Ximing Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ximing Yang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Jichun Yang
School of Rare Earth Industry Inner Mongolia University of Science and Technology Baotou China
2 shared publicationsPeng Sun
China Satellite Network Group Co. Ltd. Beijing China
2 shared publicationsGuangqian Feng
Inner Mongolia University of Science and Technology
1 shared publicationLei Ren
Inner Mongolia University of Science and Technology
1 shared publication- Lei Ren
School of Rare Earth Industry Inner Mongolia University of Science and Technology Baotou China
1 shared publication Yubao Liu
State Key Laboratory of Baiyunobo Rare Earth Resource Researches and Comprehensive Utilization Baotou Research Institute of Rare Earths Baotou P.R. China
1 shared publication
Latest Publications
- 7 March 2026
- Published by Wiley in Steel Research International
- Vol. 97 (9) , 4844-4861
Synergistic Regulation of Inclusion Characteristics by La–Ce Mixed Rare Earth and Its Impact on the Mechanical Properties of U71Mn Steel
This study investigates the synergistic effects of the O/S ratio and La–Ce mixed rare earths on the inclusion occurrence state and mechanical properties of U71Mn steel. Thermodynamic calculations based on the Wagner model and Factsage reveal the formation sequence and stability of rare‐earth inclusions, indicating that La exhibits higher activity than Ce and preferentially forms fine and stable (La, Ce) 2 O 2 S inclusions under low O/S conditions. When O/S ≤ 0.75 and the rare earth content ≥ 0.015%, MnS can be completely modified, and the inclusions transform from elongated or composite types into refined and spherical morphologies, significantly improving steel cleanliness. Microstructural observations show that rare earths promote grain refinement and reduce interfacial stress concentration. Mechanical tests demonstrate that rare earth modification increases hardness and reduces its fluctuation, enhances impact toughness by 22%–112%, and improves yield and tensile strengths by 7%–13% and 1%–8%, respectively. The friction coefficient decreases by 10%–40%, indicating improved wear resistance. These results confirm that regulating the O/S ratio and La/Ce proportion enables controlled inclusion evolution and comprehensive improvement of the strength, toughness, and wear performance of U71Mn steel.
- 7 March 2026
- Published by Wiley in Steel Research International
- Vol. 97 (9) , 4844-4861
Synergistic Regulation of Inclusion Characteristics by La–Ce Mixed Rare Earth and Its Impact on the Mechanical Properties of U71Mn Steel
This study investigates the synergistic effects of the O/S ratio and La–Ce mixed rare earths on the inclusion occurrence state and mechanical properties of U71Mn steel. Thermodynamic calculations based on the Wagner model and Factsage reveal the formation sequence and stability of rare‐earth inclusions, indicating that La exhibits higher activity than Ce and preferentially forms fine and stable (La, Ce) 2 O 2 S inclusions under low O/S conditions. When O/S ≤ 0.75 and the rare earth content ≥ 0.015%, MnS can be completely modified, and the inclusions transform from elongated or composite types into refined and spherical morphologies, significantly improving steel cleanliness. Microstructural observations show that rare earths promote grain refinement and reduce interfacial stress concentration. Mechanical tests demonstrate that rare earth modification increases hardness and reduces its fluctuation, enhances impact toughness by 22%–112%, and improves yield and tensile strengths by 7%–13% and 1%–8%, respectively. The friction coefficient decreases by 10%–40%, indicating improved wear resistance. These results confirm that regulating the O/S ratio and La/Ce proportion enables controlled inclusion evolution and comprehensive improvement of the strength, toughness, and wear performance of U71Mn steel.
