J. Yu
Research Subjects
J. Yu has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Irina Alekseevna Panchenko
Siberian State Industrial University
2 shared publications - Sergey V. Konovalov
Siberian State Industrial University
2 shared publications - Vladislav K. Drobyshev
Siberian State Industrial University, Novokuznetsk, Russia
2 shared publications - Alexei Alexandrovich Neiman
Institute of Strength Physics and Materials Science, Siberian Branch, Russian Academy of Sciences, Tomsk, Russia
1 shared publication Ltd Weihai Liyu Industrial Co.
1 shared publicationSergey V. Vorobyov
1 shared publication
Latest Publications
- 30 June 2026
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 24 (2)
EVOLUTION OF MECHANICAL PROPERTIES OF MEDIUM-ENTROPY ALLOYS OF THE COCRNBMNNI SYSTEM
Problem Statement (Relevance). The development of new structural materials with an optimal balance of strength and ductility is one of the key challenges of modern materials science. Medium-entropy alloys of the Co-Cr-Ni system are of considerable interest; however, their properties can be further enhanced through microalloying with elements causing significant atomic lattice distortions, such as niobium and manganese. Understanding the influence of such additives on the structure and mechanical behavior is an important scientific task. Objectives. The research is aimed at investigating the possibility of controlling the mechanical properties of medium-entropy alloys of the Co-Cr-Ni system through controlled alloying with small additions of niobium and manganese (2–6 at.%). Methods Applied. Four alloys of the Nb-Mn-Ni-Co-Cr system have been obtained by vacuum casting followed by remelting for homogenization. Mechanical properties have been studied using uniaxial tensile testing at room temperature, as well as micro- and nanoindentation techniques (according to ISO 14577) to determine hardness and elastic modulus. Fractographic analysis of fracture surfaces has been carried out using scanning electron microscopy. Originality. For the first time, the effect of combined alloying with niobium and manganese on the complex mechanical properties of Co-Cr-Ni-based medium-entropy alloys has been systematically studied. Correlations between elemental composition, hardness, tensile strength, and fracture behavior have been established. Result. It has been found that the addition of niobium leads to solid-solution strengthening due to atomic lattice distortions. The highest values of microhardness (140.7 HV), nanohardness (2.29 GPa), and Young’s modulus (156 GPa) have been obtained for the Nb₂Mn₂Ni₃₆Co₄₀Cr₂₀ composition. The maximum ultimate tensile strength (641 MPa) at relatively low hardness has been demonstrated by the Nb₂Mn₂Ni₃₀Co₄₀Cr₂₆ alloy, indicating a favorable combination of strength and ductility. Fractographic analysis has confirmed a predominantly ductile fracture mechanism. Practical Relevance. The obtained results demonstrate that controlled alloying with niobium and manganese is an effective approach for tailoring the strength-ductility balance in medium-entropy alloys, opening prospects for the development of new structural materials with targeted performance characteristics.
- 30 June 2026
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 24 (2)
EVOLUTION OF MECHANICAL PROPERTIES OF MEDIUM-ENTROPY ALLOYS OF THE COCRNBMNNI SYSTEM
Problem Statement (Relevance). The development of new structural materials with an optimal balance of strength and ductility is one of the key challenges of modern materials science. Medium-entropy alloys of the Co-Cr-Ni system are of considerable interest; however, their properties can be further enhanced through microalloying with elements causing significant atomic lattice distortions, such as niobium and manganese. Understanding the influence of such additives on the structure and mechanical behavior is an important scientific task. Objectives. The research is aimed at investigating the possibility of controlling the mechanical properties of medium-entropy alloys of the Co-Cr-Ni system through controlled alloying with small additions of niobium and manganese (2–6 at.%). Methods Applied. Four alloys of the Nb-Mn-Ni-Co-Cr system have been obtained by vacuum casting followed by remelting for homogenization. Mechanical properties have been studied using uniaxial tensile testing at room temperature, as well as micro- and nanoindentation techniques (according to ISO 14577) to determine hardness and elastic modulus. Fractographic analysis of fracture surfaces has been carried out using scanning electron microscopy. Originality. For the first time, the effect of combined alloying with niobium and manganese on the complex mechanical properties of Co-Cr-Ni-based medium-entropy alloys has been systematically studied. Correlations between elemental composition, hardness, tensile strength, and fracture behavior have been established. Result. It has been found that the addition of niobium leads to solid-solution strengthening due to atomic lattice distortions. The highest values of microhardness (140.7 HV), nanohardness (2.29 GPa), and Young’s modulus (156 GPa) have been obtained for the Nb₂Mn₂Ni₃₆Co₄₀Cr₂₀ composition. The maximum ultimate tensile strength (641 MPa) at relatively low hardness has been demonstrated by the Nb₂Mn₂Ni₃₀Co₄₀Cr₂₆ alloy, indicating a favorable combination of strength and ductility. Fractographic analysis has confirmed a predominantly ductile fracture mechanism. Practical Relevance. The obtained results demonstrate that controlled alloying with niobium and manganese is an effective approach for tailoring the strength-ductility balance in medium-entropy alloys, opening prospects for the development of new structural materials with targeted performance characteristics.
