VDVladislav K. Drobyshev

Vladislav K. Drobyshev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vladislav K. Drobyshev has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Comparison of vacuum induction casting and wire-arc method for obtaining CoCrFeMnNi alloys

    by S. V. Konovalov, V. K. Drobyshev, I. A. Panchenko, E. M. Zapolskaya, A. R. Mikhno, V. M. Alzhev

    This paper presents a comparative study of two manufacturing methods for Co–Cr–Fe–Mn–Ni high-entropy alloys: vacuum induction casting and wire-arc cladding. The microstructure of the as-cast alloy specimens is entirely face-centered cubic (FCC), exhibiting dendritic segregation with the enrichment of interdendritic regions with nickel and manganese. The maximum microhardness reaches 155 HV at a content of 30 at.% Mn and 10 at.% Fe; however, the wear rate under these conditions is 8.81×10-5 mm3/(N·m). Compositional optimization to Co20Cr20Fe30Mn10Ni20 allows for reducing the wear rate to 2.09×10-5 mm3/(N·m), which is 4.2 times less than that of the manganese-enriched counterpart. The microstructure of the alloy produced by wire-arc cladding is characterized by a pronounced structural heterogeneity resulting from rapid crystallization and the diffusion of iron from the substrate. Despite a microhardness variation ranging from 151 to 181 HV, the clad specimens exhibit an ultimate tensile strength of 943 MPa and an elongation of 36.8%, which surpass the performance of their as-cast counterparts. Conversely, in the as-cast state, the microstructure forms under slower cooling conditions, which promotes dendritic segregation and a relatively coarse dispersion of structural constituents, thereby limiting ductility and wear resistance. The obtained results demonstrate that wire-arc cladding is a promising method for the localized formation of wear-resistant functional layers with high strength and toughness, whereas the casting method is suitable for producing bulk blanks with predictable but lower wear resistance. The following optimization strategies are proposed: adjusting the manganese-to-iron ratio and applying heat treatment for the as-cast alloys, and controlling the heat input and core powder composition for the wire-arc coatings to minimize iron dilution.The study was conducted under the State Assignment of the Ministry of Science and Higher Education of the Russian Federation No. 075-00087-2401.

  • EVOLUTION OF MECHANICAL PROPERTIES OF MEDIUM-ENTROPY ALLOYS OF THE COCRNBMNNI SYSTEM

    by Sergey V. Konovalov, Vladislav K. Drobyshev, Irina A. Panchenko, Sergey V. Vorobyov, Ltd Weihai Liyu Industrial Co., Yu J

    Problem Statement (Relevance). The development of new structural materials with an optimal balance of strength and ductility is one of the key challenges of modern materials science. Medium-entropy alloys of the Co-Cr-Ni system are of considerable interest; however, their properties can be further enhanced through microalloying with elements causing significant atomic lattice distortions, such as niobium and manganese. Understanding the influence of such additives on the structure and mechanical behavior is an important scientific task. Objectives. The research is aimed at investigating the possibility of controlling the mechanical properties of medium-entropy alloys of the Co-Cr-Ni system through controlled alloying with small additions of niobium and manganese (2–6 at.%). Methods Applied. Four alloys of the Nb-Mn-Ni-Co-Cr system have been obtained by vacuum casting followed by remelting for homogenization. Mechanical properties have been studied using uniaxial tensile testing at room temperature, as well as micro- and nanoindentation techniques (according to ISO 14577) to determine hardness and elastic modulus. Fractographic analysis of fracture surfaces has been carried out using scanning electron microscopy. Originality. For the first time, the effect of combined alloying with niobium and manganese on the complex mechanical properties of Co-Cr-Ni-based medium-entropy alloys has been systematically studied. Correlations between elemental composition, hardness, tensile strength, and fracture behavior have been established. Result. It has been found that the addition of niobium leads to solid-solution strengthening due to atomic lattice distortions. The highest values of microhardness (140.7 HV), nanohardness (2.29 GPa), and Young’s modulus (156 GPa) have been obtained for the Nb₂Mn₂Ni₃₆Co₄₀Cr₂₀ composition. The maximum ultimate tensile strength (641 MPa) at relatively low hardness has been demonstrated by the Nb₂Mn₂Ni₃₀Co₄₀Cr₂₆ alloy, indicating a favorable combination of strength and ductility. Fractographic analysis has confirmed a predominantly ductile fracture mechanism. Practical Relevance. The obtained results demonstrate that controlled alloying with niobium and manganese is an effective approach for tailoring the strength-ductility balance in medium-entropy alloys, opening prospects for the development of new structural materials with targeted performance characteristics.

