Chun-Bin Yu
Chun-Bin Yu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Fawas. O. Matanmi
Department of Bridge Engineering, Tongji University, 1239 Siping Road, Shanghai 200092, China
1 shared publication - Heqing Tan
College of Civil and Transportation Engineering, Hohai University
1 shared publication - Li-Tao Yu
Tongxiang Transportation Construction Investment Group Co., Ltd., Jiaxing 314500, China
1 shared publication - Muqing Du
College of Civil and Transportation Engineering
1 shared publication - Zhiping Lin
Fujian Expressway Group Co., Ltd., Fuzhou 350001, China
1 shared publication
Latest Publications
- Open Access
- 19 May 2026
- Published by MDPI AG in Infrastructures
- Vol. 11 (5) , 178
Crack Width Calculation Method for Concrete in Hogging Moment Region of Steel–UHPC–NC Composite Girder with Integrated Piers
The application of ultra-high performance concrete (UHPC) in the hogging moment region significantly enhances the crack resistance of concrete slabs of composite girders with integrated piers, while also providing economic benefits. To investigate the crack resistance performance and develop a calculation method for crack width in hogging moment region of steel–UHPC–normal concrete (NC) composite girders, a full-scale bending test was conducted. Based on the test results, the post-cracking residual tensile strength of UHPC was determined according to the energy equivalence principle. A calculation method for reinforcement stress incorporating the tensile contribution of UHPC at a cracked section was proposed and then the applicability for current design codes for crack width calculation was evaluated. For the UHPC–NC interface, a corresponding crack width calculation method was developed. The results indicate that cracks initiated on the surface of the NC layer beneath the UHPC overlay at the cantilever root. Then cracks developed in sequence at the top surface of the UHPC layer cantilever root, the UHPC–NC interface, and the mid-plane of the girder-to-pier joint. Ultimately, UHPC cracks exhibited a “numerous and closely spaced” distribution, whereas NC cracks were “few and widely spaced.” When the residual tensile strength of UHPC at cracked section was considered, the mean value and average coefficient of variation in the ratios of calculated to measured reinforcement stresses for different sections were 1.07 and 0.10, respectively, which can be further used for crack width calculation. The mean ratios of code-predicted to measured UHPC crack widths for different sections using the Chinese code, French code, and European code were 1.10, 0.98, and 1.13, respectively, with corresponding average coefficients of variation of 0.25, 0.33, and 0.28; the Chinese code is recommended for UHPC crack width prediction. For the UHPC–NC interface, an expression for crack width calculation was derived using the comprehensive theory, and the mean ratio of calculated to measured values and the coefficient of variation were 1.08 and 0.18, respectively, demonstrating good predictive accuracy.
- 19 May 2026
- Published by MDPI AG in Infrastructures
- Vol. 11 (5) , 178
Open AccessCrack Width Calculation Method for Concrete in Hogging Moment Region of Steel–UHPC–NC Composite Girder with Integrated Piers
The application of ultra-high performance concrete (UHPC) in the hogging moment region significantly enhances the crack resistance of concrete slabs of composite girders with integrated piers, while also providing economic benefits. To investigate the crack resistance performance and develop a calculation method for crack width in hogging moment region of steel–UHPC–normal concrete (NC) composite girders, a full-scale bending test was conducted. Based on the test results, the post-cracking residual tensile strength of UHPC was determined according to the energy equivalence principle. A calculation method for reinforcement stress incorporating the tensile contribution of UHPC at a cracked section was proposed and then the applicability for current design codes for crack width calculation was evaluated. For the UHPC–NC interface, a corresponding crack width calculation method was developed. The results indicate that cracks initiated on the surface of the NC layer beneath the UHPC overlay at the cantilever root. Then cracks developed in sequence at the top surface of the UHPC layer cantilever root, the UHPC–NC interface, and the mid-plane of the girder-to-pier joint. Ultimately, UHPC cracks exhibited a “numerous and closely spaced” distribution, whereas NC cracks were “few and widely spaced.” When the residual tensile strength of UHPC at cracked section was considered, the mean value and average coefficient of variation in the ratios of calculated to measured reinforcement stresses for different sections were 1.07 and 0.10, respectively, which can be further used for crack width calculation. The mean ratios of code-predicted to measured UHPC crack widths for different sections using the Chinese code, French code, and European code were 1.10, 0.98, and 1.13, respectively, with corresponding average coefficients of variation of 0.25, 0.33, and 0.28; the Chinese code is recommended for UHPC crack width prediction. For the UHPC–NC interface, an expression for crack width calculation was derived using the comprehensive theory, and the mean ratio of calculated to measured values and the coefficient of variation were 1.08 and 0.18, respectively, demonstrating good predictive accuracy.
- Open Access
- 28 January 2020
- Published by Center for Transportation Studies in Journal of Transport and Land Use
- Vol. 13 (1) , 539-558
A multiple-path gradient projection method for solving the logit-based stochastic user equilibrium model
This paper proposes a path-based algorithm for solving the well-known logit-based stochastic user equilibrium (SUE) problem in transportation planning and management. Based on the gradient projection (GP) method, the new algorithm incorporates a novel multiple-path gradient approach to generate the descent direction in consideration of many paths existing in every single origin-destination (O-D) pair. To apply the path-based algorithm, the SUE problem is reformulated as a variational inequality (VI), and a working path set is predetermined. The numerical experiments are conducted on the Winnipeg network where a large number of paths are provided. The results show the multiple-path gradient projection algorithm outperforms the original GP method. Three different step size strategies, including the fixed step size, self-regulated averaging and self-adaptive Armijo’s strategies, are involved to draw a more general conclusion. Also, the effects of the path number on computational performance are analyzed. The multiple-path gradient projection (MGP) method converges much faster than the GP method when the path set size gets large.
- 28 January 2020
- Published by Center for Transportation Studies in Journal of Transport and Land Use
- Vol. 13 (1) , 539-558
Open AccessA multiple-path gradient projection method for solving the logit-based stochastic user equilibrium model
This paper proposes a path-based algorithm for solving the well-known logit-based stochastic user equilibrium (SUE) problem in transportation planning and management. Based on the gradient projection (GP) method, the new algorithm incorporates a novel multiple-path gradient approach to generate the descent direction in consideration of many paths existing in every single origin-destination (O-D) pair. To apply the path-based algorithm, the SUE problem is reformulated as a variational inequality (VI), and a working path set is predetermined. The numerical experiments are conducted on the Winnipeg network where a large number of paths are provided. The results show the multiple-path gradient projection algorithm outperforms the original GP method. Three different step size strategies, including the fixed step size, self-regulated averaging and self-adaptive Armijo’s strategies, are involved to draw a more general conclusion. Also, the effects of the path number on computational performance are analyzed. The multiple-path gradient projection (MGP) method converges much faster than the GP method when the path set size gets large.