Yakup Daşdemirli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yakup Daşdemirli has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Muhammet Kayfeci
Karabuk University
3 shared publications - Ulaş Matik
Karabuk University
3 shared publications - Abdullah Dağdeviren
Karabuk University
1 shared publication - Bahadir Acar
Karabuk University
1 shared publication - Megen Guled Mohammed
Karabuk University
1 shared publication - Mustafa Yaşar
Department of Industrial Design Engineering, Karabük University, Karabük 78050, Turkey
1 shared publication
Latest Publications
- Open Access
- 17 July 2026
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 12 (5) , 1723
Experimental and mathematical modeling analysis of freeze-drying kinetics for ginger slices with different thickness
In this study, the freeze-drying (FD) behavior of ginger (Zingiber officinale) at thicknesses of 5 and 7 mm was analyzed experimentally and statistically. The drying process was evaluated using ten empirical models to decide which was most proper for predicting weight reduction. Among the evaluated models, the Logarithmic Model was the most correct in describing the drying kinetics for both sample thicknesses, showing the lowest error rates of 8.39% for 5 mm samples and 8.42% for 7 mm samples. The 5 mm samples had statistical parameters of correlation coefficient (R2) = 0.9902, chi-square (X2) = 1.402×10-3 and root mean square error (RMSE) = 0.03211. The 7 mm samples had R2 = 0.9986, X2= 1.153×10-3, and RMSE = 0.03411. Additionally, the calculated effective moisture diffusion coefficient (Deff) values for 5 mm and 7 mm were 2.075×10-7 m2/s and 4.079×10-10 m2/s, respectively, which are in line with the values reported for different food items.
- 17 July 2026
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 12 (5) , 1723
Open AccessExperimental and mathematical modeling analysis of freeze-drying kinetics for ginger slices with different thickness
In this study, the freeze-drying (FD) behavior of ginger (Zingiber officinale) at thicknesses of 5 and 7 mm was analyzed experimentally and statistically. The drying process was evaluated using ten empirical models to decide which was most proper for predicting weight reduction. Among the evaluated models, the Logarithmic Model was the most correct in describing the drying kinetics for both sample thicknesses, showing the lowest error rates of 8.39% for 5 mm samples and 8.42% for 7 mm samples. The 5 mm samples had statistical parameters of correlation coefficient (R2) = 0.9902, chi-square (X2) = 1.402×10-3 and root mean square error (RMSE) = 0.03211. The 7 mm samples had R2 = 0.9986, X2= 1.153×10-3, and RMSE = 0.03411. Additionally, the calculated effective moisture diffusion coefficient (Deff) values for 5 mm and 7 mm were 2.075×10-7 m2/s and 4.079×10-10 m2/s, respectively, which are in line with the values reported for different food items.
- 1 March 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Electrochemistry
- Vol. 62 (3) , 131-141
Electrochemical Characterization of 316L Stainless Steel Electrodes for Alkaline Water Electrolysis in Renewable Energy Applications
- 1 March 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Electrochemistry
- Vol. 62 (3) , 131-141
Electrochemical Characterization of 316L Stainless Steel Electrodes for Alkaline Water Electrolysis in Renewable Energy Applications
- 20 February 2026
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- No. Advanced O,p. 1
Enhancing the Hydrogen Storage Performance of LaNi5 Metal Hydrides via Cu, Cu/Ag and Ag Coatings with Improved Thermal Conductivity
This study investigates the thermal and mass transfer behaviors of the LaNi5 alloy during hydrogen absorption after applying three different surface coatings. To enhance heat transfer within the metal hydride reactor and evaluate its performance, three reactor designs were developed: a reference design, a design incorporating a central heat pipe, and an advanced design equipped with a finned heat pipe to improve heat distribution. LaNi5 powders were ground for one hour using mechanical milling and then coated under controlled conditions to produce copper-coated, Cu/Ag double-layer-coated, and silver-coated samples. The findings demonstrate that a homogeneous and stable Cu/Ag duplex coating can be successfully applied to LaNi5 powders. This offers the potential to enhance heat transfer in hydrogen storage systems by improving the thermal behavior of metal hydrides. The thermal conductivity of uncoated and coated powders was measured experimentally. Experiments confirmed that higher operating pressures resulted in improved hydrogen absorption. Not only did enhanced thermal conductivity accelerate hydrogen absorption, but it also reduced local temperature spikes, promoting a more uniform temperature distribution throughout the reactor. These values were then used in a three-dimensional model to simulate the hydrogen absorption process. This model assessed the storage capacity of hydrogen and the temperature distribution over time at various operating pressures (3, 6, 9, 10, 12, and 15 bar). Using heat pipes and fins significantly enhanced heat transfer within the reactor, resulting in improved overall performance.