  • Investigation of the Porosity and Surface Properties of AlSi10Mg Alloy Produced by Selective Laser Melting

    by S. V. Konovalov, V. K. Drobyshev, I. A. Panchenko, I. A. Kan, M. O. Gilvitinov

    The surface mechanical properties of AlSi10Mg alloy produced by selective laser melting (SLM) with different laser scan angles α (45°, 67°, 90°) were investigated. Instrumented indentation revealed differences in nanohardness H and elastic modulus E: the α = 90° variant provided the highest nanohardness H = 1.57 ± 0.35 GPa and the lowest maximum indenter penetration depth hmax = 1.2 µm, whereas the α = 67° variant exhibited the highest elastic modulus E = 46.4 ± 3.19 GPa. Scratch testing showed the largest groove depth for the α = 45° sample—8.1 µm, with a friction coefficient μ = 0.79; the smallest groove depth for α = 67°—6.4 µm, μ = 0.73; and intermediate values for α = 90°—6.9 µm, μ = 0.74. Scanning electron microscopy of the hardest sample (α = 90°) revealed surface porosity with predominantly elongated defects: 81% of pores 2, a low fraction of pores <50 µm (18.8%), and isolated large cavities up to 457 µm.

  • Studying the Effect of Electron Beam and Ion Plasma Treatment on the Strength Characteristics of AA7075 Alloy

    by Irina A. Panchenko, Vladislav K. Drobyshev, Dmitry N. Labunskiy, Sergey V. Konovalov

    Problem Statement (Relevance). Aluminum alloys of the 7075 grade have a high strength-to-weight ratio, however, traditional methods of production of these alloys are associated with the risk of defects (micropores, cracks) and heterogeneity of the material properties, which complicate its implementation in the existing technological cycles of metallurgical production. Objectives. The research is aimed at determining the influence of ion-plasma action modes on the mechanical properties (microhardness) on the surface of AA7075 alloy samples. The main objective of the work is to study the influence of optimal parameters of electron-beam and ion-plasma action on the strength characteristics of 7075 aluminum alloy. Methods Applied. Modern research infrastructure facilities are presented as equipment, using the similar electron source in an argon environment. Fatigue life, uniaxial tension, special purity units were used for mechanical tests. Using a Vickers microhardness tester (State standard GOST 9450-76), the microhardness distribution was studied to find the optimal nitriding modes for 9 test samples of AA7075 alloy. Originality. It lies in obtaining new results on the evolution of mechanical properties of materials manufactured by wire-arc additive technologies under energy impact on their surface. Result. The microhardness values and strength properties were determined, on the basis of which conclusions were made on the optimal nitriding modes, the effect of electron-beam and combined treatment on the strength and fatigue life of AA7075 alloy. Practical Relevance. The research results can be used to select the optimal temperature and time modes for the composition nitriding, as well as to develop new materials with improved performance characteristics.

