SASufizar Ahmad

Sufizar Ahmad

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sufizar Ahmad has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • XRD and EDS Analysis of Composite Cathode Powders LSCF-SDCC-Ag for Low Temperature Solid Oxide Fuel Cells (LTSOFC)

    by M.S.A. Bakar, Sufizar Ahmad, Hamimah Abdul Rahman, H. Basri, A. Muchtar

    X-ray diffraction (XRD) and energy dispersion spectroscopy (EDS) analysis has been conducted on composite cathode powder LSCF-SDCC-Ag. Composite cathode powder LSCF-SDCC has been produced using high energy ball milling via wet milling method through calcinations at 750 °C. The calcined LSCF-SDCC powder then was mixed with Ag (3wt%) then pressed become pellets and sintered at 500, 550 and 600 °C. The phase purity of composite cathode powder LSCF-SDCC-Ag was determined via XRD analysis and elements distributions were observed via EDS-mapping. The SrCO3 phase was emerged after the addition of composite cathode powder LSCF-SDCC with Ag powder. The phase purity of composite cathode powder LSCF-SDCC-Ag were maintained before and after sintered. The variable of sintering temperature also not effect the structure as there were no other secondary constituent emerged as confirmed by XRD sensitivity. EDS analysis shows LSCF-SDCC-Ag produced via ball milling has uniform distribution of elements.


  • Brief Review: Electrochemical Performance of LSCF Composite Cathodes - Influence of Ceria-Electrolyte and Metals Element

    by Sufizar Ahmad, M.S.A. Bakar, Hamimah Abdul Rahman, A. Muchtar

    Solid oxide fuel cells (SOFC) are an efficient and clean power generation devices. Low-temperature SOFC (LTSOFC) has been developed since high-temperature SOFC (HTSOFC) are not feasible to be commercialized because high in cost. Lowering the operation temperature has caused substantial performance decline resulting from cathode polarization resistance and overpotential of cathode. The development of composite cathodes regarding mixed ionic-electronic conductor (MIEC) and ceria based materials for LTSOFC significantly minimize the problems and leading to the increasing in electrocatalytic activity for the oxygen reduction reaction (ORR) to occur. Lanthanum-based materials such as lanthanum strontium cobalt ferrite (La0.6Sr0.4Co0.2Fe0.8O3-δ) recently have been discovered to offer great compatibility with ceria-based electrolytes to be applied as composite cathode materials for LTSOFC. Cell performance at lower operating temperature can be maintained and further improved by enhancing the ORR. This paper reviews recent development of various ceria-based composite cathodes especially related to the ceria-carbonate composite electrolytes for LTSOFC. The influence of the addition of metallic elements such as silver (Ag), platinum (Pt) and palladium (Pd) towards the electrochemical properties and performance of LSCF composite cathodes are briefly discussed.


  • Potassium Bromide as Space Holder for Titanium Foam Preparation

    by Fazimah Mat Noor, M.I.M. Zain, K.R. Jamaludin, R. Hussin, Z. Kamdi, A. Ismail, Sufizar Ahmad, H. Taib

    Titanium (Ti) alloy foam was prepared by using potassium bromide (KBr) as space holder with percentage between 20 to 40 wt.%. In this work, the potential of KBr as a new space holder was determined. The Ti alloy powder and space holder were first manually mixed before being compacted using hydraulic hand press. The green compacts were then sintered at temperature of 1160°C, 1200°C and 1240°C in a tube furnace. The microstructure of the Ti alloy foams were observed by Scanning Electron Microscope (SEM). It was revealed that the porosity content in the Ti foam was in the range of 16% to 31% and density in the range of 1.5 g/cm3 to 2.6 g/cm3. Moreover, the pore size of the titanium alloy foam is in the range of 187μm to 303μm. Although the sintering temperatures were found incapable of promoting overall densification to the Ti alloy foam, 1200°C was denoted to be the maximal temperature for promoting maximal porosity to the Ti alloy foam. Nonetheless, KBr was proven to be suitable as space holder for Ti foam preparation as referred to its stability and insolubility in the Ti alloy.


  • Parameter Optimization towards Highest Micro MIM Density by Using Taguchi Method

    by Mohd Halim Irwan Ibrahim, Norhamidi Muhamad, Abu Bakar Sulong, Khairur Rijal Jamaludin, Nor Hafiez Mohamad Nor, Sufizar Ahmad, Mohd Ruzi Harun, Hafizawati Zakaria

    Nowadays, micro metal injection molding has become among the promising method in powder metallurgy research to produce small-scale intricate part at an effective process and competitive cost for mass production. This paper investigated the optimization of highest green strength which plays an important characteristic in determining the successful of micro MIM. In this paper, stainless steel SS 316L with D50 = 5.96µm was used with composite binder, which consists of PEG (Polyethelena Glycol), PMMA (Polymethyl Methacrilate) and SA (Stearic Acid). Feedstock with 61.5% with several injection parameters were optimized which highly significant through screening experiment such as injection pressure(A), injection temperature(B), mold temperature(C), injection time(D) and holding time(E). Besides that, interaction effects between injection pressure, injection temperature and mold temperature were also considered to optimize in the Taguchi’s orthogonal array. Analysis of variance (ANOVA) in terms of signal-to-noise ratio (S/N-larger is better) for green density was also presented in this paper. Result shows that interaction between injection temperature and mold temperature(BxC) give highest significant factor followed by interaction between injection pressure and mold temperature(AxC). Single factor that also contributes to significant optimization are mold temperature(C) and injection time(D). This study shows that Taguchi method would be among the best method to solve the problem with minimum number of trials.