Gennady Kulik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gennady Kulik has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Anatoliy Gaydamaka
National Technical University “Kharkiv Polytechnic Institute
3 shared publications - Serhii Bobrytskyi
National Technical University “Kharkiv Polytechnic Institute
2 shared publications - Volodymyr Klitnoi
National technical university «Kharkiv polytechnic institute
2 shared publications - Andrii Lukashov
National Technical University “Kharkiv Polytechnic Institute
1 shared publication - Andrii Rogovyi
National Technical University Kharkiv Polytechnic Institute
1 shared publication - Andrii Yavtushenko1 shared publication
Latest Publications
- 1 October 2025
- Published by Springer Nature
- p. 204-214
The Technical Condition Monitoring Model of Large Module Gears
- 1 October 2025
- Published by Springer Nature
- p. 204-214
The Technical Condition Monitoring Model of Large Module Gears
- Open Access
- 30 June 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 2,p. 75-80
Simulation of roll forming for U-shaped bent profiles
Purpose. To develop an approach for simulating the roll forming process of U-shaped bent profiles using the QForm software package. Methodology. The study is based on the finite element method implemented in QForm. The process was simulated in a 3D environment, accounting for elastic–plastic deformation, using a single operation of the «Sheet Bulk Forming» type. A sequential forming scheme was implemented using 12 roll stands, which incorporated the elastic–plastic properties of the material. Appropriate boundary conditions were defined to replicate real technological parameters of the roll forming process. Results. The simulation yielded stress and strain distributions in the blank at various stages of its passage through the roll stands. It was found that maximum plastic strains occur in the bending zones, while the edge regions are predominantly subjected to tensile stresses. The simulation results are consistent with the physical nature of the bending process and confirm the validity of the proposed approach. Scientific Novelty. An adaptation of the QForm software package is proposed for simulating the roll forming of bent profiles, which is not covered by its standard modules. Simulation algorithm and boundary condition setup were developed, enabling the analysis of the stress–strain state of the blank during profile formation. Practical Significance. The results of the study can be used to optimize technological parameters of the roll forming process, reduce the likelihood of defect formation, and expand the functional capabilities of QForm in the field of sheet metal forming simulation. The proposed approach is valuable for technologists, engineers, designers, and researchers working in the field of metal forming.
- 30 June 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 2,p. 75-80
Open AccessSimulation of roll forming for U-shaped bent profiles
Purpose. To develop an approach for simulating the roll forming process of U-shaped bent profiles using the QForm software package. Methodology. The study is based on the finite element method implemented in QForm. The process was simulated in a 3D environment, accounting for elastic–plastic deformation, using a single operation of the «Sheet Bulk Forming» type. A sequential forming scheme was implemented using 12 roll stands, which incorporated the elastic–plastic properties of the material. Appropriate boundary conditions were defined to replicate real technological parameters of the roll forming process. Results. The simulation yielded stress and strain distributions in the blank at various stages of its passage through the roll stands. It was found that maximum plastic strains occur in the bending zones, while the edge regions are predominantly subjected to tensile stresses. The simulation results are consistent with the physical nature of the bending process and confirm the validity of the proposed approach. Scientific Novelty. An adaptation of the QForm software package is proposed for simulating the roll forming of bent profiles, which is not covered by its standard modules. Simulation algorithm and boundary condition setup were developed, enabling the analysis of the stress–strain state of the blank during profile formation. Practical Significance. The results of the study can be used to optimize technological parameters of the roll forming process, reduce the likelihood of defect formation, and expand the functional capabilities of QForm in the field of sheet metal forming simulation. The proposed approach is valuable for technologists, engineers, designers, and researchers working in the field of metal forming.
- Open Access
- 1 February 2025
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 26 (1) , 1-9
Study of the functioning and wear of the teeth of the intermediate gear of the vertical gearbox rolls of the slabing state - 1150
Gears with large modules are widely used in heavy engineering, for example in rolling mills. The unpredictability of mechanical equipment overloads or operator error lead to premature failure, first of all, of typical parts like gear wheels. This article analyzes the nature of the wear of the...
- 1 February 2025
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 26 (1) , 1-9
Open AccessStudy of the functioning and wear of the teeth of the intermediate gear of the vertical gearbox rolls of the slabing state - 1150
Gears with large modules are widely used in heavy engineering, for example in rolling mills. The unpredictability of mechanical equipment overloads or operator error lead to premature failure, first of all, of typical parts like gear wheels. This article analyzes the nature of the wear of the...
- Open Access
- 22 May 2019
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (99)) , 6-10
Devising an engineering procedure for calculating the ductility of a roller bearing under a no-central radial load
Devising an engineering procedure for calculating the ductility of a roller bearing under a no-central radial load
- 22 May 2019
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (99)) , 6-10
Open AccessDevising an engineering procedure for calculating the ductility of a roller bearing under a no-central radial load
Devising an engineering procedure for calculating the ductility of a roller bearing under a no-central radial load