Yiping Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yiping Yao has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Xuerui Mao
Beijing Institute of Technology
3 shared publications - Dandan Xiao
Beijing Institute of Technology
2 shared publications - Htet Myet Ne Ye
School of Mechatronical Engineering, Beijing Institute of Technology 1 , Beijing 100081
1 shared publication Kwing-So Choi
Faculty of Engineering, University of Nottingham 4 , Nottingham NG7 2RD
1 shared publication- Qiangqiang Sun
University of Nottingham
1 shared publication - Yijun Lu
School of Aerospace Engineering, Beijing Institute of Technology 1 , Beijing 100081
1 shared publication
Latest Publications
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Linear perturbation analysis of flow over a flat plate with an elliptic leading edge
Linear perturbation analysis is used to investigate the impact of leading-edge geometry on disturbance amplification, and a flat plate is adopted to eliminate other geometric factors, e.g., thickness, camber, etc. The two-dimensional (2D) base flow is first examined across a range of Reynolds numbers (Re) and leading-edge aspect ratios (AR). The threshold for the formation of a laminar separation bubble (LSB) on the AR-Re plane is identified, with the critical AR increasing monotonically with Re. At Re=300, the optimal energy gain exhibits two competing branches: a three-dimensional (3D) steady branch at inflow frequency ω=0 and finite spanwise wavenumber β, and a 2D unsteady branch at β=0 and finite ω. For higher AR with attached base flow, the dominant response is the 3D steady branch, and its optimal perturbation structure and downstream evolution are consistent with the lift-up mechanism, while finite-frequency responses are weaker. For lower AR with an LSB, the dominant response is the 2D unsteady branch, which exhibits strong finite-frequency amplification over a broad frequency range and downstream wave-packet structures concentrated along the separated shear layer, consistent with Kelvin–Helmholtz instability. A transitional regime is identified near AR≈0.6, where the 3D steady and 2D unsteady branches attain comparable gains, and a 3D unsteady mode with mixed features is observed to be the most energetic one. As Re increases, the crossover between the 2D unsteady and 3D steady branches shifts to lower AR. These results demonstrate that the leading-edge geometry dominates the amplification of free-stream disturbance through its influence on leading-edge separation.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Linear perturbation analysis of flow over a flat plate with an elliptic leading edge
Linear perturbation analysis is used to investigate the impact of leading-edge geometry on disturbance amplification, and a flat plate is adopted to eliminate other geometric factors, e.g., thickness, camber, etc. The two-dimensional (2D) base flow is first examined across a range of Reynolds numbers (Re) and leading-edge aspect ratios (AR). The threshold for the formation of a laminar separation bubble (LSB) on the AR-Re plane is identified, with the critical AR increasing monotonically with Re. At Re=300, the optimal energy gain exhibits two competing branches: a three-dimensional (3D) steady branch at inflow frequency ω=0 and finite spanwise wavenumber β, and a 2D unsteady branch at β=0 and finite ω. For higher AR with attached base flow, the dominant response is the 3D steady branch, and its optimal perturbation structure and downstream evolution are consistent with the lift-up mechanism, while finite-frequency responses are weaker. For lower AR with an LSB, the dominant response is the 2D unsteady branch, which exhibits strong finite-frequency amplification over a broad frequency range and downstream wave-packet structures concentrated along the separated shear layer, consistent with Kelvin–Helmholtz instability. A transitional regime is identified near AR≈0.6, where the 3D steady and 2D unsteady branches attain comparable gains, and a 3D unsteady mode with mixed features is observed to be the most energetic one. As Re increases, the crossover between the 2D unsteady and 3D steady branches shifts to lower AR. These results demonstrate that the leading-edge geometry dominates the amplification of free-stream disturbance through its influence on leading-edge separation.
