R. Konishi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
R. Konishi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Hiromasa Sasa
Kyushu University, Fukuoka, Japan
2 shared publications - Hiroshi Miyazaki
Kyushu University, Fukuoka, Japan
2 shared publications - Masataka Iwakuma
Kyushu University, Fukuoka, Japan
2 shared publications H. Handa
Kyushu University, Fukuoka, Japan
1 shared publicationK. Yoshida
Kyushu University, Fukuoka, Japan
1 shared publicationM. Konno
Kyushu University, Fukuoka, Japan
1 shared publication
Latest Publications
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Fabrication and Testing of Prototype Saddle-Shaped Field and Distributed Armature Coils for a 2-MW REBCO Synchronous Generator
Achieving carbon-neutral growth in the aviation sector demands innovative propulsion technologies, with electric propulsion systems offering a particularly promising solution. To advance this goal, we are developing a 2-MW fully superconducting synchronous generator that employs REBa2Cu3O7-δ (REBCO) tapes. The generator is designed as a two-pole machine operating at 3,600 rpm. Its field coil adopts a saddle-shaped winding mounted on a through-shaft, which enables stable high-speed rotation, while the armature employs a distributed winding in which the U, V, and W phases overlap adjacent phases by 60°, thereby enhancing output performance. Each armature winding uses a parallel conductor composed of 20 stacked Face-to-Face Double Stacked (FFDS) rare-earth barium copper oxide (REBCO) tapes, enabling efficient conduction of large AC currents. Because degradation of the critical current (Ic) in the REBCO tape would compromise generator performance, prototype field and armature coils were fabricated and tested to confirm winding feasibility. The field coil, wound with 3.2 km of FFDS REBCO tape, showed no voltage generation up to 75 A, and the high n-values verified the absence of degradation. For the armature, one prototype coil was fabricated using a transposed 20-tape conductor, each tape 40 m in length. V–I measurements of all 20 tapes demonstrated no Ic degradation. These findings confirm the feasibility of employing FFDS REBCO tapes in large-scale, three-dimensional windings without Ic degradation, thereby providing a strong foundation for the development of the 2-MW fully superconducting synchronous generator.
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Fabrication and Testing of Prototype Saddle-Shaped Field and Distributed Armature Coils for a 2-MW REBCO Synchronous Generator
Achieving carbon-neutral growth in the aviation sector demands innovative propulsion technologies, with electric propulsion systems offering a particularly promising solution. To advance this goal, we are developing a 2-MW fully superconducting synchronous generator that employs REBa2Cu3O7-δ (REBCO) tapes. The generator is designed as a two-pole machine operating at 3,600 rpm. Its field coil adopts a saddle-shaped winding mounted on a through-shaft, which enables stable high-speed rotation, while the armature employs a distributed winding in which the U, V, and W phases overlap adjacent phases by 60°, thereby enhancing output performance. Each armature winding uses a parallel conductor composed of 20 stacked Face-to-Face Double Stacked (FFDS) rare-earth barium copper oxide (REBCO) tapes, enabling efficient conduction of large AC currents. Because degradation of the critical current (Ic) in the REBCO tape would compromise generator performance, prototype field and armature coils were fabricated and tested to confirm winding feasibility. The field coil, wound with 3.2 km of FFDS REBCO tape, showed no voltage generation up to 75 A, and the high n-values verified the absence of degradation. For the armature, one prototype coil was fabricated using a transposed 20-tape conductor, each tape 40 m in length. V–I measurements of all 20 tapes demonstrated no Ic degradation. These findings confirm the feasibility of employing FFDS REBCO tapes in large-scale, three-dimensional windings without Ic degradation, thereby providing a strong foundation for the development of the 2-MW fully superconducting synchronous generator.
- 19 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Design of Shortened REBa 2 Cu 3 O 7-δ Saddle-Shaped Field Coil Ends for Fully Superconducting Synchronous Motors Using Generalized Flatwise Curvature
To reduce carbon dioxide emissions from aircraft, superconducting electric propulsion systems are attracting attention. For aircraft, high power density is particularly important, and increasing the power density requires higher rotational speed. Therefore, we are studying a saddle-shaped field coil made with REBa2Cu3O7-δ (REBCO) tape. This coil can be fixed directly to the shaft, which helps provide the mechanical strength needed for high-speed rotation. However, because of the shape characteristics of the REBCO tape, the coil ends tend to become long, increasing the axial length of the motor. In addition, excessive bending or twisting can damage the tape; thus, careful design is necessary. In this study, we developed a design method to shorten the saddle-shaped field coil and evaluated its electromagnetic performance. We introduced a generalized flatwise curvature to represent bending and twisting and set the allowable curvature of the REBCO tape to 0.1 mm-1 based on its mechanical limits. Using this condition, we designed two types of shortened coils. Model A arranges the coils based on the curvature of the innermost coil, while Model B equalizes the curvature of all coils to prevent interference at the coil ends. Three-dimensional finite-element analysis revealed that the axial gap flux density distribution of both models is almost the same. However, Model B has a slightly larger high-flux-density region because its straight part is longer, resulting in better output performance. The obtained torque also exhibits a strong proportional relationship with the axial integral of the gap flux density, confirming that the coil ends are important regions that contribute to motor output.
- 19 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Design of Shortened REBa 2 Cu 3 O 7-δ Saddle-Shaped Field Coil Ends for Fully Superconducting Synchronous Motors Using Generalized Flatwise Curvature
To reduce carbon dioxide emissions from aircraft, superconducting electric propulsion systems are attracting attention. For aircraft, high power density is particularly important, and increasing the power density requires higher rotational speed. Therefore, we are studying a saddle-shaped field coil made with REBa2Cu3O7-δ (REBCO) tape. This coil can be fixed directly to the shaft, which helps provide the mechanical strength needed for high-speed rotation. However, because of the shape characteristics of the REBCO tape, the coil ends tend to become long, increasing the axial length of the motor. In addition, excessive bending or twisting can damage the tape; thus, careful design is necessary. In this study, we developed a design method to shorten the saddle-shaped field coil and evaluated its electromagnetic performance. We introduced a generalized flatwise curvature to represent bending and twisting and set the allowable curvature of the REBCO tape to 0.1 mm-1 based on its mechanical limits. Using this condition, we designed two types of shortened coils. Model A arranges the coils based on the curvature of the innermost coil, while Model B equalizes the curvature of all coils to prevent interference at the coil ends. Three-dimensional finite-element analysis revealed that the axial gap flux density distribution of both models is almost the same. However, Model B has a slightly larger high-flux-density region because its straight part is longer, resulting in better output performance. The obtained torque also exhibits a strong proportional relationship with the axial integral of the gap flux density, confirming that the coil ends are important regions that contribute to motor output.