Wen-Li Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Wen-Li Wu has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Christopher L. Soles
Material Measurement Laboratory National Institute of Standards and Technology Gaithersburg Maryland USA
4 shared publications - Eric K. Lin
National Institute of Standards and Technology
4 shared publications - Ronald L. Jones
National Institute of Standards and Technology
3 shared publications Hae-Jeong Lee
Polymers Division, National Institute of Standards and Technology, Gaithersburg, Maryland 20899, United States
2 shared publicationsMarie Angelopoulos
IBM Thomas J. Watson Research Ctr. (USA)
2 shared publications- Aaron M. Forster
Material Measurement Laboratory
1 shared publication
Latest Publications
- Open Access
- 1 February 2019
- Published by National Institute of Standards and Technology (NIST) in Journal of Research of the National Institute of Standards and Technology
- Vol. 124, 1-3
X-ray Metrology for the SemiconductorIndustry Tutorial
The semiconductor industry is in need of new, in-line dimensional metrology methods with higherspatial resolution for characterizing their next generation nanodevices. The purpose of this short course is to train the semiconductor industry on the NIST-developed critical dimension small angle X-ray scattering (CDSAXS) method. The topics will include both data processing and instrumentation. The short course will also provide an opportunity for discussion of the requirements for CDSAXS and the necessary improvements in X-ray source technology. Expected audience include semiconductor manufacturers, equipment manufacturers, and component manufacturers. The presentations were made at “X-ray Metrology for the Semiconductor Industry” short course at the National Institute of Standards and Technology on Aug. 25, 2016.
- 1 February 2019
- Published by National Institute of Standards and Technology (NIST) in Journal of Research of the National Institute of Standards and Technology
- Vol. 124, 1-3
Open AccessX-ray Metrology for the SemiconductorIndustry Tutorial
The semiconductor industry is in need of new, in-line dimensional metrology methods with higherspatial resolution for characterizing their next generation nanodevices. The purpose of this short course is to train the semiconductor industry on the NIST-developed critical dimension small angle X-ray scattering (CDSAXS) method. The topics will include both data processing and instrumentation. The short course will also provide an opportunity for discussion of the requirements for CDSAXS and the necessary improvements in X-ray source technology. Expected audience include semiconductor manufacturers, equipment manufacturers, and component manufacturers. The presentations were made at “X-ray Metrology for the Semiconductor Industry” short course at the National Institute of Standards and Technology on Aug. 25, 2016.
- 8 November 2012
- Published by American Chemical Society (ACS) in ACS Macro Letters
- Vol. 1 (11) , 1347-1351
Imaging the Molecular Structure of Polyethylene Blends with Broadband Coherent Raman Microscopy
Polyethylene (PE) has been widely used in a myriad of consumer products and critical infrastructure products such as underground gas and water pipes. These products are often made of blends of multiple types of PE with different molecular architectures. Although the long-term performance of these products is largely dictated by their local molecular structure, it has been studied mostly by indirect and bulk-averaging methods such as calorimetry and neutron scattering due to lack of chemical contrast for conventional imaging techniques. We demonstrate that broadband coherent anti-Stokes Raman scattering (CARS) microscopy can acquire images of the chemical composition and molecular orientation of a miscible semicrystalline PE blend with two different molecular architectures. We discuss the detailed crystal structure observed at different length scales and new insights it provides into polymer crystal morphology.
- 8 November 2012
- Published by American Chemical Society (ACS) in ACS Macro Letters
- Vol. 1 (11) , 1347-1351
Imaging the Molecular Structure of Polyethylene Blends with Broadband Coherent Raman Microscopy
Polyethylene (PE) has been widely used in a myriad of consumer products and critical infrastructure products such as underground gas and water pipes. These products are often made of blends of multiple types of PE with different molecular architectures. Although the long-term performance of these products is largely dictated by their local molecular structure, it has been studied mostly by indirect and bulk-averaging methods such as calorimetry and neutron scattering due to lack of chemical contrast for conventional imaging techniques. We demonstrate that broadband coherent anti-Stokes Raman scattering (CARS) microscopy can acquire images of the chemical composition and molecular orientation of a miscible semicrystalline PE blend with two different molecular architectures. We discuss the detailed crystal structure observed at different length scales and new insights it provides into polymer crystal morphology.
