Norbert Pirch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Norbert Pirch has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Andres Gasser
Fraunhofer ILT - Institute for Laser Technology
1 shared publication- Bohang Gao1 shared publication
- Chongliang Zhong
Fraunhofer ILT - Institute for Laser Technology
1 shared publication Constantin Leon Häfner
1 shared publication- Eduard Weisser
Department of DED Coating and Heat Treatment, Fraunhofer Institute for Laser Technology ILT 1 , Aachen, North Rhine-Westphalia 52074
1 shared publication - Gandham Phanikumar
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, Chennai, India
1 shared publication
Latest Publications
- Open Access
- 16 March 2026
- Published by Elsevier in SSRN Electronic Journal
In-situ camera-based condition monitoring for wear classification and quantification on scanner protective windows in laser powder bed fusion (PBF-LB/M)
This work presents a camera-based condition monitoring system for scanner protective windows (SPWs) in laser powder bed fusion of metals (PBF-LB/M). Methods for classification of dust and fiber particles of an area equivalent diameter above 0.030 mm, scorch marks, and metal condensate contamination are described. To quantify the effect of metal condensate contamination on relevant laser beam parameters and correlate it with SPW condition monitoring images, the transmissivity of worn SPWs, wear-induced changes in measured beam caustics, and transient thermally-induced effects on the power density distribution are investigated. In this work, SPW wear results in a transmissivity loss of up to 5.66 % and a peak intensity reduction of up to 56.4 %. Moreover, even moderate condensate coverage induces transient focus shifts lasting up to 17 s. In experiments with a dynamically deflected laser beam, the focus position shifts by up to 8.3 mm within only 1 s of exposure. Based on these measurements, SPW images are labeled and a critical metal condensate coverage is derived as an alert criterion. The proposed condition monitoring system thereby enables in-situ quantification of SPW wear progression during ongoing PBF-LB/M processes.
- 16 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIn-situ camera-based condition monitoring for wear classification and quantification on scanner protective windows in laser powder bed fusion (PBF-LB/M)
This work presents a camera-based condition monitoring system for scanner protective windows (SPWs) in laser powder bed fusion of metals (PBF-LB/M). Methods for classification of dust and fiber particles of an area equivalent diameter above 0.030 mm, scorch marks, and metal condensate contamination are described. To quantify the effect of metal condensate contamination on relevant laser beam parameters and correlate it with SPW condition monitoring images, the transmissivity of worn SPWs, wear-induced changes in measured beam caustics, and transient thermally-induced effects on the power density distribution are investigated. In this work, SPW wear results in a transmissivity loss of up to 5.66 % and a peak intensity reduction of up to 56.4 %. Moreover, even moderate condensate coverage induces transient focus shifts lasting up to 17 s. In experiments with a dynamically deflected laser beam, the focus position shifts by up to 8.3 mm within only 1 s of exposure. Based on these measurements, SPW images are labeled and a critical metal condensate coverage is derived as an alert criterion. The proposed condition monitoring system thereby enables in-situ quantification of SPW wear progression during ongoing PBF-LB/M processes.
- Open Access
- 9 February 2026
- Published by Elsevier in SSRN Electronic Journal
Process parameter influences on 17-4PH martensitic stainless-steel coatings produced by extreme high-speed laser cladding (EHLA)
Achieving high-performance coatings in the as-built condition, without the need for subsequent heat treatment, is an important and increasingly relevant objective in metallic materials manufacturing, particularly for protective metallic coatings. In this study, defect-free 17-4PH stainless-steel coatings were fabricated using Extreme High-Speed Laser Cladding (EHLA). By tailoring the laser processing parameters, nearly fully martensitic microstructures were obtained in the as-built state. Detailed analysis revealed two distinct dilution mechanisms: diffusion-controlled bonding at the coating–substrate interface and convection- induced dilution of chromium within the coating interior, which the latter is of critical importance to the corrosion resistance of stainless-steel coatings. Furthermore, phase transformation kinetics were simulated using the temperature histories derived from process modeling. The results indicate that the thermal cycles experienced by tracks whose peak temperatures fall within the austenite stability range play a critical role in determining the final phase constitution of the coating. Together, these findings provide key insights for optimizing EHLA process parameters based on coating material behavior and for promoting high-performance, post-heat-treatment-free coatings.
- 9 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessProcess parameter influences on 17-4PH martensitic stainless-steel coatings produced by extreme high-speed laser cladding (EHLA)
Achieving high-performance coatings in the as-built condition, without the need for subsequent heat treatment, is an important and increasingly relevant objective in metallic materials manufacturing, particularly for protective metallic coatings. In this study, defect-free 17-4PH stainless-steel coatings were fabricated using Extreme High-Speed Laser Cladding (EHLA). By tailoring the laser processing parameters, nearly fully martensitic microstructures were obtained in the as-built state. Detailed analysis revealed two distinct dilution mechanisms: diffusion-controlled bonding at the coating–substrate interface and convection- induced dilution of chromium within the coating interior, which the latter is of critical importance to the corrosion resistance of stainless-steel coatings. Furthermore, phase transformation kinetics were simulated using the temperature histories derived from process modeling. The results indicate that the thermal cycles experienced by tracks whose peak temperatures fall within the austenite stability range play a critical role in determining the final phase constitution of the coating. Together, these findings provide key insights for optimizing EHLA process parameters based on coating material behavior and for promoting high-performance, post-heat-treatment-free coatings.
