A. Klishch
Research Subjects
A. Klishch has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Ju. Sherenkovskyi
2 shared publicationsN. Meranova
2 shared publications- Natalia Mikhailivna Fialko
Institute of Engineering Thermophysics
2 shared publications S. Aloshko
2 shared publicationsD. Gladkov
1 shared publication- O. Martiuk1 shared publication
Latest Publications
- 4 November 2025
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 50 (4) , 96-104
COMPARATIVE ANALYSIS OF FLOW PATTERNS UNDER ISOTHERMAL CONDITIONS AND COMBUSTION IN MICRO-JET BURNERS WITH MULTI-ROW FUEL SUPPLY
The article presents the results of a comparative analysis of isothermal and nonisothermal flow characteristics in stabilizer-type burners with three-row fuel feed, designed for operation at variable excess air ratios. CFD modeling using the FLUENT software package was used as the research method. Simulation experiments were performed using the DDES approach with the Realizable k-є turbulence model. The modeling results revealed significant differences in the flow patterns for the compared situations. These differences include, in particular, the location of high-velocity zones in different regions of the channel. It is shown that the velocity behind the flame stabilizers is generally significantly higher during combustion due to flow acceleration caused by thermal expansion of the gases. This acceleration is found to begin downstream, the farther the gas supply openings are from the stall edge. Particular attention is paid to comparing the characteristics of recirculation zones in the aft region of flame stabilizers, which are responsible for stabilizing the combustion process, for isothermal and nonisothermal flow conditions. It is shown that the extent of these zones increases during combustion, while the maximum absolute velocity values within them decrease. Results are also presented for comparing velocity pulsation fields in the burner devices under study for reacting flows and isothermal flow. It is established that the level of these pulsations during combustion generally significantly exceeds the corresponding level for isothermal flow. The results of these studies can be widely used in selecting the design and operating parameters of the proposed burners.
- 4 November 2025
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 50 (4) , 96-104
COMPARATIVE ANALYSIS OF FLOW PATTERNS UNDER ISOTHERMAL CONDITIONS AND COMBUSTION IN MICRO-JET BURNERS WITH MULTI-ROW FUEL SUPPLY
The article presents the results of a comparative analysis of isothermal and nonisothermal flow characteristics in stabilizer-type burners with three-row fuel feed, designed for operation at variable excess air ratios. CFD modeling using the FLUENT software package was used as the research method. Simulation experiments were performed using the DDES approach with the Realizable k-є turbulence model. The modeling results revealed significant differences in the flow patterns for the compared situations. These differences include, in particular, the location of high-velocity zones in different regions of the channel. It is shown that the velocity behind the flame stabilizers is generally significantly higher during combustion due to flow acceleration caused by thermal expansion of the gases. This acceleration is found to begin downstream, the farther the gas supply openings are from the stall edge. Particular attention is paid to comparing the characteristics of recirculation zones in the aft region of flame stabilizers, which are responsible for stabilizing the combustion process, for isothermal and nonisothermal flow conditions. It is shown that the extent of these zones increases during combustion, while the maximum absolute velocity values within them decrease. Results are also presented for comparing velocity pulsation fields in the burner devices under study for reacting flows and isothermal flow. It is established that the level of these pulsations during combustion generally significantly exceeds the corresponding level for isothermal flow. The results of these studies can be widely used in selecting the design and operating parameters of the proposed burners.
- 30 September 2025
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 49 (3) , 83-93
FLOW STRUCTURE DURING COMBUSTION OF NATURAL GAS IN BURNERS WITH A THREE-ROW FUEL SUPPLY SYSTEM
The objective of the work is to establish the regularities of the flow of a single gas in micro-jet burner devices with a three-row fuel supply system. The burner devices under consideration are intended for operation under conditions of variable values of the total excess air coefficient, 1.1 ... 1.5. The objective of the study was to determine the effects of the influence of the row number of gas supply holes on various characteristics of the non-isothermal flow in the proposed burners. CFD modeling based on the DES approach was used as a research method. Based on the results of the comparative analysis of the flow characteristics when feeding fuel gas to different rows of gas supply holes, it is shown that these characteristics can significantly depend on the row number of the fuel supply. It was found that with an increase in the row number, the indicators of the recirculation zone behind the flame stabilizer change significantly. The levels of flow rates, velocity pulsations, etc. The research results can be used in the design of micro-flare burners of the stabilizer type.
- 30 September 2025
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 49 (3) , 83-93
FLOW STRUCTURE DURING COMBUSTION OF NATURAL GAS IN BURNERS WITH A THREE-ROW FUEL SUPPLY SYSTEM
The objective of the work is to establish the regularities of the flow of a single gas in micro-jet burner devices with a three-row fuel supply system. The burner devices under consideration are intended for operation under conditions of variable values of the total excess air coefficient, 1.1 ... 1.5. The objective of the study was to determine the effects of the influence of the row number of gas supply holes on various characteristics of the non-isothermal flow in the proposed burners. CFD modeling based on the DES approach was used as a research method. Based on the results of the comparative analysis of the flow characteristics when feeding fuel gas to different rows of gas supply holes, it is shown that these characteristics can significantly depend on the row number of the fuel supply. It was found that with an increase in the row number, the indicators of the recirculation zone behind the flame stabilizer change significantly. The levels of flow rates, velocity pulsations, etc. The research results can be used in the design of micro-flare burners of the stabilizer type.