MZMing Zhao

Ming Zhao

*This is an algorithmically generated author record based on publicly available information.

Ming Zhao has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study on hydraulic losses in fixed flow passage components of a Pelton turbine under sedimentladen flow

    by Gang Yu, Gang Yu, Tingyi Shen, Ming Zhao, Yuyang Guo, Ning Ning Song

    Pelton turbines are increasingly widely applied in hydropower development in highhead, sedimentladen rivers in Southwest China. However, the hydraulic loss mechanisms in their fixed flow passage components (distributor and injector) under sedimentladen flow conditions remain unclear, and traditional methods are inadequate to precisely locate loss sources and quantify sediment impacts. To address this issue, this paper takes a sixnozzle Pelton turbine with four deflectors as the research object, establishes a gasliquidsolid threephase numerical simulation method based on the VOF multiphase model, the SST kω turbulence model, and the DPM discrete phase model, and introduces the entropy production theory to quantitatively evaluate and spatially resolve the energy losses in the distributor and injector under both clearwater and sedimentladen conditions.The results indicate that sediment-laden flow increases the indirect entropy production in the entire flow passage by approximately 20% compared with clear-water conditions, with the increments concentrated at the trailing edge of the deflectors, the needle tail, and the distributor bifurcations. The inertial perturbation of sediment particles expands the region of direct entropy production and exacerbates turbulent dissipation through particlevortex coupling, leading to a significant deterioration of jet stability at the nozzle outlet. The inlet flow fields of different nozzles exhibit notable differences due to the transport of secondary flow from the distributor. Although the deflectors can effectively rectify the flow, the Kármán vortex street at their trailing edge induces additional losses. Moreover, extending the trailingedge length of the deflector (560 mm scheme) can smooth the adverse pressure gradient, delay boundary layer separation, and effectively reduce the energy dissipation in the shear layer. This study quantitatively reveals the enhancement mechanism of sediment on hydraulic losses in fixed flow passage components and the regulating effect of deflector geometry, providing a theoretical basis for efficiency improvement and antierosion optimization design of Pelton turbines in high sedimentladen regions.

  • Open Access

    POD-Based modal decomposition and reduced-order modeling for full-range unsteady flow in a residual pressure recovery turbine

    by Jia-Xing Lu, Tao Yang, Yuyang Guo, Hongjian Wang, Ming Zhao, Shaoxian Chen, Jian Huang

    To characterize the unsteady flow behavior of a residual pressure recovery hydraulic turbine across its entire operating range, the transient pressure and velocity fields at three typical flow rates—0.7 Qd, Qd, and 1.3 Qd—were modally decomposed using proper orthogonal decomposition (POD). Combined with turbulent kinetic energy (TKE) contours and the Q-criterion vortex identification method, the topological evolution of the flow field and the energy distribution characteristics of the dominant modes were systematically revealed under different flow conditions. The results show that the variation of the inflow incidence angle is the critical factor driving the fundamental change in the flow field structure. Under the rated condition, a zero incidence angle ensured smooth flow attachment; the blade passing frequency (BPF) induced by rotor–stator interaction (RSI) became the sole dominant source of flow fluctuations. The flow field exhibited strong low-dimensional characteristics: the first four pressure and velocity modes captured more than 95% of the total modal energy, and retaining only four modes was sufficient to keep the relative reconstruction error below 10⁻³. Under the low-flow condition, the positive incidence angle induced flow separation on the suction surface and generated discrete blade passage vortices, causing the flow energy to be widely dispersed; at least 12 modes had to be retained to achieve the same reconstruction accuracy. Under the high-flow condition, the negative incidence angle led to large-scale separation on the pressure surface, and a large-scale central helical instability structure appeared in the flow passage. The flow field exhibited mixed convergence characteristics of BPF periodicity and helical instability, and retaining eight modes effectively balanced computational accuracy and efficiency. In this study, the optimal modal truncation orders of the POD-based reduced-order model across the entire operating range were quantitatively and precisely determined. These findings provide an essential theoretical basis and data support for rapid flow field reconstruction, hydraulic excitation suppression, and blade profile optimization of residual pressure recovery hydraulic turbines under off-design conditions.

  • Open Access

    Effect of runner blade number on off-design hydraulic performance and flow stability of a residual pressure recovery turbine

    by Jia-Xing Lu, Ming Zhao, Hui Li, Yuyang Guo, Gang Yu, Ningning Song, Tao Wang

    To mitigate the substantial dissipation of pressure energy by pressure reducing valves (PRVs) in urban water distribution networks, this study examines a pipe-type residual-pressure recovery turbine. By integrating computational fluid dynamics (CFD) with entropy production analysis, a systematic comparative investigation was performed on runners with blade counts of 13, 14, and 15 under off-design operating conditions (Q = 0.7Qd), elucidating the hydraulic performance, internal vortical flow structures, pressure fluctuation characteristics, and energy loss mechanisms.,The results demonstrate that an increased blade number effectively restrains suction-side flow separation and passage vortices triggered by incidence angle mismatch under reduced-flow conditions, consequently attenuating turbulence dissipation losses. Nevertheless, an excessive blade count (Z = 15) intensifies leading-edge impingement losses and rotor–stator interaction. The 14-blade runner strikes an optimal balance between suppressing separation vortices and controlling additional losses, achieving an off-design efficiency of 79.78%—markedly surpassing that of the 13-blade configuration (76.87%) while remaining comparable to the 15-blade scheme (79.94%).Furthermore, the 14-blade runner exhibits the minimum average vortex volume and pressure fluctuation amplitudes among the three candidates, with pronounced attenuation of both low-frequency broadband perturbations and blade-passing-frequency dominant peaks. Entropy production analysis further corroborates that the 14-blade configuration yields a more uniform entropy generation distribution and substantially diminished irreversible losses within the runner domain.,Collectively, these findings establish the 14-blade configuration as the preferred design that concurrently accommodates wide-load hydraulic efficiency, hydrodynamic stability, and engineering economy, thereby furnishing theoretical foundations for blade-number optimization of residual-pressure recovery turbines in water supply networks.

