Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lianyong Zhu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effects of Nano-SiO2 on the Pore Structure and Crack Behavior of Basalt Fiber-Reinforced Coal Gangue–Slag Geopolymer Concrete

    by Weizi Wang, Lianyong Zhu, Tao Li, Renfei Gao

    To improve the mechanical performance and crack resistance of coal gangue–slag geopolymer concrete, basalt fiber-reinforced geopolymer concrete was prepared using calcined coal gangue powder and slag as composite precursors. The effects of nano-SiO2 dosage on strength, water absorption, and crack evolution under splitting tensile loading were investigated. Digital image correlation (DIC), scanning electron microscopy (SEM), and mercury intrusion porosimetry (MIP) were further employed to characterize the crack evolution and microstructural changes associated with nano-SiO2 incorporation. The results show that the performance of the specimens was strongly dependent on the nano-SiO2 dosage, with the NS0.5 mixture (0.5% nano-SiO2) exhibiting the most pronounced improvement. Compared with the reference mixture, the 28 d compressive strength and splitting tensile strength of NS0.5 reached 86.80 MPa and 6.02 MPa, corresponding to increases of 17.67% and 39.97%, respectively; meanwhile, the 24 h water absorption decreased from 4.78% to 4.25%. The DIC results indicate that 0.5% nano-SiO2 delayed the localization of maximum principal strain and the penetration of the main crack, reducing the peak crack width from 0.487 mm to 0.222 mm, with a reduction of 54.4%. The microstructural results show that an appropriate nano-SiO2 dosage reduced the total porosity from 13.93% to 5.03%, shifted the pore structure from macropore-dominated to fine-pore-dominated, and decreased the proportion of coarse connected pores and crack-like pores. In contrast, the reduced enhancement observed at higher nano-SiO2 dosages may be associated with poorer nanoparticle dispersion and increased local heterogeneity, although particle agglomeration was not directly verified in this study. Overall, the improvements obtained with 0.5% nano-SiO2 are directly consistent with matrix densification and pore-structure refinement. Micro-filling, heterogeneous nucleation, and additional gel formation are proposed as plausible contributing mechanisms rather than directly verified processes.

  • Open Access

    Mechanical Properties of Basalt-Fiber-Reinforced Metakaolin–Slag–Fly Ash Geopolymer Mortar Characterized by 2D-DIC

    by Renfei Gao, Lianyong Zhu, Pengchang Liang, Weizi Wang, Ruize Yin

    Against the backdrop of rapid development in low-carbon building materials, geopolymer mortar has become a high-quality alternative to traditional cement-based materials due to its advantages of environmental friendliness, high strength, and excellent durability. However, its inherent brittleness and tendency to crack severely limit its widespread adoption and use in engineering. To mitigate the inherent brittleness of geopolymer mortar, this study developed a ternary binder system composed of metakaolin, slag, and fly ash. The effects of basalt fiber contents of 0%, 0.25%, 0.50%, 0.75%, 1.00%, and 1.25% by mass on the flowability, flexural strength, compressive strength, and deformation behavior of the geopolymer mortar were systematically investigated. The evolution of the displacement and strain fields during flexural and compressive loading was monitored in real time using two-dimensional digital image correlation (2D-DIC). The fiber-reinforcement mechanism was further examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR). The results show that basalt fiber reduces mortar flowability, and the reduction becomes more pronounced with increasing fiber content. The flexural strength first increased and then decreased with increasing fiber content; at 0.50% fiber content, the 28-day flexural strength reached 12.6 MPa, which was 8.2% higher than that of the fiber-free control. The compressive strength increased only slightly at a low fiber content of 0.25% and then decreased when the fiber content exceeded 0.50%. The 2D-DIC results indicate that a moderate fiber content (0.50–0.75%) markedly increased the ultimate displacement, delayed crack propagation, and enhanced the post-cracking deformation capacity. Microstructural observations revealed that an appropriate fiber content promoted good interfacial bonding with the matrix and enabled fiber bridging and crack resistance. In contrast, excessive fiber addition caused agglomeration-induced micropores and microcracks, thereby degrading mechanical properties. Overall, the recommended basalt fiber content is 0.25–0.50%. These findings provide a theoretical and experimental basis for optimizing high-performance, low-carbon geopolymer mortar for engineering applications.


  • Open Access

    Optimization of Mix Proportion and Performance Study of Metakaolin-Slag Geopolymer Mortar Based on Orthogonal Experiment

    by Pengchang Liang, Lianyong Zhu, Ruize Yin, Renfei Gao

    To promote the practical application of metakaolin-slag geopolymer materials in engineering repair, it is essential to clarify the influence of mix proportion parameters on macroscopic properties, given their inherent deficiencies of inferior toughness and volume stability. In this study, a five-factor and four-level orthogonal experimental design was adopted to systematically investigate the effects of slag content, water glass modulus, alkali equivalent, water–binder ratio, and sand–binder ratio on the fluidity, compressive strength, flexural strength, compressive-to-flexural strength ratio (toughness indicator), and drying shrinkage rate (volume stability indicator) of geopolymer mortar. Range analysis and variance analysis were conducted to clarify the primary and secondary order of influencing factors for each performance index, and the optimal mix proportion balancing multiple performance demands was determined. The results indicate that alkali equivalent is the core factor governing compressive and flexural strength, whereas slag content dominates the compressive-to-flexural ratio, fluidity and drying shrinkage. The geopolymer mortar achieves relatively optimal comprehensive performance when the slag content is 20%, the sodium silicate modulus is 1.6, the alkali equivalent is 12%, the water-to-binder ratio is 0.49, and the sand-to-binder ratio is 2:1, and all indicators meet the specification requirements for rigid repair mortar. Combined with SEM-EDS and XRD microstructural analysis, the main products of the metakaolin-slag system are amorphous N-A-S-H gel and C-(A)-S-H gel. Appropriate alkali equivalent and slag content can promote the dissolution of aluminosilicate raw materials and facilitate the formation of both gel products, providing microstructural support for the improvement of macroscopic performance.


