Slimane Khelloufi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Slimane Khelloufi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Abdelmadjid Herbadji
1 shared publication- Abdelmadjid Herbadji
Laboratory of Physical Chemistry of Materials, Faculty of Sciences and Technology, Chadli Bendjedid University, 36000 El Tarf, Algeria
1 shared publication Achref Cherifi
1 shared publicationAdel Aitbara
1 shared publication- Adel Aitbara
Laboratory of Physical Chemistry of Materials, Faculty of Sciences and Technology, Chadli Bendjedid University, El Tarf, Algeria
1 shared publication - Amine Herbadji
Laboratory: Growth and Characterization of New Semiconductors, University of Ferhat Abbas, 19000 Setif, Algeria
1 shared publication
Latest Publications
- 16 October 2026
- Published by Elsevier in Optical Materials
- Vol. 181
Al doping-driven evolution of the structural, electrical, and optical properties in ZnO thin films
- 16 October 2026
- Published by Elsevier in Optical Materials
- Vol. 181
Al doping-driven evolution of the structural, electrical, and optical properties in ZnO thin films
- 3 February 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (3) , 032503
Optimizing the Photocatalytic Performance of n-Type Cu 2 O/FTO Photoanodes by Controlling Electrodeposited Film Thickness
N-Type Cu 2 O is a promising photocatalyst due to its direct bandgap, enabling strong visible-light absorption. When used as a photoelectrode, however, its performance depends critically on film thickness, which must balance light absorption with efficient charge transport. This study systematically optimized the thickness of electrodeposited Cu 2 O films on FTO substrates by varying deposition time from 5 to 40 min. As deposition time increased, the films evolved from pyramidal nanostructures to dense polycrystalline layers, with thicknesses ranging from ~150 nm to ~1200 nm. Thicker films exhibited improved visible-light absorption and a slight bandgap narrowing from 2.35 to 2.25 eV. All samples showed stable anodic photocurrents characteristic of n-type behavior. The highest photocurrent 0.118 mA occurred for the film deposited for 30 min, corresponding to an optimal thickness of ~750 nm. At this thickness, the film effectively absorbs incident photons while still allowing photogenerated carriers to reach the interface before recombining. Beyond this optimal point, photocatalytic activity declined sharply despite continued gains in light absorption, due to the thickness exceeding the charge-carrier diffusion length, which increased recombination and transport resistance. These results highlight the importance of precise thickness control for maximizing Cu 2 O/FTO photoanode efficiency.
- 3 February 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (3) , 032503
Optimizing the Photocatalytic Performance of n-Type Cu 2 O/FTO Photoanodes by Controlling Electrodeposited Film Thickness
N-Type Cu 2 O is a promising photocatalyst due to its direct bandgap, enabling strong visible-light absorption. When used as a photoelectrode, however, its performance depends critically on film thickness, which must balance light absorption with efficient charge transport. This study systematically optimized the thickness of electrodeposited Cu 2 O films on FTO substrates by varying deposition time from 5 to 40 min. As deposition time increased, the films evolved from pyramidal nanostructures to dense polycrystalline layers, with thicknesses ranging from ~150 nm to ~1200 nm. Thicker films exhibited improved visible-light absorption and a slight bandgap narrowing from 2.35 to 2.25 eV. All samples showed stable anodic photocurrents characteristic of n-type behavior. The highest photocurrent 0.118 mA occurred for the film deposited for 30 min, corresponding to an optimal thickness of ~750 nm. At this thickness, the film effectively absorbs incident photons while still allowing photogenerated carriers to reach the interface before recombining. Beyond this optimal point, photocatalytic activity declined sharply despite continued gains in light absorption, due to the thickness exceeding the charge-carrier diffusion length, which increased recombination and transport resistance. These results highlight the importance of precise thickness control for maximizing Cu 2 O/FTO photoanode efficiency.