YDYoung-Woo Do

Young-Woo Do

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Young-Woo Do has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Simulation-Based Evaluation of Vision-Based Adaptive Conveyor Speed Control Using Reel-Synchronous Onion Counting in a Self-Propelled Onion Collector

    by Hyeon-Seo Yoon, Yi-Seo Min, Young-Woo Do, Seung-Min Baek, Seung-Yun Baek, Deok-Hyeon Ko, Yong-Joo Kim, Wan-Soo Kim

    The stream of onions entering a self-propelled onion collector varies with field conditions, feeding density, and the transient lifting behavior of the onion–soil mass, whereas the collection conveyor is conventionally operated at a fixed speed, wasting hydraulic energy. This study proposes and evaluates, through field-calibrated simulation, a vision-based feedforward conveyor speed control framework that couples reel-synchronous onion counting with variable-displacement pump control. To mitigate the periodic occlusion caused by the compact dual-conveyor structure, a frame-selection method synchronized with the detected conveyor position was implemented, and a YOLOv8n detector was trained and evaluated on 314 images extracted from 32 indoor and field source videos partitioned at the source-video level. On the independent test subset, the model achieved precision, recall, and mAP@0.5 of 0.952, 0.944, and 0.959, and the proposed counting method maintained count recovery ratios above 95% across all engine speeds in 45 independent field trials, outperforming fixed-period sampling and tracking-based baselines by 6.6 and 3.8 percentage points, respectively. An AMESim model of the fixed-displacement hydraulic system was calibrated and shown to be consistent with field measurements and was then used to evaluate the variable-displacement configuration. Net conveyor-related fuel savings (engine no-load consumption subtracted) were estimated at 14.3–18.7% under the field-identified constant transmission efficiency, with conservative estimates of 11.5–16.9% when partial-displacement efficiency losses were accounted for through an anchored loss model. These results demonstrate the feasibility of vision-based feedforward conveyor speed control and its potential for energy savings in bulb-crop collection.

  • Open Access

    Simulation of Engine Power Requirement and Fuel Consumption in a Self-Propelled Crop Collector

    by Yi-Seo Min, Young-Woo Do, Youngtae Yun, Sang-Hee Lee, Seung-Gwi Kwon, Wan-Soo Kim

    This study attempted to develop and validate a data-driven simulation model that integrates field-measured data to assess the power requirement and fuel consumption characteristics of a self-propelled collector. The collector is a hydrostatic transmission-based, crawler-type platform designed for garlic and onion harvesting, equipped with multiple hydraulic subsystems for collection and sorting. During field experiments, the power requirements of each subsystem and fuel flow rate were recorded, and Willans line method was applied to estimate engine power and subsystem power transmission efficiencies. Because many small agricultural machines do not support electronically instrumented engines (e.g., CAN-bus/ECU-based measurements), the proposed model was formulated as a data-driven, low-order representation derived from on-site measurements rather than a full physics-based model. Using the identified parameters, the simulation framework predicts engine power and fuel efficiency under various operating conditions. The simulation results exhibited high agreement with field data, achieving R2 and mean absolute percentage error values of 0.935–0.981 and 1.79–4.18%, respectively, confirming reliable reproduction of real field performance. A comprehensive analysis of the simulation results revealed that both engine speed and travel speed significantly influence power distribution and fuel rate, while also indicating that hydraulic working power is the dominant contributor to total power demand at higher engine speeds. These findings provide practical guidance for improving the fuel efficiency of compact self-propelled collectors.


  • Open Access

    Evaluation of Power Requirement for a Self-Propelled Garlic Collector Based on Load Experiments and Variable Impact Analysis Under Various Operating Conditions

    by Young-Woo Do, Yi-Seo Min, Seok-Pyo Moon, Young-Jo Nam, Seung-Gwi Kwon, Wan-Soo Kim

    Garlic is a labor-intensive underground crop in Republic of Korea, where harvesting and collection require substantial manual work. Although self-propelled garlic collectors have been introduced, most were developed empirically, and quantitative evaluations of their load characteristics and power requirements under field conditions remain limited. This study quantifies the power requirements of the driving, collection, and transport parts of a self-propelled garlic collector and examines the effects of driving speed, collecting speed, transporting speed, and working depth. A field measurement system was developed to record torque, rotational speed, flow rate, and pressure, and these data were used to calculate the power requirement of each major component and the overall machine. Results showed that driving speed was the dominant factor affecting total power use, as the driving part displayed a clear increase with higher speeds. In contrast, the collection and transport parts exhibited only minor changes, and the influence of working depth was negligible. The maximum total power requirement was 12.28 kW, about 30% of the rated engine power of 40.2 kW, indicating that engine capacity exceeded actual requirement. These findings provide quantitative insights into self-propelled garlic collectors and essential data for future studies on engine downsizing and power transmission design.