- 20 February 2026
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- No. Advanced O,p. 1
Enhancing the Hydrogen Storage Performance of LaNi5 Metal Hydrides via Cu, Cu/Ag and Ag Coatings with Improved Thermal Conductivity
This study investigates the thermal and mass transfer behaviors of the LaNi5 alloy during hydrogen absorption after applying three different surface coatings. To enhance heat transfer within the metal hydride reactor and evaluate its performance, three reactor designs were developed: a reference design, a design incorporating a central heat pipe, and an advanced design equipped with a finned heat pipe to improve heat distribution. LaNi5 powders were ground for one hour using mechanical milling and then coated under controlled conditions to produce copper-coated, Cu/Ag double-layer-coated, and silver-coated samples. The findings demonstrate that a homogeneous and stable Cu/Ag duplex coating can be successfully applied to LaNi5 powders. This offers the potential to enhance heat transfer in hydrogen storage systems by improving the thermal behavior of metal hydrides. The thermal conductivity of uncoated and coated powders was measured experimentally. Experiments confirmed that higher operating pressures resulted in improved hydrogen absorption. Not only did enhanced thermal conductivity accelerate hydrogen absorption, but it also reduced local temperature spikes, promoting a more uniform temperature distribution throughout the reactor. These values were then used in a three-dimensional model to simulate the hydrogen absorption process. This model assessed the storage capacity of hydrogen and the temperature distribution over time at various operating pressures (3, 6, 9, 10, 12, and 15 bar). Using heat pipes and fins significantly enhanced heat transfer within the reactor, resulting in improved overall performance.
- 29 December 2025
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 10 (4) , 1373-1382
Surface modification and characterisation of LaNi5 metal hydride powders with Cu and Cu/Ag coatings
The low thermal conductivity of LaNi₅-based metal hydride powders limits efficient heat removal during hydrogen charging and discharging, thereby reducing overall system efficiency. This study examines the application of a Cu/Ag duplex coating on LaNi₅ metal hydride particles to minimize interparticle thermal resistance and improve thermal conductivity. LaNi₅ particles were first ground in a ball mill for one hour, then coated with Cu via a chemical reduction method in a copper sulfate-containing solution. The Cu/Ag duplex coating was subsequently formed by reducing the Cu-coated surfaces with [Ag(NH₃)₂]⁺ complex ions in a solution containing potassium sodium tartrate (KNaC₄H₄O₆·4H₂O). The structural, morphological, and thermal properties of the coatings were characterized using several techniques. Scanning electron microscopy (SEM) was used to analyze the surface morphology, while energy dispersive X-Ray spectroscopy (EDX) confirmed the elemental composition. X-ray diffraction (XRD) was used to determine the phase structure. Differential scanning calorimetry (DSC) was performed to evaluate thermal stability and potential structural transformations. The results show that a uniform and stable Cu/Ag duplex coating can be successfully applied to LaNi5 powders. DSC analysis further reveals that the duplex coating improves the thermal behavior of metal hydrides, offering a promising method for enhancing heat transfer in hydrogen storage systems.
