Hsin-Shu Peng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hsin-Shu Peng has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Po-Wei Huang
Mechanical and Automation Engineering, College of Engineering, Taiwan Steel University of Science and Technology, Kaohsiung 821013, Taiwan
2 shared publications Hung-Wei Chen
Mechanical and Computer-Aided Engineering, College of Engineering, Feng Chia University , Taichung , Taiwan
1 shared publicationKai-Fu Liew
Feng Chia University,Department of Ph. D. Program of Mechanical and Aeronautical Engineering,Taichung City,Taiwan, R.O.C.
1 shared publication- Wei-Huang Choong
Ph.D. Program of Mechanical and Aeronautical Engineering, Feng Chia University College of Engineering and Science, Taichung 40724, Taiwan
1 shared publication - Weijie J. Su
University of Pennsylvania, Philadelphia, USA
1 shared publication
Latest Publications
- 26 December 2025
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 46 (2) , 182-193
Heating-mechanism of gas, short-shot method, and their experimental and benefit analysis on hollow structure of gas-assisted injection-molded specimens
Gas-assisted injection molding (GAIM) introduces high-pressure gas into the mold cavity after molten plastic injection, creating a hollow structure that reduces material usage and improves warpage and cooling deformation, particularly in thick-walled parts. However, conventional GAIM typically employs nitrogen at around 15 °C, which often leads to condensation and pressure drops due to the temperature difference with the molten polymer. These issues result in unstable gas penetration, asymmetric hollow structures, reduced dimensional stability, and surface defects from insufficient gas support. To address these challenges, this study integrates a gas heating module into the GAIM process and systematically evaluates its effects using the short-shot method and spiral-flow specimens. Experimental results show that gas preheating reduces solid material usage by more than 6 % and achieves an average weight reduction above 20 %, attributed to slower cooling and enhanced hollow formation. Heated gas also decreases shrinkage variability by over 20 %, lowers the overall shrinkage rate by ∼5 %, and simultaneously reduces melt pressure by ∼10 % while stabilizing gas output by ∼15 %, thereby improving dimensional stability and process robustness. Furthermore, the hollow ratio is increased by 15–20 % and penetration length is extended by ∼20 %, resulting in more continuous, symmetric, and well-defined hollow structures.
- 26 December 2025
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 46 (2) , 182-193
Heating-mechanism of gas, short-shot method, and their experimental and benefit analysis on hollow structure of gas-assisted injection-molded specimens
Gas-assisted injection molding (GAIM) introduces high-pressure gas into the mold cavity after molten plastic injection, creating a hollow structure that reduces material usage and improves warpage and cooling deformation, particularly in thick-walled parts. However, conventional GAIM typically employs nitrogen at around 15 °C, which often leads to condensation and pressure drops due to the temperature difference with the molten polymer. These issues result in unstable gas penetration, asymmetric hollow structures, reduced dimensional stability, and surface defects from insufficient gas support. To address these challenges, this study integrates a gas heating module into the GAIM process and systematically evaluates its effects using the short-shot method and spiral-flow specimens. Experimental results show that gas preheating reduces solid material usage by more than 6 % and achieves an average weight reduction above 20 %, attributed to slower cooling and enhanced hollow formation. Heated gas also decreases shrinkage variability by over 20 %, lowers the overall shrinkage rate by ∼5 %, and simultaneously reduces melt pressure by ∼10 % while stabilizing gas output by ∼15 %, thereby improving dimensional stability and process robustness. Furthermore, the hollow ratio is increased by 15–20 % and penetration length is extended by ∼20 %, resulting in more continuous, symmetric, and well-defined hollow structures.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 24-27
Investigations of the Effects of Cavity-Surface Temperature and Fiber Compatible on Weldline Tensile Strength of Long Glass Fiber Reinforced PA66 Injection Molded Parts
This study used the cavity-surface infrared rapid-heating method and tensile specimens (ASTM-D638) to test the fiber compatibility and tensile characteristics of long glass fiber reinforced PA66 (LGF-PA66) composites. The weldline molding experiment on the injected specimen was conducted using a double-gate. In addition, the integration of infrared heating and cavity pressure measurement were developed to achieve cavity-surface heating and observe the effect of with/without cavity-surf ace heating on weldline tensile strength variation and correlated pressure distribution near the weldline region. On the other hand, a vent -well was designed in the center position of the specimen (vent-well depths are 0.9 mm, 1.8 mm, and 3.6 mm), in order to discuss the effect of the two-melts on fiber and melt compatibility in the compatible process. The experimental results show that vent-well provides better weldline tensile strength; moreover, infrared heating cavity -surface also provides the better weldline tensile strength of LGF-PA66 composites molded parts. In addition, from SEM images and cavity pressure distributions, considering in presence or absence of vent-well design and cavity-surface heating, it provides better weldline tensile strength and interfaces compatibility between fiber and resin at weldline region during molding stage.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 24-27
Investigations of the Effects of Cavity-Surface Temperature and Fiber Compatible on Weldline Tensile Strength of Long Glass Fiber Reinforced PA66 Injection Molded Parts
This study used the cavity-surface infrared rapid-heating method and tensile specimens (ASTM-D638) to test the fiber compatibility and tensile characteristics of long glass fiber reinforced PA66 (LGF-PA66) composites. The weldline molding experiment on the injected specimen was conducted using a double-gate. In addition, the integration of infrared heating and cavity pressure measurement were developed to achieve cavity-surface heating and observe the effect of with/without cavity-surf ace heating on weldline tensile strength variation and correlated pressure distribution near the weldline region. On the other hand, a vent -well was designed in the center position of the specimen (vent-well depths are 0.9 mm, 1.8 mm, and 3.6 mm), in order to discuss the effect of the two-melts on fiber and melt compatibility in the compatible process. The experimental results show that vent-well provides better weldline tensile strength; moreover, infrared heating cavity -surface also provides the better weldline tensile strength of LGF-PA66 composites molded parts. In addition, from SEM images and cavity pressure distributions, considering in presence or absence of vent-well design and cavity-surface heating, it provides better weldline tensile strength and interfaces compatibility between fiber and resin at weldline region during molding stage.