SSSoya Sato

Soya Sato

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Soya Sato has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dual-axis acoustically driven MEMS mirror enhanced by parallel double-layer Helmholtz resonator array

    by Masahiro Fukuta, Soya Sato, Hidetoshi Takahashi

    This study presents a dual-axis acoustically actuated microelectromechanical system (MEMS) mirror enhanced by a parallel double-layer Helmholtz resonator (HR) array. Acoustic actuation is attractive for MEMS mirrors owing to its structural simplicity and external driving capability; however, the limited energy of sound waves complicates the achievement of large-amplitude and multi-axis actuation. Our proposed device integrates a laser-fabricated glass cantilever mirror with a three-dimensional-printed HR array designed to generate two distinct acoustic-resonance peaks. By tuning these peaks to match the mechanical resonant frequencies of the mirror, the acoustic pressure at each axis is efficiently amplified, facilitating simultaneous dual-axis actuation. Experimental results show that the mirror exhibits dual resonant frequencies of approximately 111 and 168 Hz, with the HR array providing acoustic amplification of up to 34 dB, resulting in projected laser patterns orthogonal in two modes. The proposed approach overcomes the limitations of conventional acoustic actuation and provides an effective strategy for enhancing multiaxis MEMS-mirror performance using acoustic metamaterials.

  • Biaxial Optical Cantilever Combining On-Chip Patterned Laser and Sampling Moiré Method

    by Soya Sato, Toshihiro Shiratori, Kazuyoshi Hirose, Hiroki Kumon, Hiroki Kamei, Shu Honma, Yuki Okamoto, Yusuke Takei, Hidetoshi Takahashi

    The optical lever method is a widely used high-resolution displacement sensing technique in various micro- and nanoscale sensing systems. In this method, cantilever displacement is evaluated by detecting changes in the position of reflected light using a photodiode; however, precise optical alignment is required during setup. To address this issue, optical lever systems combining a cantilever with the sampling moiré (SM) method have been proposed. More recently, approaches using on-chip pattern lasers that directly project periodic patterns have attracted attention, as they simplify both system configuration and cantilever fabrication. In many applications, not only normal displacement but also torsional deformation must be measured to evaluate multi-axis forces and moments. Although the SM method is well suited for analyzing two-dimensional periodic patterns, generating well-defined two-dimensional lattice patterns using mechanical gratings is technically challenging. In this study, we propose a biaxial optical cantilever sensor that integrates the SM method with an on-chip pattern laser capable of directly projecting a two-dimensional checkerboard pattern. The projected pattern was captured using a lens-less camera and analyzed using the SM method. Experimental results confirmed that the checkerboard pattern shifted independently in two directions depending on the force application point. The achieved resolutions were 32.4 nN for the normal force Fz and 201 μN·μm for the bending moment Mx, demonstrating the feasibility of simple and high-resolution two-axis force measurement.

  • Open Access

    Direct phase-compensation method of piezoelectric resonant MEMS scanners through control of driving signal phase and duty cycle

    by Yuki Okamoto, Rihachiro Nakashima, Ryo Oda, Kei Ohara, Soya Sato, Sucheta Gorwadkar, Hironao Okada, Yusuke Takei

    Piezoelectric actuators are integral to microelectromechanical systems (MEMS) scanners, but phase errors can impair laser scanning accuracy. This study addresses these errors through direct compensation methods, eliminating the need for embedded phase-detection sensors, which complicate fabrication and design. Specifically, we explored the influence of driving-signal modulation on the phase shift between the applied voltage and resulting scanning angle. Our experiments reveal that adjusting the phase difference yields the best compensation, effectively reducing phase error while maintaining scanning performance. These results validate a sensorless approach to improve laser scanning precision in piezoelectric MEMS scanners without added fabrication complexity.