- 29 December 2025
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 10 (4) , 1373-1382
Surface modification and characterisation of LaNi5 metal hydride powders with Cu and Cu/Ag coatings
The low thermal conductivity of LaNi₅-based metal hydride powders limits efficient heat removal during hydrogen charging and discharging, thereby reducing overall system efficiency. This study examines the application of a Cu/Ag duplex coating on LaNi₅ metal hydride particles to minimize interparticle thermal resistance and improve thermal conductivity. LaNi₅ particles were first ground in a ball mill for one hour, then coated with Cu via a chemical reduction method in a copper sulfate-containing solution. The Cu/Ag duplex coating was subsequently formed by reducing the Cu-coated surfaces with [Ag(NH₃)₂]⁺ complex ions in a solution containing potassium sodium tartrate (KNaC₄H₄O₆·4H₂O). The structural, morphological, and thermal properties of the coatings were characterized using several techniques. Scanning electron microscopy (SEM) was used to analyze the surface morphology, while energy dispersive X-Ray spectroscopy (EDX) confirmed the elemental composition. X-ray diffraction (XRD) was used to determine the phase structure. Differential scanning calorimetry (DSC) was performed to evaluate thermal stability and potential structural transformations. The results show that a uniform and stable Cu/Ag duplex coating can be successfully applied to LaNi5 powders. DSC analysis further reveals that the duplex coating improves the thermal behavior of metal hydrides, offering a promising method for enhancing heat transfer in hydrogen storage systems.
- 29 December 2025
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 10 (4) , 1447-1459
Investigation of the effect of coating on hydrogen charge and thermal characteristics in LaNi5 based metal hydrides
The thermal and mass behavior of LaNi5 alloy, a metal hydride-based hydrogen storage material, modified with different surface coating types was investigated during the hydrogen storage process. Based on the experimentally measured thermal conductivity coefficients, four different sample groups were created: Sample 1 – uncoated LaNi5 powder, Sample 2 – copper-coated LaNi5, Sample 3 – copper/silver double-layer-coated LaNi5, and Sample 4 – silver-coated LaNi5. The thermal conductivity values of each sample were determined, and these data were evaluated in a three-dimensional model developed in COMSOL Multiphysics software. During the modeling process, the amount of hydrogen stored in the metal hydride reactor under different operating pressures (4 bar, 8 bar, and 12 bar) was calculated; the transient temperature distribution and hydrogen concentration profiles of the system were analyzed with time. It was shown that the coated samples – especially the Cu, Cu/Ag, and Ag coated samples – had higher thermal conductivities than the uncoated sample. This increase contributes to the shortening of the hydrogen absorption time and the limitation of local temperature increases, resulting in a more homogeneous temperature distribution in the system.
- 29 December 2025
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 10 (4) , 1447-1459
Investigation of the effect of coating on hydrogen charge and thermal characteristics in LaNi5 based metal hydrides
The thermal and mass behavior of LaNi5 alloy, a metal hydride-based hydrogen storage material, modified with different surface coating types was investigated during the hydrogen storage process. Based on the experimentally measured thermal conductivity coefficients, four different sample groups were created: Sample 1 – uncoated LaNi5 powder, Sample 2 – copper-coated LaNi5, Sample 3 – copper/silver double-layer-coated LaNi5, and Sample 4 – silver-coated LaNi5. The thermal conductivity values of each sample were determined, and these data were evaluated in a three-dimensional model developed in COMSOL Multiphysics software. During the modeling process, the amount of hydrogen stored in the metal hydride reactor under different operating pressures (4 bar, 8 bar, and 12 bar) was calculated; the transient temperature distribution and hydrogen concentration profiles of the system were analyzed with time. It was shown that the coated samples – especially the Cu, Cu/Ag, and Ag coated samples – had higher thermal conductivities than the uncoated sample. This increase contributes to the shortening of the hydrogen absorption time and the limitation of local temperature increases, resulting in a more homogeneous temperature distribution in the system.