- 25 April 2012
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 45 (9) , 3866-3873
Solid Phase Synthesis of Polymacromer and Copolymacromer Brushes
- 25 April 2012
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 45 (9) , 3866-3873
Solid Phase Synthesis of Polymacromer and Copolymacromer Brushes
- 13 March 2009
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7272, 72722M
Nonplanar high-k dielectric thickness measurements using CD-SAXS
- 13 March 2009
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7272, 72722M
Nonplanar high-k dielectric thickness measurements using CD-SAXS
- 7 February 2004
- Published by American Chemical Society (ACS)
- p. 209-222
X-ray Reflectivity as a Metrology to Characterize Pores in Low-k Dielectric Films
- 7 February 2004
- Published by American Chemical Society (ACS)
- p. 209-222
X-ray Reflectivity as a Metrology to Characterize Pores in Low-k Dielectric Films
- 1 June 2003
- Published by Wiley in Polymer Engineering & Science
- Vol. 43 (6) , 1241-1249
Probe segregation and Tg determination of a supported ultra‐thin polystyrene film studied by X‐ray and neutron reflectivity, and SIMS
Selective deuteration combined with X‐ray and neutron reflectivity has been used to determine the extent of probe segregation to an interface in ultra‐thin polymer films as a function of the number of thermal cycles. The extent of probe segregation to the interface was also investigated using Secondary Ion Mass Spectroscopy (SIMS). Significant probe segregation was not evident in these studies. X‐ray reflectivity has also been employed to measure the coefficient of thermal expansion of ultra‐thin polystyrene films supported on quartz. The glass transition temperature determined with this method is equivalent to that measured for bulk polystyrene films.
- 1 June 2003
- Published by Wiley in Polymer Engineering & Science
- Vol. 43 (6) , 1241-1249
Probe segregation and Tg determination of a supported ultra‐thin polystyrene film studied by X‐ray and neutron reflectivity, and SIMS
Selective deuteration combined with X‐ray and neutron reflectivity has been used to determine the extent of probe segregation to an interface in ultra‐thin polymer films as a function of the number of thermal cycles. The extent of probe segregation to the interface was also investigated using Secondary Ion Mass Spectroscopy (SIMS). Significant probe segregation was not evident in these studies. X‐ray reflectivity has also been employed to measure the coefficient of thermal expansion of ultra‐thin polystyrene films supported on quartz. The glass transition temperature determined with this method is equivalent to that measured for bulk polystyrene films.
- 15 July 2002
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4690, 342-350
Chain conformation in ultrathin polymer films
Using Small Angle Neutron Scattering (SANS), we present the first quantitative measurements of the 3-dimensional conformation of macromolecules in thin polymer films of D < RG,Bulk, where D is the film thickness and RG,Bulk is the bulk radius of gyration. For D approximately equals 0.5 RG,Bulk, the molecular size along the film normal is less than 0.5 RG,Bulk, while relatively small changes are observed parallel to the surface. The observed changes in molecular size agree with predictions of molecular dynamics simulations of polymers confined in thin films, resulting from increased molecular orientation rather than chain distortion. Segregation of molecular centers of mass to the film center facilitates molecular packing while minimizing chain distortion. Estimates of length scales relating to the onset of chain distortion and chain orientation in thin film resists are D approximately equals 0.1 RG,Bulk and D approximately equals N(sigma ) respectively, where D is the film thickness, N is the number of chain segments, and (sigma) is the persistence length.
- 15 July 2002
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4690, 342-350
Chain conformation in ultrathin polymer films
Using Small Angle Neutron Scattering (SANS), we present the first quantitative measurements of the 3-dimensional conformation of macromolecules in thin polymer films of D < RG,Bulk, where D is the film thickness and RG,Bulk is the bulk radius of gyration. For D approximately equals 0.5 RG,Bulk, the molecular size along the film normal is less than 0.5 RG,Bulk, while relatively small changes are observed parallel to the surface. The observed changes in molecular size agree with predictions of molecular dynamics simulations of polymers confined in thin films, resulting from increased molecular orientation rather than chain distortion. Segregation of molecular centers of mass to the film center facilitates molecular packing while minimizing chain distortion. Estimates of length scales relating to the onset of chain distortion and chain orientation in thin film resists are D approximately equals 0.1 RG,Bulk and D approximately equals N(sigma ) respectively, where D is the film thickness, N is the number of chain segments, and (sigma) is the persistence length.
- 1 March 2002
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 20 (2) , 704-709
Combinatorial methodologies offer potential for rapid research of photoresist materials and formulations
A combinatorial research methodology is outlined with the potential to investigate material factors in photoresist formulations more rapidly than with traditional experimental design. The approach involves generating a gradient of processing variables in the photoresist film and using a set of analysis tools to “map” the photoresist properties as a function of the gradient variables. While high-throughput strategies have proven useful for empirical optimization of photoresist processing conditions, they have not been fully exploited to probe the complex array of material issues in projection lithography. Of primary importance in combinatorial methodologies is the generation of variable gradients. The focus of this article is to illustrate techniques to generate a gradient in bake temperature and bake time in the polymer films, and to illustrate that these gradient techniques can be used to probe fundamental properties of lithographic materials, such as deprotection kinetics. These gradient techniques were...
