Zhuang Zhi Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhuang Zhi Sun has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Fuchen Wang
2 shared publicationsGuangsuo Yu
2 shared publications- Douglas Hungwe
Department of Transdisciplinary Science and Engineering, School of Environment and Society, Tokyo Institute of Technology, G5-13, 4259, Nagatsuta, Midori-ku, Yokohama 226-8503, Japan
1 shared publication - Gang Zhao
Harbin Engineering University
1 shared publication - Gang Zhao
Wuhan University of Science and Technology
1 shared publication Kai Dong
Institute of Clean Coal Technology East China University of Science and Technology Shanghai People's Republic of China
1 shared publication
Latest Publications
- Open Access
- 4 July 2026
- Published by Elsevier in Engineering
- Vol. 64, 347-359
Spatial Assessment of Rural Energy Demand and Straw Resource Availability
- 4 July 2026
- Published by Elsevier in Engineering
- Vol. 64, 347-359
Open AccessSpatial Assessment of Rural Energy Demand and Straw Resource Availability
- 27 February 2026
- Published by Wiley in AIChE Journal
Understanding oxygen carrier‐support interactions in looping hydrogen production
Chemical looping hydrogen production (CLHP) offers a promising route for continuous high‐purity H 2 generation with integrated carbon capture. Fe 2 O 3 is a commonly used oxygen carrier (OC) in CLHP but is limited by moderate reactivity and low stability. Employing ionic conductor as OC support has been proposed to overcome these limitations, yet the underlying mechanisms, particularly the OC‐support interactions, remain unclear. Here, we investigated CaTiO 3 as a model support and Al 2 O 3 as a reference to elucidate the origins of enhanced performances. The CaTiO 3 ‐Fe 2 O 3 composite exhibited a substantially high reduction rate (~4 times), significantly increased H 2 yield (50% ~ 280%), and enhanced stability over multi redox cycles compared to the reference, comparable to Fe 2 O 3 supported on well‐established ionic conductors. The improved performance is ascribed to increased oxide ion mobility within the bulk Fe 2 O 3 . DFT calculations revealed that the oxide ion mobility was synergistically driven by low‐concentration Ti doping and CaTiO 3 induced tensile strain.
- 27 February 2026
- Published by Wiley in AIChE Journal
Understanding oxygen carrier‐support interactions in looping hydrogen production
Chemical looping hydrogen production (CLHP) offers a promising route for continuous high‐purity H 2 generation with integrated carbon capture. Fe 2 O 3 is a commonly used oxygen carrier (OC) in CLHP but is limited by moderate reactivity and low stability. Employing ionic conductor as OC support has been proposed to overcome these limitations, yet the underlying mechanisms, particularly the OC‐support interactions, remain unclear. Here, we investigated CaTiO 3 as a model support and Al 2 O 3 as a reference to elucidate the origins of enhanced performances. The CaTiO 3 ‐Fe 2 O 3 composite exhibited a substantially high reduction rate (~4 times), significantly increased H 2 yield (50% ~ 280%), and enhanced stability over multi redox cycles compared to the reference, comparable to Fe 2 O 3 supported on well‐established ionic conductors. The improved performance is ascribed to increased oxide ion mobility within the bulk Fe 2 O 3 . DFT calculations revealed that the oxide ion mobility was synergistically driven by low‐concentration Ti doping and CaTiO 3 induced tensile strain.
- 1 February 2016
- Published by Trans Tech Publications, Ltd. in Journal of Biomimetics, Biomaterials and Biomedical Engineering
- Vol. 26, 13-18
Fabrication of Bionic Linear Actuator and Application Study Based on 3D Printing
In this manuscript, a bionic linear actuator was developed base on the ionic actuator: ionicpolymer metal composites, and the mainly fabrication method was presented in the currentinvestigation. Subsequently, a bionic robot was developed using 3D printing technique to fabricatethe skeleton structure and the presented Bi-IPMC(assembled by two segmented IPMC strip) linearactuator as the driving power. After a mathematical model of bionic robot, a experimented bionicrobot was manufactured to investigate. The results founded that our bionic robot behaved a maximumbounce height arrived at 22mm under applied 5V direct current, and the bounce height can keep onthe values of 18mm over the applied voltage of 4V.
- 1 February 2016
- Published by Trans Tech Publications, Ltd. in Journal of Biomimetics, Biomaterials and Biomedical Engineering
- Vol. 26, 13-18
Fabrication of Bionic Linear Actuator and Application Study Based on 3D Printing
In this manuscript, a bionic linear actuator was developed base on the ionic actuator: ionicpolymer metal composites, and the mainly fabrication method was presented in the currentinvestigation. Subsequently, a bionic robot was developed using 3D printing technique to fabricatethe skeleton structure and the presented Bi-IPMC(assembled by two segmented IPMC strip) linearactuator as the driving power. After a mathematical model of bionic robot, a experimented bionicrobot was manufactured to investigate. The results founded that our bionic robot behaved a maximumbounce height arrived at 22mm under applied 5V direct current, and the bounce height can keep onthe values of 18mm over the applied voltage of 4V.
- 1 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 889-890, 938-941
Forward Kinematic Modeling and Simulation of Ionic Polymer Metal Composites (IPMC) Actuators for Bionic Knee Joint
Ionic Polymer Composite Material (IPMC) is a flexible material and has revealed many advantages to encourage the scientists and researchers to investigate its characteristics for practical applications in various fields. The ongoing research can be divided into two branches. One deals with the improvement of the material properties to make it more useful and reliable while the other involves the exploration of new application areas. In this paper, Firstly, a new application of IPMC is suggested to actuate a rigid link that can mimic a bionic knee joint for a grass hopper manipulator. Secondly, forward kinematic model is proposed for the manipulator by employing geometric coordinate system method. Lastly, wolfram mathematica software is employed for the simulation of the model. The simulation results based on the model are found very encouraging to lure the article team to carry on the research idea for manufacturing and testing for the comparison of both types of results.
- 1 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 889-890, 938-941
Forward Kinematic Modeling and Simulation of Ionic Polymer Metal Composites (IPMC) Actuators for Bionic Knee Joint
Ionic Polymer Composite Material (IPMC) is a flexible material and has revealed many advantages to encourage the scientists and researchers to investigate its characteristics for practical applications in various fields. The ongoing research can be divided into two branches. One deals with the improvement of the material properties to make it more useful and reliable while the other involves the exploration of new application areas. In this paper, Firstly, a new application of IPMC is suggested to actuate a rigid link that can mimic a bionic knee joint for a grass hopper manipulator. Secondly, forward kinematic model is proposed for the manipulator by employing geometric coordinate system method. Lastly, wolfram mathematica software is employed for the simulation of the model. The simulation results based on the model are found very encouraging to lure the article team to carry on the research idea for manufacturing and testing for the comparison of both types of results.