Andrii Yavtushenko
Andrii Yavtushenko has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Serhii Hubskyi
National Technical University “Kharkiv Polytechnic Institute”
4 shared publications - Yuriy Babay
National Technical University “Kharkiv Polytechnic Institute”
3 shared publications - Dmytro Borodin
Machine Components and Hydropneumatic Systems Department; National Technical University “Kharkiv Polytechnic Institute
1 shared publication Dmytro Cherkashyn
1 shared publication- Dmytro V. Cherkashyn1 shared publication
- Gennady Kulik
National Technical University “Kharkiv Polytechnic Institute
1 shared publication
Latest Publications
- Open Access
- 29 June 2026
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 27 (2) , 1-12
Machine learning-based diagnosis of sliding bearings in rolling mill drive systems under severe operating conditions
- 29 June 2026
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 27 (2) , 1-12
Open AccessMachine learning-based diagnosis of sliding bearings in rolling mill drive systems under severe operating conditions
- Open Access
- 7 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 2(12),p. 163-173
COMPARATIVE ANALYSIS OF VIBRATIONS USING FAST FOURIER TRANSFORM AND WAVELET TRANSFORM
The article examines the application of vibration signal processing methods for diagnosing the technical condition of rotor systems. A comparative analysis of the Fast Fourier Transform (FFT), Continuous Wavelet Transform (CWT), and Discrete Wavelet Transform (DWT) was conducted to detect anomalies and impulsive disturbances. FFT enables the evaluation of the spectral content of a signal but lacks time localization of frequency components. In contrast, CWT and DWT provide time-frequency localization and allow the identification of hidden defects, which is crucial for analyzing non-stationary processes. Experimental results obtained from the RK-4 test bench confirm the effectiveness of wavelet analysis for high-speed rotor operation and modeling of faults such as imbalance, cracks, or friction. The proposed combination of methods improves diagnostic accuracy and enables efficient condition monitoring of equipment.
- 7 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 2(12),p. 163-173
Open AccessCOMPARATIVE ANALYSIS OF VIBRATIONS USING FAST FOURIER TRANSFORM AND WAVELET TRANSFORM
The article examines the application of vibration signal processing methods for diagnosing the technical condition of rotor systems. A comparative analysis of the Fast Fourier Transform (FFT), Continuous Wavelet Transform (CWT), and Discrete Wavelet Transform (DWT) was conducted to detect anomalies and impulsive disturbances. FFT enables the evaluation of the spectral content of a signal but lacks time localization of frequency components. In contrast, CWT and DWT provide time-frequency localization and allow the identification of hidden defects, which is crucial for analyzing non-stationary processes. Experimental results obtained from the RK-4 test bench confirm the effectiveness of wavelet analysis for high-speed rotor operation and modeling of faults such as imbalance, cracks, or friction. The proposed combination of methods improves diagnostic accuracy and enables efficient condition monitoring of equipment.
- 30 December 2025
- Published by Admiral Makarov National University of Shipbuilding in Collection of Scientific Publications NUS
- No. 4 (502),p. 89-98
ANALYSIS OF BEARING VIBRATION SIGNALS USING THE RMS METHOD
- 30 December 2025
- Published by Admiral Makarov National University of Shipbuilding in Collection of Scientific Publications NUS
- No. 4 (502),p. 89-98
ANALYSIS OF BEARING VIBRATION SIGNALS USING THE RMS METHOD
- Open Access
- 30 June 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 2,p. 75-80
Simulation of roll forming for U-shaped bent profiles
Purpose. To develop an approach for simulating the roll forming process of U-shaped bent profiles using the QForm software package. Methodology. The study is based on the finite element method implemented in QForm. The process was simulated in a 3D environment, accounting for elastic–plastic deformation, using a single operation of the «Sheet Bulk Forming» type. A sequential forming scheme was implemented using 12 roll stands, which incorporated the elastic–plastic properties of the material. Appropriate boundary conditions were defined to replicate real technological parameters of the roll forming process. Results. The simulation yielded stress and strain distributions in the blank at various stages of its passage through the roll stands. It was found that maximum plastic strains occur in the bending zones, while the edge regions are predominantly subjected to tensile stresses. The simulation results are consistent with the physical nature of the bending process and confirm the validity of the proposed approach. Scientific Novelty. An adaptation of the QForm software package is proposed for simulating the roll forming of bent profiles, which is not covered by its standard modules. Simulation algorithm and boundary condition setup were developed, enabling the analysis of the stress–strain state of the blank during profile formation. Practical Significance. The results of the study can be used to optimize technological parameters of the roll forming process, reduce the likelihood of defect formation, and expand the functional capabilities of QForm in the field of sheet metal forming simulation. The proposed approach is valuable for technologists, engineers, designers, and researchers working in the field of metal forming.
- 30 June 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 2,p. 75-80
Open AccessSimulation of roll forming for U-shaped bent profiles
Purpose. To develop an approach for simulating the roll forming process of U-shaped bent profiles using the QForm software package. Methodology. The study is based on the finite element method implemented in QForm. The process was simulated in a 3D environment, accounting for elastic–plastic deformation, using a single operation of the «Sheet Bulk Forming» type. A sequential forming scheme was implemented using 12 roll stands, which incorporated the elastic–plastic properties of the material. Appropriate boundary conditions were defined to replicate real technological parameters of the roll forming process. Results. The simulation yielded stress and strain distributions in the blank at various stages of its passage through the roll stands. It was found that maximum plastic strains occur in the bending zones, while the edge regions are predominantly subjected to tensile stresses. The simulation results are consistent with the physical nature of the bending process and confirm the validity of the proposed approach. Scientific Novelty. An adaptation of the QForm software package is proposed for simulating the roll forming of bent profiles, which is not covered by its standard modules. Simulation algorithm and boundary condition setup were developed, enabling the analysis of the stress–strain state of the blank during profile formation. Practical Significance. The results of the study can be used to optimize technological parameters of the roll forming process, reduce the likelihood of defect formation, and expand the functional capabilities of QForm in the field of sheet metal forming simulation. The proposed approach is valuable for technologists, engineers, designers, and researchers working in the field of metal forming.