Fakai Dou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fakai Dou has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Tian Su
Department of Civil Engineering, School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
2 shared publications - Xuefeng Mei
College of Civil Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China
2 shared publications - Bangxiang Li
School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
1 shared publication - Deqiang Yang
School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
1 shared publication - Jianping Liu
School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
1 shared publication - Meiyan Wang
Department of Civil Engineering, Shandong Vocational College of Science and Technology, Weifang 261053, China
1 shared publication
Latest Publications
- Open Access
Thermal Analysis and Thermal–Mechanical Stress Simulation of Polycrystalline Diamond Compact Bits During Rock Breaking Process
Polycrystalline diamond compact (PDC) bits are widely used in oil, gas, and geological exploration. During rock breaking, most of the work is converted into cutting heat, leading to a rise in cutter temperature and potential damage. However, the influence of formation temperature and rock properties on cutting temperature and thermal stress remains insufficiently understood. This study combined numerical simulation and experimental methods to investigate the temperature rise and thermal stress of a single PDC cutter during rock breaking, focusing on the effects of formation temperature (27–250 °C) and rock strength (sandstone, marble, and granite). The results show that the temperature rise of the PDC cutter adheres to the following three distinct stages: rapid increase, slow increase, and stabilization. Rock strength significantly affects the temperature rise rate and stress; when breaking granite, the cutter temperature reached approximately 131.4 °C, about 2–3 times higher than for marble and sandstone, while the rate of penetration (ROP) decreased by 70.6–75.6%. As formation temperature increased from 27 °C to 250 °C, the internal temperature difference within the cutter decreased from 72.6 °C to 35.6 °C, and the equivalent stress first increased and then decreased, peaking at 2.84 GPa at 50 °C. The ROP initially increased and then decreased with an increase in formation temperature. Numerical simulations and experimental findings are in good agreement. This study provides theoretical and technical guidance for optimizing cutter design and improving the rock-breaking efficiency and service life of PDC bits in deep and high-temperature formations.
Open AccessThermal Analysis and Thermal–Mechanical Stress Simulation of Polycrystalline Diamond Compact Bits During Rock Breaking Process
Polycrystalline diamond compact (PDC) bits are widely used in oil, gas, and geological exploration. During rock breaking, most of the work is converted into cutting heat, leading to a rise in cutter temperature and potential damage. However, the influence of formation temperature and rock properties on cutting temperature and thermal stress remains insufficiently understood. This study combined numerical simulation and experimental methods to investigate the temperature rise and thermal stress of a single PDC cutter during rock breaking, focusing on the effects of formation temperature (27–250 °C) and rock strength (sandstone, marble, and granite). The results show that the temperature rise of the PDC cutter adheres to the following three distinct stages: rapid increase, slow increase, and stabilization. Rock strength significantly affects the temperature rise rate and stress; when breaking granite, the cutter temperature reached approximately 131.4 °C, about 2–3 times higher than for marble and sandstone, while the rate of penetration (ROP) decreased by 70.6–75.6%. As formation temperature increased from 27 °C to 250 °C, the internal temperature difference within the cutter decreased from 72.6 °C to 35.6 °C, and the equivalent stress first increased and then decreased, peaking at 2.84 GPa at 50 °C. The ROP initially increased and then decreased with an increase in formation temperature. Numerical simulations and experimental findings are in good agreement. This study provides theoretical and technical guidance for optimizing cutter design and improving the rock-breaking efficiency and service life of PDC bits in deep and high-temperature formations.
- Open Access
Model of Mechanical Properties of Concrete in Western Saline Soil Regions Based on Grey Theory
Concrete structures in western saline soil regions are subjected to extreme environments with coupled dry-wet cycles and high concentrations of erosive ions such as Cl−, SO42−, and Mg2+, leading to severe degradation of mechanical properties. This study employed a simulated accelerated, high-concentration solution (Solution A, ~8× seawater salinity) similar to the composition of actual saline soil to perform accelerated dry-wet cycling corrosion tests on ordinary C40 concrete specimens for six corrosion ages (0, 5, 8, 10, 15, and 20 months). For each age, three replicate cube specimens were tested per property. The changes in cube compressive strength, splitting tensile strength, prism stress–strain full curves, and microstructure were systematically investigated. Results show that in the initial corrosion stage (0–5 months), strength exhibits a brief increase (compressive strength by 11.87%, splitting tensile strength by 9.23%) due to pore filling by corrosion products such as ettringite, gypsum, and Friedel’s salt. It then enters a slow deterioration stage (5–15 months), with significant strength decline by 20 months, where splitting tensile strength is most sensitive to corrosion. Long-term prediction models for key parameters such as compressive strength, splitting tensile strength, elastic modulus, peak stress, and peak strain were established based on grey GM(1,1) theory using the measured data from 0 to 20 months, achieving “excellent” accuracy (C ≤ 0.1221, p = 1). A segmented compressive constitutive model that considers the effect of corrosion time was proposed by combining continuous damage mechanics and the Weibull distribution. The ascending branch showed high consistency with the experimental curves. Life prediction indicates that under natural dry-wet cycling conditions, the service life of ordinary concrete in this region is only about 7.5 years when splitting tensile strength drops to 50% of initial value as the failure criterion, far below the 50-year design benchmark period. This study provides reliable theoretical models and a quantitative basis for durability design and life assessment of concrete structures in western saline soil regions.
Open AccessModel of Mechanical Properties of Concrete in Western Saline Soil Regions Based on Grey Theory
Concrete structures in western saline soil regions are subjected to extreme environments with coupled dry-wet cycles and high concentrations of erosive ions such as Cl−, SO42−, and Mg2+, leading to severe degradation of mechanical properties. This study employed a simulated accelerated, high-concentration solution (Solution A, ~8× seawater salinity) similar to the composition of actual saline soil to perform accelerated dry-wet cycling corrosion tests on ordinary C40 concrete specimens for six corrosion ages (0, 5, 8, 10, 15, and 20 months). For each age, three replicate cube specimens were tested per property. The changes in cube compressive strength, splitting tensile strength, prism stress–strain full curves, and microstructure were systematically investigated. Results show that in the initial corrosion stage (0–5 months), strength exhibits a brief increase (compressive strength by 11.87%, splitting tensile strength by 9.23%) due to pore filling by corrosion products such as ettringite, gypsum, and Friedel’s salt. It then enters a slow deterioration stage (5–15 months), with significant strength decline by 20 months, where splitting tensile strength is most sensitive to corrosion. Long-term prediction models for key parameters such as compressive strength, splitting tensile strength, elastic modulus, peak stress, and peak strain were established based on grey GM(1,1) theory using the measured data from 0 to 20 months, achieving “excellent” accuracy (C ≤ 0.1221, p = 1). A segmented compressive constitutive model that considers the effect of corrosion time was proposed by combining continuous damage mechanics and the Weibull distribution. The ascending branch showed high consistency with the experimental curves. Life prediction indicates that under natural dry-wet cycling conditions, the service life of ordinary concrete in this region is only about 7.5 years when splitting tensile strength drops to 50% of initial value as the failure criterion, far below the 50-year design benchmark period. This study provides reliable theoretical models and a quantitative basis for durability design and life assessment of concrete structures in western saline soil regions.