Mona Mostafa Hella
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mona Mostafa Hella has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Yu-Pin Hsu
Department of Electrical, Computer, and Systems Engineering, Rensselaer Polytechnic Institute, Troy, USA
2 shared publications - Zemin Liu
Department of Electrical, Computer, and Systems Engineering, Rensselaer Polytechnic Institute, Troy, USA
2 shared publications - Alexander Neumann
Center for High Technology Materials, University of New Mexico, Albuquerque, NM, USA
1 shared publication - Annick Penarier
Institut d’Électronique et des Systèmes, Université de Montpellier, Centre National de la Recherche Scientifique, 34095 Montpellier, France
1 shared publication - Asif Jahangir Chowdhury
Department of Electrical, Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY, USA
1 shared publication - Bassem Fahs
Department of Electrical, Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY, USA
1 shared publication
Latest Publications
- 1 January 2023
- Published by Optica Publishing Group
- p. W2A.5
Inverse-Designed Grating Arrays for High-Sensitivity Plenoptic Time-of-Flight Pixels
We present a plenoptic time-of-flight pixel design using grating arrays with inverse-designed passive photonic power combining to achieve scalable signal-to-noise ratio. Experimental results are presented as a proof-of-principle demonstration of the pixel architecture.
- 1 January 2023
- Published by Optica Publishing Group
- p. W2A.5
Inverse-Designed Grating Arrays for High-Sensitivity Plenoptic Time-of-Flight Pixels
We present a plenoptic time-of-flight pixel design using grating arrays with inverse-designed passive photonic power combining to achieve scalable signal-to-noise ratio. Experimental results are presented as a proof-of-principle demonstration of the pixel architecture.
- Open Access
- 1 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 22 (5) , 42-59
2021 Microwave Week Workshops
Presents information on 2021 Microwave Week Workshops.
- 1 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 22 (5) , 42-59
Open Access2021 Microwave Week Workshops
Presents information on 2021 Microwave Week Workshops.
- 1 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 476-479
A 99 - 132 GHz Frequency Quadrupler with 8.5 dBm Peak Output Power and 8.8% DC-to-RF Efficiency in 130 nm BiCMOS
This paper presents the design of a frequency quadrupler which operates at 116 GHz in 130 nm BiCMOS process. The quadrupler consists of two-stage cascaded frequency doublers with two wideband baluns. The measured peak output power is 8.5 dBm at 116 GHz, and the 3-dB bandwidth is from 99 GHz to 132 GHz. The frequency quadrupler consumes 24 mA DC current from a 3.3 V power supply. The peak DC-to-RF efficiency of the quadrupler is 8.8%. To the best of the authors knowledge, this is the highest reported output power and efficiency achieved by frequency multiplier without a dedicated power amplifier in this frequency range with silicon processes.
- 1 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 476-479
A 99 - 132 GHz Frequency Quadrupler with 8.5 dBm Peak Output Power and 8.8% DC-to-RF Efficiency in 130 nm BiCMOS
This paper presents the design of a frequency quadrupler which operates at 116 GHz in 130 nm BiCMOS process. The quadrupler consists of two-stage cascaded frequency doublers with two wideband baluns. The measured peak output power is 8.5 dBm at 116 GHz, and the 3-dB bandwidth is from 99 GHz to 132 GHz. The frequency quadrupler consumes 24 mA DC current from a 3.3 V power supply. The peak DC-to-RF efficiency of the quadrupler is 8.8%. To the best of the authors knowledge, this is the highest reported output power and efficiency achieved by frequency multiplier without a dedicated power amplifier in this frequency range with silicon processes.
- 27 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (12) , 1859-1863
A 1.8 $\mu$ W −65 dB THD ECG Acquisition Front-End IC Using a Bandpass Instrumentation Amplifier With Class-AB Output ConfigurationThis brief presents a power-efficient, highly linear front-end (FE) integrated circuit (IC) for electrocardiogram (ECG) acquisition applications. Compared to typical FE architectures, the proposed FE uses only one bandpass instrumentation amplifier (IA) to reduce the chip area and dc power consumption. To achieve high linearity, the bandpass IA is composed of a high-gain two-stage amplifier in a capacitive-feedback configuration. Miller compensation and the class-AB output stage are utilized to incorporate the filtering and buffering functions within the IA without the need for additional circuit stages. The FE IC is fabricated in 0.13-μm CMOS technology, and occupies only a 0.16-mm 2 chip area. The measured input-referred noise is 3.2 μVrms with a midband gain of 34.6 dB, and a bandwidth that extends from 0.9 to 350 Hz. A total harmonic distortion of -65 dB is measured at an input signal of 5.5 mV pp , with a dc power consumption of 1.8 μW. In a real-time measurement, the proposed FE IC is capable of detecting high-fidelity ECG waveforms.
