SUSana Ullah

Sana Ullah

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sana Ullah has a total of 13 co-authors. Here are the top co-authors by number of shared publications:

  • Asad Ullah

    Department of Mechanical Engineering, University of Engineering and Technology, Mardan, Pakistan

    1 shared publication
  • Asad Ullah

    Department of Mechanical Engineering, University of Engineering and Technology, Mardan 23200, KPK, Pakistan

    1 shared publication
  • Asad Ullah

    Department of Mechanical Engineering University of Engineering and Technology Mardan 23200

    1 shared publication
  • Hasnain Ali Shah

    Department of Mechanical Engineering, University of Engineering and Technology, Mardan 23200, KPK, Pakistan

    1 shared publication
  • M. Danyal Khan

    Department of Mechanical Engineering, University of Engineering and Technology, Mardan, Pakistan

    1 shared publication
  • Mohammad Ali

    Department of Mechanical Engineering, University of Engineering and Technology, Mardan, Pakistan

    1 shared publication

Latest Publications

  • Open Access

    Design and development of IoT based solar power agriculture robot

    by Mohammad Ali, Sana Ullah, Asad Ullah, M. Danyal Khan, Mubasher Hassan

  • Open Access

    Numerical Investigation of Fin-Enhanced Phase Change Material for Advanced Thermal Management of Lithium-Ion Batteries

    by Hasnain Ali Shah, Asad Ullah, Sana Ullah, Umar Abdullah, Muhammad Ali, Shahzad Iqbal, Shehryar Ishaque

    This study presents a numerical investigation of a slit fin-enhanced phase change material (PCM)-based battery thermal management system (BTMS) for an 18650 cylindrical LiNixCoγMnzO2 lithium-ion battery. The proposed design modifies the conventional solid rectangular external fins by introducing four longitudinal slit fins with uniformly distributed rectangular through-thickness slot cutouts along the fin height. This modification increases the PCM-fin interfacial contact area and creates additional natural convective heat dissipation pathways from the PCM region to the ambient environment while maintaining the same BTMS envelope, PCM thickness, fin count, housing geometry, and material selection as the validated rectangular-fin baseline. The lumped-capacitance thermal model was used for battery heat generation, while the enthalpy-porosity approach was employed to model PCM melting. Simulations were performed in ANSYS Fluent 2024/R2 at 1C, 3C, 5C, and 7C discharge rates at an ambient temperature of 308.15 K. Paraffin wax PCM with a latent heat of approximately 240,000 J/kg was used. The rectangular fin model was first validated against the baseline study, achieving an average cell wall temperature error of 1.03% and a maximum error of 1.47% at 5C, while the total temperature and liquid fraction deviations remained below 0.73%, confirming the reliability of the numerical model. Mesh independence and temporal convergence studies further confirmed that the selected 0.50 mm polyhedral mesh and 0.5 s time step provided accurate and stable results. The results demonstrate that the slit fin geometry provides metric-dependent improvements in PCM utilization, thermal protection duration, and high-rate latent-heat activation rates. At 1C, both configurations remained well below the 318.15 K safety threshold, but the slit fin configuration maintained approximately 0.7 K lower total temperature at 2500 s and delayed PCM melting by about 300 s compared with rectangular fins, preserving more latent heat capacity for later thermal loading. At 3C, the slit fin design extended the thermal protection duration from 1650 s to 2500 s, corresponding to a 51.5% improvement, and increased PCM latent heat utilization from LF = 0.42 to LF = 0.49, representing a 16.7% increase. At 5C, slit fins initiated PCM melting approximately 3.5 times earlier, around 100 s, compared with 350–400 s for rectangular fins, and reached LF = 0.50 at 620 s, whereas rectangular fins reached only LF = 0.37 at 1480 s. This corresponds to approximately 2.87 times faster PCM utilization and 35.1% greater PCM melting. At 7C, the slit fin system again showed stronger PCM engagement, corresponding to 35.7% greater PCM utilization. Temperature and liquid fraction contours confirmed that the slit openings intensify localised PCM melting near the heat source, improve heat spreading through the PCM domain, and support natural convection-assisted melting. Overall, the slit-fin geometry provides a geometry-based enhancement for PCM utilization and thermal protection without changing system size or material selection for PCM-based BTMSs, improving latent heat utilization and thermal protection without increasing system size, PCM volume, or material complexity.


  • Design and Development of a Low Cost Semi-Automated Battery-Powered Egg Incubator with Temperature and Humidity Control

    by Sana Ullah, Asad Ullah, Muhammad Hashir, Muhammad Huzaifa

    Artificial egg incubation is important in poultry production as it controls the environmental factors on the development of embryos. Effective incubation requires a certain level of control over temperature, humidity, ventilation and egg turning. In this paper, the design and development of a semi-automated egg incubator with low cost but with standard incubation parameters mentioned in the existing literature is provided, and a dual-power (AC/DC) operating system is proposed as one of the changes. To assess experimentally, three temperature conditions were taken collectedly, i.e. T1 = 36.5 °C, T2 = 37.5 °C, and T3 = 38 °C and humidity and ventilation conditions maintained fixed. A W1209 thermostat was used to control temperature, and a water-tray-based approach with the help of forced air circulation was used to control humidity. The proposed system has an automatic inverter and battery backup unlike most of the current incubator designs that only use an AC power supply, allowing a continuous operation during power failures. When chicken eggs were experimentally tested, the hatching rate was approximately 80%. The proposed incubator has good reliability, low cost and high suitability in rural poultry farming and educational purposes.