  • Mechanical Properties and Structure of High-Entropy Alloys Сo20Cr20Fe10Mn30Ni20 and Co20Cr20Zr9Mn31Ni20

    by V. K. Drobyshev, S. V. Konovalov, I. A. Panchenko, Xizhang Chen

    The mechanical properties (nanohardness, Young’s modulus, microhardness, wear resistance), microstructure, and phase composition of the high-entropy alloys Сo20Cr20Fe10Mn30Ni20 and Co20Cr20Zr9Mn31Ni20 were investigated. The influence of substituting Zr for Fe on the structural-phase state of the CoCrMnNi system was evaluated. In the Co20Cr20Zr9Mn31Ni20 alloy, intermetallic compounds (e.g., ZrCo2, Cr2Ni3) were observed to form, which may be attributed to the larger atomic radius of Zr (0.160 nm) compared to Co, Cr, Mn, and Ni (~0.125–0.135 nm). This elemental partitioning induces localized lattice strain, promoting elemental segregation and intermetallic formation. The microstructure of the Co20Cr20Fe10Mn30Ni20 and Co20Cr20Zr9Mn31Ni20 alloys was analyzed via scanning electron microscopy (SEM) combined with characteristic X-ray emission mapping. SEM revealed that substituting zirconium for iron in the high-entropy alloy (up to 10 at %) led to the precipitation of secondary zirconium-rich phases, which reduced the chromium content available for dissolution in the matrix. The Co20Cr20Zr9Mn31Ni20 alloy exhibited 159% higher nanohardness and a 30.4% greater Young’s modulus compared to the non-equiatomic Cantor high-entropy alloy (CoCrFeMnNi), indicating superior strength and resistance to elastic deformation. The lower margin of error in the Young’s modulus of the Co20Cr20Fe10Mn30Ni20 alloy may stem from its more homogeneous elemental distribution within the as-cast ingot. Both alloys demonstrated comparable wear resistance parameters, with a wear rate of ≈2.08 × 10–5 g/rev, implying a mass loss of 0.0000208 g per revolution under frictional conditions. This exceptionally low wear rate underscores the need for further investigation into the underlying wear mechanisms.

  • Microstructure and Mechanical Behavior of Co40Cr12Nb2Mn6Ni40 Medium-Entropy Alloy

    by S. V. Konovalov, V. K. Drobyshev, I. A. Panchenko, A. A. Neiman, J. Yu

    The microstructural features and mechanical behavior of a Co40Cr12Nb2Mn6Ni40 medium-entropy alloy fabricated by vacuum-induction melting were studied. The microstructural studies by optical and scanning electron microscopies revealed the formation of a dendritic architecture with a dendrite size of 150–250 µm. Energy-dispersive spectroscopy confirmed a uniform Co/Ni ratio of ≈1 : 1 in the matrix and the homogeneous distribution of chromium and manganese throughout the sample volume. The presence of fine Nb-rich intermetallic particles with a niobium content of up to 6 at %, which provide dispersion strengthening of the material, was established. A comprehensive study of the mechanical behavior was carried out by instrumental indentation under loads ranging from 15 to 1000 mN and by uniaxial tensile tests. Nanoindentation revealed a pronounced dependence of hardness and elastic modulus on the applied load: the hardness decreased from 3.21 ± 0.61 GPa to 1.18 ± 0.6 GPa and the elastic modulus decreased from 131.7 ± 44.1 to 44.7 ± 1.4 GPa. The ultimate tensile strength was 486 MPa, with a high elongation to failure of 92.6%. The specimens were found to exhibit a mixed-mode fracture characterized chiefly by a ductile dimpled mechanism of fracture with the presence of isolated regions of transcrystalline cleavage. The size of dimples varied from 3 to 20 µm, with large dimples (10–20 µm) constituting approximately 20% of the total count. Spherical inclusions of up to 5 µm in size, which served as micropore nucleation sites, were detected at the bottom of the large dimples.

