Arinze Everest Chinweze
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arinze Everest Chinweze has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Augustine Uzodinma Madumere
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication Johannes Buhl
1 shared publication- John Chikaelo Okeke
Nnamdi Azikiwe University Faculty of Engineering
1 shared publication - Mmesoma Echezonachukwu Echeta
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication - Obiora Nnaemeka Ezenwa
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication - Okoye Chibuzor Ndubuisi
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication
Latest Publications
- Open Access
- 27 May 2026
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 26 (2) , 38-47
Effects of Nozzle Diameter and Duty Cycle on Droplet Formation in Drop-On-Demand Additive Manufacturing
Liquid metal drop-on-demand (DOD) additive manufacturing enables precise control of individual droplet deposition. A critical bottleneck in this manufacturing process is achieving continuous, uniform droplet ejection, which is influenced by several parameters, including nozzle diameter and pressure-pulse actuation mechanism. To address this challenge, this study investigated droplet formation using the Volume of Fluid (VOF) method, as it conserves liquid volume, incorporates free surface tracking and interface evolution during droplet formation. The effects of nozzle diameter and duty cycle on droplet size, detachment time, detachment distance, ligament stability and satellite formation were investigated. The results revealed that the droplet diameter scales linearly with nozzle diameter. The gas pressure required for single droplet ejection decreased with increasing nozzle diameter, while the resulting droplet velocity also decreased. The DOE revealed different flow regimes. Droplets with diameters between 0.55 mm and 0.95 mm were produced at 100 Hz, as the duty cycle was varied from 10% to 50% for a 0.3 mm diameter nozzle. Higher duty cycles resulted in larger droplet diameters, droplet overlap and formation of satellite droplets, which led to unstable ejections. Parameter sets were identified for efficient droplet generation, which provide preliminary insights into nozzle diameter and pressure-pulse design for DOD metal additive manufacturing.
- 27 May 2026
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- Vol. 26 (2) , 38-47
Open AccessEffects of Nozzle Diameter and Duty Cycle on Droplet Formation in Drop-On-Demand Additive Manufacturing
Liquid metal drop-on-demand (DOD) additive manufacturing enables precise control of individual droplet deposition. A critical bottleneck in this manufacturing process is achieving continuous, uniform droplet ejection, which is influenced by several parameters, including nozzle diameter and pressure-pulse actuation mechanism. To address this challenge, this study investigated droplet formation using the Volume of Fluid (VOF) method, as it conserves liquid volume, incorporates free surface tracking and interface evolution during droplet formation. The effects of nozzle diameter and duty cycle on droplet size, detachment time, detachment distance, ligament stability and satellite formation were investigated. The results revealed that the droplet diameter scales linearly with nozzle diameter. The gas pressure required for single droplet ejection decreased with increasing nozzle diameter, while the resulting droplet velocity also decreased. The DOE revealed different flow regimes. Droplets with diameters between 0.55 mm and 0.95 mm were produced at 100 Hz, as the duty cycle was varied from 10% to 50% for a 0.3 mm diameter nozzle. Higher duty cycles resulted in larger droplet diameters, droplet overlap and formation of satellite droplets, which led to unstable ejections. Parameter sets were identified for efficient droplet generation, which provide preliminary insights into nozzle diameter and pressure-pulse design for DOD metal additive manufacturing.
- Open Access
- 29 August 2025
- Published by Conscientia Beam in International Journal of Sustainable Energy and Environmental Research
- Vol. 14 (2) , 120-132
Development and performance assessment of post-combustion emission control device, embedded with breadfruit pulp biochar
This study presents the design, fabrication, and experimental evaluation of a small-scale carbon capture device aimed at mitigating exhaust emissions from petrol generators. Motivated by Nigeria’s heavy dependence on fossil fuels and the associated greenhouse gas (GHG) emissions, the research explores the use of breadfruit pulp–derived biochar as a low-cost, sustainable adsorbent for post-combustion carbon dioxide (CO2) capture. The carbon capture system was developed using stainless-steel chambers arranged in series, each packed with graded biochar particles to enhance gas–adsorbent contact. Theoretical design analyses and SolidWorks static simulations were performed to verify the structural adequacy under combined thermal (600 °C) and pressure (7 kPa) loads. Experimental results using an air quality detector showed significant reductions in CO and CO2 emissions, demonstrating the biochar’s adsorption efficiency. Simulation outcomes indicated minimal deformation and confirmed the mechanical stability of the capture unit, although localized stress concentrations suggested a need for minor design improvements. Overall, the study validates the feasibility of using agricultural waste–derived carbon materials for emission control, offering a sustainable solution for small-scale power sources in developing regions.
- 29 August 2025
- Published by Conscientia Beam in International Journal of Sustainable Energy and Environmental Research
- Vol. 14 (2) , 120-132
Open AccessDevelopment and performance assessment of post-combustion emission control device, embedded with breadfruit pulp biochar
This study presents the design, fabrication, and experimental evaluation of a small-scale carbon capture device aimed at mitigating exhaust emissions from petrol generators. Motivated by Nigeria’s heavy dependence on fossil fuels and the associated greenhouse gas (GHG) emissions, the research explores the use of breadfruit pulp–derived biochar as a low-cost, sustainable adsorbent for post-combustion carbon dioxide (CO2) capture. The carbon capture system was developed using stainless-steel chambers arranged in series, each packed with graded biochar particles to enhance gas–adsorbent contact. Theoretical design analyses and SolidWorks static simulations were performed to verify the structural adequacy under combined thermal (600 °C) and pressure (7 kPa) loads. Experimental results using an air quality detector showed significant reductions in CO and CO2 emissions, demonstrating the biochar’s adsorption efficiency. Simulation outcomes indicated minimal deformation and confirmed the mechanical stability of the capture unit, although localized stress concentrations suggested a need for minor design improvements. Overall, the study validates the feasibility of using agricultural waste–derived carbon materials for emission control, offering a sustainable solution for small-scale power sources in developing regions.