- 27 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (12) , 1859-1863
A 1.8 $\mu$ W −65 dB THD ECG Acquisition Front-End IC Using a Bandpass Instrumentation Amplifier With Class-AB Output ConfigurationThis brief presents a power-efficient, highly linear front-end (FE) integrated circuit (IC) for electrocardiogram (ECG) acquisition applications. Compared to typical FE architectures, the proposed FE uses only one bandpass instrumentation amplifier (IA) to reduce the chip area and dc power consumption. To achieve high linearity, the bandpass IA is composed of a high-gain two-stage amplifier in a capacitive-feedback configuration. Miller compensation and the class-AB output stage are utilized to incorporate the filtering and buffering functions within the IA without the need for additional circuit stages. The FE IC is fabricated in 0.13-μm CMOS technology, and occupies only a 0.16-mm 2 chip area. The measured input-referred noise is 3.2 μVrms with a midband gain of 34.6 dB, and a bandwidth that extends from 0.9 to 350 Hz. A total harmonic distortion of -65 dB is measured at an input signal of 5.5 mV pp , with a dc power consumption of 1.8 μW. In a real-time measurement, the proposed FE IC is capable of detecting high-fidelity ECG waveforms.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Characterization and optimization of a blue-enhanced honeycomb optical sensor
A honeycomb photodetector architecture is proposed for low-cost CMOS-compatible blue-enhanced sensing applications. In this paper, a physical model is developed to characterize the responsivity of honeycomb photodetectors. The model is then used to determine the optimum honeycomb physical dimensions for maximum responsivity and quantum efficiency. To implement the model in a real application, a test chip with honeycomb structures is designed, fabricated, and characterized using a commercial 0.35 pm standard CMOS process through Austria Micro Systems (AMS). Based on measured data, the optimal honeycomb structure in this fabrication process improves the quantum efficiency by 63% at 375 nm wavelength.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Characterization and optimization of a blue-enhanced honeycomb optical sensor
A honeycomb photodetector architecture is proposed for low-cost CMOS-compatible blue-enhanced sensing applications. In this paper, a physical model is developed to characterize the responsivity of honeycomb photodetectors. The model is then used to determine the optimum honeycomb physical dimensions for maximum responsivity and quantum efficiency. To implement the model in a real application, a test chip with honeycomb structures is designed, fabricated, and characterized using a commercial 0.35 pm standard CMOS process through Austria Micro Systems (AMS). Based on measured data, the optimal honeycomb structure in this fabrication process improves the quantum efficiency by 63% at 375 nm wavelength.
- 11 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1538-1541
A low-power adjustable bandwidth biomedical signals acquisition SoC for continuous health monitoring system
A low-power biomedical signal acquisition SoC is proposed for continuous health monitoring system. The SoC fully integrates a low-noise analog front-end (AFE), a current-steering low-pass filter (CSLPF), and an output buffer. A DC-rejection loop and a chopping function are added to enhance the noise performance. For processing various bio-signals, the bandwidth can be adjusted to extract the signals in specific bands. The SoC, designed in a standard 0.13μm CMOS technology, passes signals from 0.3Hz to 154Hz and from 0.5Hz to 117Hz with a simulated input referred noise of 0.4μVrms and achieves maximum gains of 36dB and 42dB respectively. The power consumption is 1μW from a 1V DC supply voltage.
- 11 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1538-1541
A low-power adjustable bandwidth biomedical signals acquisition SoC for continuous health monitoring system
A low-power biomedical signal acquisition SoC is proposed for continuous health monitoring system. The SoC fully integrates a low-noise analog front-end (AFE), a current-steering low-pass filter (CSLPF), and an output buffer. A DC-rejection loop and a chopping function are added to enhance the noise performance. For processing various bio-signals, the bandwidth can be adjusted to extract the signals in specific bands. The SoC, designed in a standard 0.13μm CMOS technology, passes signals from 0.3Hz to 154Hz and from 0.5Hz to 117Hz with a simulated input referred noise of 0.4μVrms and achieves maximum gains of 36dB and 42dB respectively. The power consumption is 1μW from a 1V DC supply voltage.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 0149645X,p. 1-4
Characterization of integrated antenna-coupled plasma-wave detectors with wide bandwidth amplification in 130nm CMOS
A fully integrated 0.3 THz antenna-coupled plasma-wave detector with 10 GHz (measured) bandwidth is presented. Fabricated in 130nm CMOS technology, the chip is formed of an E-shaped patch antenna, plasmonic based Field Effect Transistor (FET) detector and a wide bandwidth amplifier employing inductive shunt peaking. The open drain mode of operation of the detector achieves an absolute responsivity of 10 V/W with a minimum signal to noise ratio (SNR) of 40 dB over the entire bandwidth. With a drain current of 0.24 mA, the responsivity increases by 10X with a decrease in bandwidth to 3 GHz. The detector is also characterized without the on chip amplifier for imaging applications and shows a measured absolute responsivity of 150 V/W for a drain current of 5 μA at 0.3 THz.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 0149645X,p. 1-4
Characterization of integrated antenna-coupled plasma-wave detectors with wide bandwidth amplification in 130nm CMOS
A fully integrated 0.3 THz antenna-coupled plasma-wave detector with 10 GHz (measured) bandwidth is presented. Fabricated in 130nm CMOS technology, the chip is formed of an E-shaped patch antenna, plasmonic based Field Effect Transistor (FET) detector and a wide bandwidth amplifier employing inductive shunt peaking. The open drain mode of operation of the detector achieves an absolute responsivity of 10 V/W with a minimum signal to noise ratio (SNR) of 40 dB over the entire bandwidth. With a drain current of 0.24 mA, the responsivity increases by 10X with a decrease in bandwidth to 3 GHz. The detector is also characterized without the on chip amplifier for imaging applications and shows a measured absolute responsivity of 150 V/W for a drain current of 5 μA at 0.3 THz.