- Open Access
- 27 January 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Investigating the effects of processing head and substrate inclination on the EHLA process: Impact on track formation and surface roughness
Extreme high-speed laser material deposition (EHLA) is a laser-based coating process known for its high deposition rates and excellent resource efficiency. To further increase productivity, higher laser powers and powder feed rates are increasingly used, but this also raises the thermal load on the processing head due to back-reflected radiation. Inclining the processing head or substrate helps deflect this radiation, while also enabling coatings in geometrically constrained areas, such as internal surfaces. However, inclination introduces asymmetries in the powder and laser distribution, potentially affecting track formation and melt pool behavior. This study investigates how inclination between the processing head and a rotationally symmetric substrate influences track geometry, surface quality, dilution, and thermal impact. Two inclination configurations were examined across a range of angles, with systematic variation of feed and rotation direction to simulate pushing and pulling deposition strategies. The results reveal that inclination has a significant and configuration-dependent effect on surface roughness, build-up volume, powder catchment efficiency, and thermal penetration. Variations in asymmetry orientation relative to the motion direction lead to measurable differences in coating properties. The findings offer new insights into optimizing EHLA process parameters for inclined setups, contributing to more robust and application-specific coating strategies.
- 27 January 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Open AccessInvestigating the effects of processing head and substrate inclination on the EHLA process: Impact on track formation and surface roughness
Extreme high-speed laser material deposition (EHLA) is a laser-based coating process known for its high deposition rates and excellent resource efficiency. To further increase productivity, higher laser powers and powder feed rates are increasingly used, but this also raises the thermal load on the processing head due to back-reflected radiation. Inclining the processing head or substrate helps deflect this radiation, while also enabling coatings in geometrically constrained areas, such as internal surfaces. However, inclination introduces asymmetries in the powder and laser distribution, potentially affecting track formation and melt pool behavior. This study investigates how inclination between the processing head and a rotationally symmetric substrate influences track geometry, surface quality, dilution, and thermal impact. Two inclination configurations were examined across a range of angles, with systematic variation of feed and rotation direction to simulate pushing and pulling deposition strategies. The results reveal that inclination has a significant and configuration-dependent effect on surface roughness, build-up volume, powder catchment efficiency, and thermal penetration. Variations in asymmetry orientation relative to the motion direction lead to measurable differences in coating properties. The findings offer new insights into optimizing EHLA process parameters for inclined setups, contributing to more robust and application-specific coating strategies.
- Open Access
- 1 January 2020
- Published by Elsevier in SSRN Electronic Journal
Heat Treatment Design for IN718 by Laser Metal Deposition with High Deposition Rates — Modeling, Simulation and Experiments
Laser metal deposited processed Ni-based superalloy IN718 is characterized by elemental micro-segregation, anisotropy and Laves phases due to the rapid solidification and therefore needs homogenization heat treatment to achieve comparable properties of wrought alloys. In this paper, we report simulation based methodology to design heat treatment IN718 in a laser metal deposition process using Thermo-calc. Initially, the finite element modeling simulates the laser melt pool to compute the solidification rate (G) and temperature gradient(R). Then, the primary dendrite arm spacing are computed through Kurz-fisher [20] and Trivedi [14] modeling integrated with FEM solver. Later a DICTRA homogenization model based on the Primary Dendrite Arm Spacing (PDAS) input values computes the homogenization heat treatment time and temperature. The simulated time scales are verified for two different experiments with contrast laser parameters and are found to be in good agreement confirmed with the results from scanning electron microscopy (SEM). Finally a methodology for integrating the process parameter with the heat treatment design is developed, and a heat treatment map for IN718 is generated that can be integrated with a FEM solver first time in Laser metal deposition process.
- 1 January 2020
- Published by Elsevier in SSRN Electronic Journal
Open AccessHeat Treatment Design for IN718 by Laser Metal Deposition with High Deposition Rates — Modeling, Simulation and Experiments
Laser metal deposited processed Ni-based superalloy IN718 is characterized by elemental micro-segregation, anisotropy and Laves phases due to the rapid solidification and therefore needs homogenization heat treatment to achieve comparable properties of wrought alloys. In this paper, we report simulation based methodology to design heat treatment IN718 in a laser metal deposition process using Thermo-calc. Initially, the finite element modeling simulates the laser melt pool to compute the solidification rate (G) and temperature gradient(R). Then, the primary dendrite arm spacing are computed through Kurz-fisher [20] and Trivedi [14] modeling integrated with FEM solver. Later a DICTRA homogenization model based on the Primary Dendrite Arm Spacing (PDAS) input values computes the homogenization heat treatment time and temperature. The simulated time scales are verified for two different experiments with contrast laser parameters and are found to be in good agreement confirmed with the results from scanning electron microscopy (SEM). Finally a methodology for integrating the process parameter with the heat treatment design is developed, and a heat treatment map for IN718 is generated that can be integrated with a FEM solver first time in Laser metal deposition process.