rubber-chip, rubber-crumb, rubber-powder and fibre-polyester for the consistency and homogeneity of the design mix. In this study, two types of fibres are used, which are fibre polyester and rubber crumb. The fibres at various designated percentage are mixed with the clayey-silt and peat with the addition of a minimum 5% cement content as a binder to achieve the targeted strength. The specimens were prepared by compacting at the optimum moisture content and maximum dry density. The compacted treated specimens were prepared and air cured for 7 and 28 days in room temperature (23C to 26C). In evaluating the strength and durability effect of fibres between the untreated (no fibres) and treated specimens (with fibres and cement), the Unconfined Compression Strength (UCS) and California Bearing Ratio (CBR) tests are executed. The findings indicate that the shear strength increases with the curing period. The addition of fibre-polyester and shredded rubber-crumb exhibits an increment in the contact area and bonding between the fibre reinforced materials and soil particles, which then significantly improved the compressive strength of the design mix.