PLPengchang Liang

Pengchang Liang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Pengchang Liang has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization of Mix Proportion and Performance Study of Metakaolin-Slag Geopolymer Mortar Based on Orthogonal Experiment

    by Pengchang Liang, Lianyong Zhu, Ruize Yin, Renfei Gao

    To promote the practical application of metakaolin-slag geopolymer materials in engineering repair, it is essential to clarify the influence of mix proportion parameters on macroscopic properties, given their inherent deficiencies of inferior toughness and volume stability. In this study, a five-factor and four-level orthogonal experimental design was adopted to systematically investigate the effects of slag content, water glass modulus, alkali equivalent, water–binder ratio, and sand–binder ratio on the fluidity, compressive strength, flexural strength, compressive-to-flexural strength ratio (toughness indicator), and drying shrinkage rate (volume stability indicator) of geopolymer mortar. Range analysis and variance analysis were conducted to clarify the primary and secondary order of influencing factors for each performance index, and the optimal mix proportion balancing multiple performance demands was determined. The results indicate that alkali equivalent is the core factor governing compressive and flexural strength, whereas slag content dominates the compressive-to-flexural ratio, fluidity and drying shrinkage. The geopolymer mortar achieves relatively optimal comprehensive performance when the slag content is 20%, the sodium silicate modulus is 1.6, the alkali equivalent is 12%, the water-to-binder ratio is 0.49, and the sand-to-binder ratio is 2:1, and all indicators meet the specification requirements for rigid repair mortar. Combined with SEM-EDS and XRD microstructural analysis, the main products of the metakaolin-slag system are amorphous N-A-S-H gel and C-(A)-S-H gel. Appropriate alkali equivalent and slag content can promote the dissolution of aluminosilicate raw materials and facilitate the formation of both gel products, providing microstructural support for the improvement of macroscopic performance.


  • Open Access

    Multi-Objective Optimization Design of a Metakaolin–Slag-Based Binary Solid Waste Geopolymer Mortar Mix Proportion Using Response Surface Methodology

    by Ruize Yin, Lianyong Zhu, Dawei Cheng, Pengchang Liang, Renfei Gao

    This study focuses on the development of sustainable construction materials via geopolymers synthesized from metakaolin and slag, aiming to identify environmentally friendly alternatives for construction material systems. A metakaolin–slag geopolymer mortar (MK–slag) was prepared using metakaolin and slag as fully solid waste raw materials, with sodium silicate solution and sodium hydroxide acting as composite activators. Initially, single-factor experiments were conducted to determine the optimal ranges for metakaolin–slag content, water/binder ratio, and water glass modulus. Subsequently, response surface methodology was employed to develop regression equations that analyze the main and interaction effects of these variables on the 7-day and 28-day compressive strength and water absorption of the mortar. The optimal mix ratio was then identified. The microstructure and formation mechanisms of MK–slag mortar were studied using scanning electron microscopy (SEM), X-ray diffraction (XRD), and mercury intrusion porosimetry (MIP). The results indicate that all factors follow quadratic polynomial relationships with the response variables, showing a regression coefficient (R2) greater than 0.98, indicating an excellent model fit and prediction accuracy. According to model predictions, the optimal mix parameters under multi-objective optimization were found to be a metakaolin-to-slag ratio of 45%: 55%, a water/binder ratio of 0.45, and a water glass modulus of 1.3. After 28 days of curing, the primary hydration products were gel-like substances such as N-A-S-H and C-A-S-H. These gels interweave and overlap to form a high-density, structurally robust binary solid waste geopolymer mortar. This approach expands the application of solid waste materials, such as metakaolin and slag, while enhancing the recycling and utilization efficiency of these waste products.