E. M. Zapolskaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
E. M. Zapolskaya has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Irina Alekseevna Panchenko
Siberian State Industrial University
2 shared publications - Sergey V. Konovalov
Siberian State Industrial University
2 shared publications - Vladislav K. Drobyshev
Siberian State Industrial University, Novokuznetsk, Russia
2 shared publications A. R. Mikhno
1 shared publication- V. M. Alzhev1 shared publication
Latest Publications
- 7 July 2026
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 6,p. 27-32
Comparison of vacuum induction casting and wire-arc method for obtaining CoCrFeMnNi alloys
This paper presents a comparative study of two manufacturing methods for Co–Cr–Fe–Mn–Ni high-entropy alloys: vacuum induction casting and wire-arc cladding. The microstructure of the as-cast alloy specimens is entirely face-centered cubic (FCC), exhibiting dendritic segregation with the enrichment of interdendritic regions with nickel and manganese. The maximum microhardness reaches 155 HV at a content of 30 at.% Mn and 10 at.% Fe; however, the wear rate under these conditions is 8.81×10-5 mm3/(N·m). Compositional optimization to Co20Cr20Fe30Mn10Ni20 allows for reducing the wear rate to 2.09×10-5 mm3/(N·m), which is 4.2 times less than that of the manganese-enriched counterpart. The microstructure of the alloy produced by wire-arc cladding is characterized by a pronounced structural heterogeneity resulting from rapid crystallization and the diffusion of iron from the substrate. Despite a microhardness variation ranging from 151 to 181 HV, the clad specimens exhibit an ultimate tensile strength of 943 MPa and an elongation of 36.8%, which surpass the performance of their as-cast counterparts. Conversely, in the as-cast state, the microstructure forms under slower cooling conditions, which promotes dendritic segregation and a relatively coarse dispersion of structural constituents, thereby limiting ductility and wear resistance. The obtained results demonstrate that wire-arc cladding is a promising method for the localized formation of wear-resistant functional layers with high strength and toughness, whereas the casting method is suitable for producing bulk blanks with predictable but lower wear resistance. The following optimization strategies are proposed: adjusting the manganese-to-iron ratio and applying heat treatment for the as-cast alloys, and controlling the heat input and core powder composition for the wire-arc coatings to minimize iron dilution.The study was conducted under the State Assignment of the Ministry of Science and Higher Education of the Russian Federation No. 075-00087-2401.
- 7 July 2026
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 6,p. 27-32
Comparison of vacuum induction casting and wire-arc method for obtaining CoCrFeMnNi alloys
This paper presents a comparative study of two manufacturing methods for Co–Cr–Fe–Mn–Ni high-entropy alloys: vacuum induction casting and wire-arc cladding. The microstructure of the as-cast alloy specimens is entirely face-centered cubic (FCC), exhibiting dendritic segregation with the enrichment of interdendritic regions with nickel and manganese. The maximum microhardness reaches 155 HV at a content of 30 at.% Mn and 10 at.% Fe; however, the wear rate under these conditions is 8.81×10-5 mm3/(N·m). Compositional optimization to Co20Cr20Fe30Mn10Ni20 allows for reducing the wear rate to 2.09×10-5 mm3/(N·m), which is 4.2 times less than that of the manganese-enriched counterpart. The microstructure of the alloy produced by wire-arc cladding is characterized by a pronounced structural heterogeneity resulting from rapid crystallization and the diffusion of iron from the substrate. Despite a microhardness variation ranging from 151 to 181 HV, the clad specimens exhibit an ultimate tensile strength of 943 MPa and an elongation of 36.8%, which surpass the performance of their as-cast counterparts. Conversely, in the as-cast state, the microstructure forms under slower cooling conditions, which promotes dendritic segregation and a relatively coarse dispersion of structural constituents, thereby limiting ductility and wear resistance. The obtained results demonstrate that wire-arc cladding is a promising method for the localized formation of wear-resistant functional layers with high strength and toughness, whereas the casting method is suitable for producing bulk blanks with predictable but lower wear resistance. The following optimization strategies are proposed: adjusting the manganese-to-iron ratio and applying heat treatment for the as-cast alloys, and controlling the heat input and core powder composition for the wire-arc coatings to minimize iron dilution.The study was conducted under the State Assignment of the Ministry of Science and Higher Education of the Russian Federation No. 075-00087-2401.
- 21 January 2026
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (12) , 1-11
Structural and mechanical characteristics of high-entropy CoCrFeMnNi alloys manufactured by vacuum induction melting
- 21 January 2026
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (12) , 1-11
Structural and mechanical characteristics of high-entropy CoCrFeMnNi alloys manufactured by vacuum induction melting