  • Open Access

    Research on Mechanical Properties and Crack Evolution of Basalt Fiber-Reinforced Coal Gangue–Slag Geopolymer Concrete Based on Digital Image Correlation

    by Weizi Wang, Lianyong Zhu, Jingcheng Ju, Xiaotong Gao, Xi Chen

    To investigate the influence of basalt fiber (BF) on the mechanical properties and crack evolution of coal gangue–slag geopolymer concrete, geopolymer concrete specimens were prepared using coal gangue powder calcined at 700 °C and slag as precursors, with BF contents ranging from 0 to 1.25%. Mechanical testing combined with digital image correlation (DIC), scanning electron microscopy (SEM), and X-ray diffraction (XRD) was conducted to evaluate the effects of BF on macroscopic mechanical behavior, crack evolution, and underlying microstructural mechanisms. The results demonstrate that BF effectively enhances both the mechanical performance and crack-control capacity of coal gangue–slag geopolymer concrete, exhibiting a clear content-dependent trend. Compressive strength initially increases and subsequently decreases with increasing BF content. The 28-day compressive strength reaches a maximum value of 84.05 MPa at a BF content of 0.5%, representing an 11.92% improvement compared with the control group. Splitting tensile strength and flexural strength attain their peak values at a BF content of 1%, increasing by 37.88% and 25.81%, respectively. DIC analysis indicates that BF delays strain localization and effectively restrains the propagation of dominant cracks. Specifically, the compressive strain field becomes more uniformly distributed at 0.5% BF content, while crack propagation during splitting failure is more stable at 1% BF content. SEM observations reveal that the primary strengthening mechanisms include crack bridging, interfacial load transfer, and energy dissipation associated with fiber pull-out. XRD analysis shows that BF incorporation does not significantly alter the phase composition of the coal gangue–slag geopolymer system; thus, performance enhancement mainly arises from fiber bridging and interfacial reinforcement rather than changes in primary reaction products.


  • Open Access

    Multi-Objective Optimization Design of a Metakaolin–Slag-Based Binary Solid Waste Geopolymer Mortar Mix Proportion Using Response Surface Methodology

    by Ruize Yin, Lianyong Zhu, Dawei Cheng, Pengchang Liang, Renfei Gao

    This study focuses on the development of sustainable construction materials via geopolymers synthesized from metakaolin and slag, aiming to identify environmentally friendly alternatives for construction material systems. A metakaolin–slag geopolymer mortar (MK–slag) was prepared using metakaolin and slag as fully solid waste raw materials, with sodium silicate solution and sodium hydroxide acting as composite activators. Initially, single-factor experiments were conducted to determine the optimal ranges for metakaolin–slag content, water/binder ratio, and water glass modulus. Subsequently, response surface methodology was employed to develop regression equations that analyze the main and interaction effects of these variables on the 7-day and 28-day compressive strength and water absorption of the mortar. The optimal mix ratio was then identified. The microstructure and formation mechanisms of MK–slag mortar were studied using scanning electron microscopy (SEM), X-ray diffraction (XRD), and mercury intrusion porosimetry (MIP). The results indicate that all factors follow quadratic polynomial relationships with the response variables, showing a regression coefficient (R2) greater than 0.98, indicating an excellent model fit and prediction accuracy. According to model predictions, the optimal mix parameters under multi-objective optimization were found to be a metakaolin-to-slag ratio of 45%: 55%, a water/binder ratio of 0.45, and a water glass modulus of 1.3. After 28 days of curing, the primary hydration products were gel-like substances such as N-A-S-H and C-A-S-H. These gels interweave and overlap to form a high-density, structurally robust binary solid waste geopolymer mortar. This approach expands the application of solid waste materials, such as metakaolin and slag, while enhancing the recycling and utilization efficiency of these waste products.


  • Open Access

    Intermittent Drip Irrigation Soil Wet Front Prediction Model and Effective Water Storage Analysis

    by Zhu Zhu, Muhammad Waseem Rasheed, Muhammad Safdar, Baolin Yao, Hudan Tumaerbai, Abid Sarwar, Lianyong Zhu

    The depth and width of drip infiltration play a critical role in designing effective irrigation strategies. However, existing models primarily focus on continuous irrigation and fail to predict wetting patterns under intermittent drip irrigation. This study developed an infiltration model to estimate soil moisture depth and width under intermittent drip irrigation and identified strategies that enhance effective water storage. Indoor soil box simulations were conducted, with continuous drip irrigation as the control. Results showed that intermittent irrigation increased infiltration width and reduced depth, maximizing water storage efficiency. We recommend adopting an intermittent irrigation system with 1.5 h of irrigation followed by a 0.5 h interval, repeated four times. This system increased effective water storage by up to 16.23% compared to continuous irrigation. The proposed method is suitable for sandy loam farmland in southern Xinjiang and can significantly improve water use efficiency in arid regions.