Udayagiri Chandrasekhar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Udayagiri Chandrasekhar has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Balasubramanian Esakki
National Institute of Technical Teachers Training and Research
3 shared publications - Sachin Salunkhe
Department of Biosciences, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences, Chennai, India
2 shared publications A Vivek
Instrumentation and Control Engineering Department, National Institute of Technology, Tiruchirappalli, Tamil Nadu, India
1 shared publicationAnv Rao
Gas Turbine Research Establishment, Bangalore, Karnataka, India
1 shared publicationChandrakumar Palanisamy
Department of Mechanical Engineering, VelTech University, Chennai, India
1 shared publication- Devaraj Rajamani
Centre for Autonomous System Research, Department of Mechanical Engineering, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Chennai 600062, India
1 shared publication
Latest Publications
- 27 September 2020
- Published by Springer Nature
- p. 171-179
Numerical Modeling and Analysis of a Multi-rotor UAS
- 27 September 2020
- Published by Springer Nature
- p. 171-179
Numerical Modeling and Analysis of a Multi-rotor UAS
- 12 August 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 234 (2) , 342-360
Novel resistor-capacitor (RC) network-based capacitance signal conditioning circuit for tip clearance measurement on gas turbine engine
Blade tip clearance is a critical engine health parameter measured on gas turbines. Increase in tip clearance results in decreased efficiency, whereas with decrease in clearance due to thermal and centrifugal loads, rotor blades might rub the engine case. Various sensing techniques are being used, among them, capacitance-based systems are widely used by many engine houses. Among the capacitance conditioning circuits, resistor-capacitor series network-based circuits are simple to implement but pose many challenges during practical development. During the current work, the authors have designed a novel capacitance conditioning circuit combining resistor-capacitor series network, instrumentation amplifiers, and direct current–direct current converters. Performance of the developed capacitance conditioning electronics was evaluated through lab testing and tip clearance measurement on fan stage of an aero gas turbine engine. The prototype conditioner circuit has efficiently conditioned and resolved small capacitances varying from 1.25 pF to 0.00413 pF for running clearances between 0.4 mm and 3 mm, respectively. The developed electronics produced high output with signal-to-noise ratio of 58.1 dB, resolution of 2.5 µm, bandwidth of about 700 kHz, and an accuracy of about 98%. This development has culminated towards miniaturization of the total electronics and has the potential to get developed as smart capacitance sensor. This paper explains the practical aspects and challenges involved while designing and developing such practical conditioning circuits.
- 12 August 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 234 (2) , 342-360
Novel resistor-capacitor (RC) network-based capacitance signal conditioning circuit for tip clearance measurement on gas turbine engine
Blade tip clearance is a critical engine health parameter measured on gas turbines. Increase in tip clearance results in decreased efficiency, whereas with decrease in clearance due to thermal and centrifugal loads, rotor blades might rub the engine case. Various sensing techniques are being used, among them, capacitance-based systems are widely used by many engine houses. Among the capacitance conditioning circuits, resistor-capacitor series network-based circuits are simple to implement but pose many challenges during practical development. During the current work, the authors have designed a novel capacitance conditioning circuit combining resistor-capacitor series network, instrumentation amplifiers, and direct current–direct current converters. Performance of the developed capacitance conditioning electronics was evaluated through lab testing and tip clearance measurement on fan stage of an aero gas turbine engine. The prototype conditioner circuit has efficiently conditioned and resolved small capacitances varying from 1.25 pF to 0.00413 pF for running clearances between 0.4 mm and 3 mm, respectively. The developed electronics produced high output with signal-to-noise ratio of 58.1 dB, resolution of 2.5 µm, bandwidth of about 700 kHz, and an accuracy of about 98%. This development has culminated towards miniaturization of the total electronics and has the potential to get developed as smart capacitance sensor. This paper explains the practical aspects and challenges involved while designing and developing such practical conditioning circuits.
- Open Access
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Materials Engineering Innovation
- Vol. 10 (1) , 20
Prediction of life of piercing punches using artificial neural network and adaptive neuro fuzzy inference systems
International publishers of academic, scientific and professional journals since 1979.
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Materials Engineering Innovation
- Vol. 10 (1) , 20
Open AccessPrediction of life of piercing punches using artificial neural network and adaptive neuro fuzzy inference systems
International publishers of academic, scientific and professional journals since 1979.
- 13 June 2017
- Published by Taylor & Francis in Composite Interfaces
- Vol. 25 (2) , 151-168
Enhancing the interfacial strength of glass/epoxy composites using ZnO nanowires
- 13 June 2017
- Published by Taylor & Francis in Composite Interfaces
- Vol. 25 (2) , 151-168
Enhancing the interfacial strength of glass/epoxy composites using ZnO nanowires