- 1 March 2002
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 20 (2) , 704-709
Combinatorial methodologies offer potential for rapid research of photoresist materials and formulations
A combinatorial research methodology is outlined with the potential to investigate material factors in photoresist formulations more rapidly than with traditional experimental design. The approach involves generating a gradient of processing variables in the photoresist film and using a set of analysis tools to “map” the photoresist properties as a function of the gradient variables. While high-throughput strategies have proven useful for empirical optimization of photoresist processing conditions, they have not been fully exploited to probe the complex array of material issues in projection lithography. Of primary importance in combinatorial methodologies is the generation of variable gradients. The focus of this article is to illustrate techniques to generate a gradient in bake temperature and bake time in the polymer films, and to illustrate that these gradient techniques can be used to probe fundamental properties of lithographic materials, such as deprotection kinetics. These gradient techniques were...
- 1 September 2001
- Published by Wiley in Polymer Engineering & Science
- Vol. 41 (9) , 1497-1505
Measuring Tg in ultra‐thin polymer films with an excimer fluorescence technique
An excimer fluorescence technique has been applied to the measurement of Tg of ultra‐thin polystyrene films. This technique utilizes an excimer‐forming molecule with fluorescent emission in two wavelength bands. The intensity ratio of these bands is a sensitive measure of local viscosity. This technique has been applied to five polystyrene films in the thickness range of 25 nm to 200 nm supported on quartz substrates. The observed Tg for the five ultra‐thin polymer films was similar to the bulk Tg with no observed dependence upon thickness. Additionally, the Tg determined for each film did not show any dependence upon thermal history.
- 1 September 2001
- Published by Wiley in Polymer Engineering & Science
- Vol. 41 (9) , 1497-1505
Measuring Tg in ultra‐thin polymer films with an excimer fluorescence technique
An excimer fluorescence technique has been applied to the measurement of Tg of ultra‐thin polystyrene films. This technique utilizes an excimer‐forming molecule with fluorescent emission in two wavelength bands. The intensity ratio of these bands is a sensitive measure of local viscosity. This technique has been applied to five polystyrene films in the thickness range of 25 nm to 200 nm supported on quartz substrates. The observed Tg for the five ultra‐thin polymer films was similar to the bulk Tg with no observed dependence upon thickness. Additionally, the Tg determined for each film did not show any dependence upon thermal history.
- 1 January 2001
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 148 (10) , F195-F199
X-Ray Reflectivity and FTIR Measurements of N[sub 2] Plasma Effects on the Density Profile of Hydrogen Silsesquioxane Thin Films
The density depth profile and chemical bond structure of hydrogen silsesquioxane (HSQ) thin films treated with an N2N2 plasma with varying power and exposure time were measured using specular X-ray reflectivity (SXR) and Fourier transform infrared (FTIR) spectroscopy. The SXR data indicated that the density profile of an untreated HSQ film is not uniform. At least four layers with different electron densities were required to fit the SXR data. For HSQ films treated with either increasing plasma power or plasma exposure time, the film roughness increased and a densified layer was observed at the film/air interface. The thickness of the densified layer increased with both plasma power and plasma exposure time. In the FTIR spectra of the plasma-treated films, the intensities of the Si-O peaks due to the network structure and the Si-OH peak due to water absorption increased and the intensities of the Si-H peaks decreased. The FTIR data show that the plasma converts the HSQ structure into a SiO2SiO2 -like structure and are consistent with the densification observed in the SXR measurements. In general, the HSQ film is more sensitive to increasing plasma power than to increasing plasma exposure time. © 2001 The Electrochemical Society. All rights reserved.
- 1 January 2001
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 148 (10) , F195-F199
X-Ray Reflectivity and FTIR Measurements of N[sub 2] Plasma Effects on the Density Profile of Hydrogen Silsesquioxane Thin Films
The density depth profile and chemical bond structure of hydrogen silsesquioxane (HSQ) thin films treated with an N2N2 plasma with varying power and exposure time were measured using specular X-ray reflectivity (SXR) and Fourier transform infrared (FTIR) spectroscopy. The SXR data indicated that the density profile of an untreated HSQ film is not uniform. At least four layers with different electron densities were required to fit the SXR data. For HSQ films treated with either increasing plasma power or plasma exposure time, the film roughness increased and a densified layer was observed at the film/air interface. The thickness of the densified layer increased with both plasma power and plasma exposure time. In the FTIR spectra of the plasma-treated films, the intensities of the Si-O peaks due to the network structure and the Si-OH peak due to water absorption increased and the intensities of the Si-H peaks decreased. The FTIR data show that the plasma converts the HSQ structure into a SiO2SiO2 -like structure and are consistent with the densification observed in the SXR measurements. In general, the HSQ film is more sensitive to increasing plasma power than to increasing plasma exposure time. © 2001 The Electrochemical Society. All rights reserved.