  • Open Access

    Identification of Safe-Aeration Concentration and Energy Dissipation Characteristic in Pumping Mode of a Pump-Turbine

    by Jia-Xing Lu, Ming Zhao, Yuyang Guo, Hui Li, Chuan Zhang, Baoshan Zhu

    In pumped storage systems, the pump-turbine serves as the core energy conversion component, and its operating efficiency directly influences the overall performance and energy loss of the storage system. Cavitation is a key factor leading to efficiency degradation and structural damage, while aeration, as an active control method, can suppress cavitation but may also introduce additional flow instability and energy loss. Currently, how to maximize energy conversion efficiency and minimize losses during the aeration process remains a critical scientific issue to be addressed in energy storage technology.This study integrates full-flow-field visualization experiments with coupled CFD-PBM-entropy production numerical simulations to systematically reveal the influence mechanism of aeration concentration on the energy conversion process in pump-turbines under pump mode. By establishing an Eulerian–Eulerian two-fluid model coupled with a population balance model and incorporating entropy production theory, the spatial distribution of energy dissipation under different aeration conditions is quantified from a thermodynamic perspective. The research finds that there exists a safe aeration concentration window (α = 0.005-0.03), within which aeration can effectively suppress vibration while maintaining stable hydraulic efficiency and relatively low energy loss. Once the critical threshold (α ≈ 0.045) is exceeded, intensified bubble accumulation and breakup in the runner inter-blade passages trigger vortex structure complexity and localized concentration of turbulent kinetic energy, leading to a significant increase in entropy production rate, a sharp drop in efficiency, and a peak in additional loss power. For the first time, this study clarifies the dual-impact mechanism of aeration on energy conversion and performance in pump-turbines from the perspective of energy dissipation, providing a theoretical basis and quantitative operational guidance for aeration optimization and efficient energy management in pumped-storage power stations. The relevant findings hold significant engineering importance for enhancing the operational stability of energy storage systems and reducing energy loss.

  • Open Access

    Influence of Bézier Curve based variable-speed control strategies on transient flow characteristics in pump-turbine under pump mode: A combined vortex dynamics and rothalpy analysis

    by Jia-Xing Lu, Yuyang Guo, Hui Li, Ming Zhao, Yilong Qiu

    This study systematically explores how Bézier curve-based variable-speed control strategies affect the internal flow characteristics of a pump-turbine (PT) in pump mode, via integrating the Omega vortex identification method, rothalpy change theory, and Frequency Slice Wavelet Transform (FSWT)-based time-frequency analysis. A combined approach of full-flow-passage visualization experiments and high-fidelity Computational Fluid Dynamics (CFD) simulations is adopted to clarify vortex evolution and its correlation with pressure pulsations during transient speed changes. Results show that the quadratic Bézier strategy outperforms the linear one: externally, it enables smoother power transition, cutting power oscillation amplitude by ~16.3% and thus mitigating hydraulic impact; internally, it renders vortex structures in double-row cascades and runners more orderly, with a 51.57% reduction in steady-state vortex intensity, suppresses small-scale turbulence and flow separation, and homogenizes rothalpy gradients to curb disordered vortices. Pressure pulsation analysis confirms reduced amplitudes and stable time-domain traits across mid-span sections; time-frequency analysis further reveals concentrated pulsation energy and suppressed high-frequency components under quadratic regulation. This work deepens insights into internal flow control of variable-speed PTs and provides theoretical and strategic support for the optimal design and stable, efficient operation of such units.

  • Energy loss characteristics of gas–liquid two-phase flow in pump-turbines under pumping mode

    by Jiaxing Lu, Chuan Zhang, Ming Zhao, Yuyang Guo, Xiaobing Liu, Baoshan Zhu, Liang Jiang

    In gas–liquid two-phase flow within the pump mode of a pump-turbine, a trade-off was observed between the cavitation control and intensified energy dissipation due to gas-phase introduction. This study integrated experimental research with a Computational Fluid Dynamics-Population Balance Model (CFD-PBM) coupled model to investigate the influence mechanisms of air-injection concentration and flow conditions on energy loss. The reliability of the CFD-PBM numerical method for simulating gas–liquid two-phase flow in the pump mode of a pump-turbine was validated. Air-injection concentration was found to redistribute energy losses across flow passages. The primary energy dissipation zone, influenced by gas-phase accumulation, migrated from the double-row guide vanes to the runner passage as the air-injection concentration increased. Furthermore, due to gas-phase aggregation in low-pressure regions, energy dissipation on the low-pressure surface remained consistently higher than that on the high-pressure surface. Under constant air-injection conditions, flow rate magnitude affected entropy production migration. The runner passage persisted as the dominant energy dissipation zone across all flow rates, while the secondary dissipation zone shifted from the guide vane passage to the stay guide vane passage as the flow rate increased. Localized high entropy production regions induced by gas-phase accumulation in the runner blade channels were governed by bubble size, pressure gradient, liquid-phase backflow, and interphase interactions.