- 16 December 2025
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Effect of O/S and Ce/La ratio on the occurrence state of inclusions in U75V steel
Non-metallic inclusions in steel have a significant impact on the comprehensive properties of the steel. Although it is not possible to completely remove these inclusions, their impact on mechanical properties can be mitigated by controlling their morphology, quantity, and other characteristics. This study focuses on the oxygen-to-sulphur (O/S) ratio and the lanthanum-to-cerium (Ce/La) ratio as key factors and designs an orthogonal experiment with three factors at four levels. Using FactSage 7.1, the composition of inclusions in steel was calculated for 80 sets of compositions, analysing the state of inclusions in U75V steel under different O/S and Ce/La ratios. Within the national standard composition control range for U75V steel, when the total rare earth content in the steel is less than 0.015% and 0.045 < O/S < 0.075, if Ce/La > 3, the inclusions in the steel mainly exist in the form of Ce 2 O 2 S, La 2 S 3 , Ce 2 S 3 , and MnS; if 1 < Ce/La < 3, and if the O/Al ratio in the steel is greater than 0.52, Ce 2 S 3 is replaced by Al 2 O 3 ; if Ce/La < 1, Ce2S3 does not exist in the steel. When the O/S ratio in the steel is greater than 0.5, and the total rare earth content reaches 0.015%, MnS inclusions completely disappear, and the sulphides in the steel are mainly rare earth sulphides and oxysulphides; for 0.5 < O/S < 2, and Ce/La > 3, the inclusions in the steel mainly exist in the form of Ce 2 O 2 S, La 2 O 2 S, Ce 2 S 3 , and La 2 S 3 ; for 0.5 < O/S < 2, and 1 < Ce/La < 3, if the O/Al ratio in the steel is greater than 3, Ce 2 S 3 is replaced by Al 2 O 3 ; for 0.5 < O/S < 2, and Ce/La < 1, the inclusions in the steel mainly exist in the form of Ce 2 O 2 S, La 2 O 2 S, Ce 2 S 3 , and La 2 S 3 , with Al 2 O 3 disappearing. To verify the thermodynamic predictions of the state of inclusions in U75V steel under different O/S and Ce/La ratios, vacuum induction melting was used to smelt U75V steel containing lanthanum and cerium. Sample 2# had an O/S ratio of 1.05 and a Ce/La ratio of 0.514, with inclusions mainly existing as Ce 2 O 2 S and La 2 O 2 S; Sample 3# had an O/S ratio of 1.33 and a Ce/La ratio of 0.115, with inclusions also mainly existing as Ce 2 O 2 S and La 2 O 2 S, confirming the computational results of the thermodynamic predictions for the state of inclusions under different O/S and Ce/La ratios.
- 16 December 2025
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Effect of O/S and Ce/La ratio on the occurrence state of inclusions in U75V steel
Non-metallic inclusions in steel have a significant impact on the comprehensive properties of the steel. Although it is not possible to completely remove these inclusions, their impact on mechanical properties can be mitigated by controlling their morphology, quantity, and other characteristics. This study focuses on the oxygen-to-sulphur (O/S) ratio and the lanthanum-to-cerium (Ce/La) ratio as key factors and designs an orthogonal experiment with three factors at four levels. Using FactSage 7.1, the composition of inclusions in steel was calculated for 80 sets of compositions, analysing the state of inclusions in U75V steel under different O/S and Ce/La ratios. Within the national standard composition control range for U75V steel, when the total rare earth content in the steel is less than 0.015% and 0.045 < O/S < 0.075, if Ce/La > 3, the inclusions in the steel mainly exist in the form of Ce 2 O 2 S, La 2 S 3 , Ce 2 S 3 , and MnS; if 1 < Ce/La < 3, and if the O/Al ratio in the steel is greater than 0.52, Ce 2 S 3 is replaced by Al 2 O 3 ; if Ce/La < 1, Ce2S3 does not exist in the steel. When the O/S ratio in the steel is greater than 0.5, and the total rare earth content reaches 0.015%, MnS inclusions completely disappear, and the sulphides in the steel are mainly rare earth sulphides and oxysulphides; for 0.5 < O/S < 2, and Ce/La > 3, the inclusions in the steel mainly exist in the form of Ce 2 O 2 S, La 2 O 2 S, Ce 2 S 3 , and La 2 S 3 ; for 0.5 < O/S < 2, and 1 < Ce/La < 3, if the O/Al ratio in the steel is greater than 3, Ce 2 S 3 is replaced by Al 2 O 3 ; for 0.5 < O/S < 2, and Ce/La < 1, the inclusions in the steel mainly exist in the form of Ce 2 O 2 S, La 2 O 2 S, Ce 2 S 3 , and La 2 S 3 , with Al 2 O 3 disappearing. To verify the thermodynamic predictions of the state of inclusions in U75V steel under different O/S and Ce/La ratios, vacuum induction melting was used to smelt U75V steel containing lanthanum and cerium. Sample 2# had an O/S ratio of 1.05 and a Ce/La ratio of 0.514, with inclusions mainly existing as Ce 2 O 2 S and La 2 O 2 S; Sample 3# had an O/S ratio of 1.33 and a Ce/La ratio of 0.115, with inclusions also mainly existing as Ce 2 O 2 S and La 2 O 2 S, confirming the computational results of the thermodynamic predictions for the state of inclusions under different O/S and Ce/La ratios.