- 1 December 2025
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 66 (6) , 393-400
Microstructure and Mechanical Behavior of Co40Cr12Nb2Mn6Ni40 Medium-Entropy Alloy
The microstructural features and mechanical behavior of a Co40Cr12Nb2Mn6Ni40 medium-entropy alloy fabricated by vacuum-induction melting were studied. The microstructural studies by optical and scanning electron microscopies revealed the formation of a dendritic architecture with a dendrite size of 150–250 µm. Energy-dispersive spectroscopy confirmed a uniform Co/Ni ratio of ≈1 : 1 in the matrix and the homogeneous distribution of chromium and manganese throughout the sample volume. The presence of fine Nb-rich intermetallic particles with a niobium content of up to 6 at %, which provide dispersion strengthening of the material, was established. A comprehensive study of the mechanical behavior was carried out by instrumental indentation under loads ranging from 15 to 1000 mN and by uniaxial tensile tests. Nanoindentation revealed a pronounced dependence of hardness and elastic modulus on the applied load: the hardness decreased from 3.21 ± 0.61 GPa to 1.18 ± 0.6 GPa and the elastic modulus decreased from 131.7 ± 44.1 to 44.7 ± 1.4 GPa. The ultimate tensile strength was 486 MPa, with a high elongation to failure of 92.6%. The specimens were found to exhibit a mixed-mode fracture characterized chiefly by a ductile dimpled mechanism of fracture with the presence of isolated regions of transcrystalline cleavage. The size of dimples varied from 3 to 20 µm, with large dimples (10–20 µm) constituting approximately 20% of the total count. Spherical inclusions of up to 5 µm in size, which served as micropore nucleation sites, were detected at the bottom of the large dimples.
- 1 December 2025
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 66 (6) , 393-400
Microstructure and Mechanical Behavior of Co40Cr12Nb2Mn6Ni40 Medium-Entropy Alloy
The microstructural features and mechanical behavior of a Co40Cr12Nb2Mn6Ni40 medium-entropy alloy fabricated by vacuum-induction melting were studied. The microstructural studies by optical and scanning electron microscopies revealed the formation of a dendritic architecture with a dendrite size of 150–250 µm. Energy-dispersive spectroscopy confirmed a uniform Co/Ni ratio of ≈1 : 1 in the matrix and the homogeneous distribution of chromium and manganese throughout the sample volume. The presence of fine Nb-rich intermetallic particles with a niobium content of up to 6 at %, which provide dispersion strengthening of the material, was established. A comprehensive study of the mechanical behavior was carried out by instrumental indentation under loads ranging from 15 to 1000 mN and by uniaxial tensile tests. Nanoindentation revealed a pronounced dependence of hardness and elastic modulus on the applied load: the hardness decreased from 3.21 ± 0.61 GPa to 1.18 ± 0.6 GPa and the elastic modulus decreased from 131.7 ± 44.1 to 44.7 ± 1.4 GPa. The ultimate tensile strength was 486 MPa, with a high elongation to failure of 92.6%. The specimens were found to exhibit a mixed-mode fracture characterized chiefly by a ductile dimpled mechanism of fracture with the presence of isolated regions of transcrystalline cleavage. The size of dimples varied from 3 to 20 µm, with large dimples (10–20 µm) constituting approximately 20% of the total count. Spherical inclusions of up to 5 µm in size, which served as micropore nucleation sites, were detected at the bottom of the large dimples.