  • Open Access

    STUDY OF HIGH-ENTROPY ALLOYS AND THEIR APPLICATION FIELDS

    by Siberian State Industrial University, Владислав Константинович Дробышев, Sergey V. Konovalov, Ирина Алексеевна Панченко

    ИССЛЕДОВАНИЕ ВЫСОКОЭНТРОПИЙНЫХ СПЛАВОВ И ОБЛАСТЬ ИХ ПРИМЕНЕНИЯ


  • ПОСЛОЙНОЕ ИНСТРУМЕНТАЛЬНОЕ ИДЕНТИРОВАНИЕ СПЛАВА AA7075, ПОЛУЧЕННОГО МЕТОДОМ АДДИТИВНЫХ ТЕХНОЛОГИЙ

    by И.а. Панченко, В.к. Дробышев, С.в. Коновалов, М.м. Баженова, Д.н. Лабунский

    Алюминиевые сплавы широко применяются в различных отраслях промышленности, включая авиацию, электронику, автомобильную и военную промышленность. Нанотвердость и модуль Юнга алюминиевых сплавов играют значимую роль в их исследовании и оптимизации, так как результаты измерения предоставляют более точную информацию о механических свойствах материалов на наноуровне, что особенно актуально при разработке новых деталей и улучшении характеристик имеющихся сплавов. Изучение нанотвердости алюминиевого сплава 7075 позволяет исследовать воздействие различных добавок и легирующих компонентов на их механические качества. Полученные данные используются для оптимизации режимов получения сплавов, методом аддитивного производства и формирования новых материалов с усовершенствованными свойствами. Использование методов инструментального индентирования позволило установить присутствие в верхней области фаз, влияющих за нанотвердость детали. Образование вторичных фаз, имеющих плохую растворимость в металлической матрице, обусловлено более высоким градиентом температур, за счет межслоевого охлаждения. Вторичные фазы затрудняют движение границ зерен, что способствует увеличению нанотвердости и модуля упругости до 2,3±3,27 ГПа и 100,1±0,6 ГПа соответственно. Методами СЭМ установлено, что в слоях рядом с подложкой, где скорость охлаждения детали становится меньше с увеличением высоты наплавленного образца, средний размер зерна составляет от 10 до 15 мкм, а в областях с более высоким температурным градиентом за счет межслоевого охлаждения размер зерен уменьшается до 5-10 мкм.

  • Open Access

    Structure and mechanical properties of high-entropy alloys of the CoCrZrMnNi system with different Zr and Mn contents produced by vacuum-induction melting

    by Siberian State Industrial University, Sergey V. Konovalov, Vladislav K. Drobyshev, Irina A. Panchenko, Haixin Li, Ли Хайсинь

    The mechanical properties and microstructure of high-entropy alloys (HEA) of the CoCrZrMnNi system produced by vacuum-induction melting are studied depending on the change in the Zr and Mn content. The effect of the Zr and Mn percentage on the microstructure and mechanical properties (Young’s modulus, nanohardness, microhardness) of the high-entropy alloys of the CoCrZrMnNi system is estimated. The relationship between varying the percentage of Zr and Mn and changing the grain size and mechanical properties of high-entropy alloys is studied. The structure, chemical composition and distribution of the intensity of characteristic X-ray radiation of atoms are studied using scanning electron microscopy. The study by scanning electron microscopy methods has demonstrated that in CoCrZrMnNi alloys, with an increase in the zirconium content and a decrease in the manganese content closer to the equiatomic composition, the material structure became more homogeneous. Changing the percentage of zirconium from 8 to 28 at. % contributed to the grain size reduction from 30 to 5 μm and a more uniform elemental distribution. The Сo19.8Cr17.5Zr15.3Mn27.7Ni19.7 alloy demonstrated the highest nanohardness (10 GPa) and Young’s modulus (161 GPa) during instrumental indentation with an indenter load of 50 mN. The Сo20.4Cr18.0Zr7.9Mn33.3Ni20.3 alloy has the lowest nanohardness, Young’s modulus, and microhardness among other alloys, which may be related to the coarse-grained structure with a grain size of up to 30 μm. As the indenter load increased to 5 N, the microhardness of the Сo19.8Cr17.5Zr15.3Mn27.7Ni19.7 alloy decreased compared to the Сo18.7Cr16.5Zr28.9Mn17.4Ni18.6 alloy, which may indicate more universal mechanical properties of alloys with equiatomic zirconium content.