- 29 July 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1040, A11
Optimal free-stream perturbation to an airfoil flow
Free-stream perturbations induce large coherent structures, crucial to the laminar–turbulent transition on flight vehicles and turbine blades, significantly affecting drag, heat transfer, noise, etc. This paper computes the optimal free-stream perturbations that undergo the strongest amplification using an adjoint method, specifically for the incompressible flow around a NACA0012 airfoil, in contrast to sharp (or no) leading-edge configurations. These perturbations are examined at different angles of attack (0 Superscript ring $^{\circ }$ – 6 Superscript ring $6^{\circ }$ ) and Reynolds numbers ( italic Re equals 1000 ${\textit{Re}} = 1000$ – 8000 $8000$ ). At low angles of attack, two extreme points of energy growth emerge in the frequency–spanwise wavenumber plane, both on the axes. One has a spanwise wavenumber of zero, corresponding to two-dimensional unsteady modes in the wake, and the other has a frequency of zero, representing three-dimensional steady boundary-layer modes. The former is driven by the inflection point of the base velocity profile in the wake and is stronger, whereas the latter is related to the lift-up non-modal stability mechanism and directly influences the flow on the airfoil surfaces. The distribution of the three-dimensional steady optimal perturbations, similarly to the thickness of the base flow boundary layer, follows a italic Re Superscript negative 0.5 ${\textit{Re}}^{-0.5}$ scaling law. This scaling enables the projection of optimal profiles obtained at low italic Re ${\textit{Re}}$ to high ones for engineering applications, where the direct calculation is prohibitively expensive. Subsequently, the linear optimal perturbation at italic Re equals 100 000 ${\textit{Re}} = 100\,000$ is obtained, and the generation, nonlinear deformation and breakdown of streaks are examined by direct numerical simulation to illustrate the impact of the inflow perturbations on transition.- 29 July 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1040, A11
Optimal free-stream perturbation to an airfoil flow
Free-stream perturbations induce large coherent structures, crucial to the laminar–turbulent transition on flight vehicles and turbine blades, significantly affecting drag, heat transfer, noise, etc. This paper computes the optimal free-stream perturbations that undergo the strongest amplification using an adjoint method, specifically for the incompressible flow around a NACA0012 airfoil, in contrast to sharp (or no) leading-edge configurations. These perturbations are examined at different angles of attack (0 Superscript ring $^{\circ }$ – 6 Superscript ring $6^{\circ }$ ) and Reynolds numbers ( italic Re equals 1000 ${\textit{Re}} = 1000$ – 8000 $8000$ ). At low angles of attack, two extreme points of energy growth emerge in the frequency–spanwise wavenumber plane, both on the axes. One has a spanwise wavenumber of zero, corresponding to two-dimensional unsteady modes in the wake, and the other has a frequency of zero, representing three-dimensional steady boundary-layer modes. The former is driven by the inflection point of the base velocity profile in the wake and is stronger, whereas the latter is related to the lift-up non-modal stability mechanism and directly influences the flow on the airfoil surfaces. The distribution of the three-dimensional steady optimal perturbations, similarly to the thickness of the base flow boundary layer, follows a italic Re Superscript negative 0.5 ${\textit{Re}}^{-0.5}$ scaling law. This scaling enables the projection of optimal profiles obtained at low italic Re ${\textit{Re}}$ to high ones for engineering applications, where the direct calculation is prohibitively expensive. Subsequently, the linear optimal perturbation at italic Re equals 100 000 ${\textit{Re}} = 100\,000$ is obtained, and the generation, nonlinear deformation and breakdown of streaks are examined by direct numerical simulation to illustrate the impact of the inflow perturbations on transition.- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Joint control of icing and flow separation using co-flow jet
During climbing and descending, an aircraft operates at high angles of attack, where the boundary layer is prone to separation, resulting in increased drag and reduced lift. Additionally, these scenarios involve a high risk of ice accretion. These challenges highlight the need for an integrated control strategy capable of simultaneously addressing aerodynamic performance degradation and anti-icing requirements, both of which depend on modulating surface flow conditions. In this work, a Co-Flow Jet (CFJ) technique is proposed as a novel strategy for concurrently suppressing flow separation and mitigating ice accretion. Simulations demonstrate that the CFJ effectively introduces suction forces near the upper trailing edge, eliminating separation in this region. Meanwhile, the two-slot leading-edge blowing produces turbulent jets, generating a bubble and virtual surfaces for anti-icing around the lower leading edge and three-dimensional vortical structures around the upper leading edge. These structures reduce the pressure on the upper leading edge, enhancing lift and reducing drag, while also altering water droplet trajectories and impingement dynamics, thereby limiting ice accumulation on the upper surface. Overall, the findings indicate that the CFJ concept offers a promising pathway toward integrating aerodynamic performance enhancement with robust anti-icing capability under high-angle-of-attack conditions.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Joint control of icing and flow separation using co-flow jet
During climbing and descending, an aircraft operates at high angles of attack, where the boundary layer is prone to separation, resulting in increased drag and reduced lift. Additionally, these scenarios involve a high risk of ice accretion. These challenges highlight the need for an integrated control strategy capable of simultaneously addressing aerodynamic performance degradation and anti-icing requirements, both of which depend on modulating surface flow conditions. In this work, a Co-Flow Jet (CFJ) technique is proposed as a novel strategy for concurrently suppressing flow separation and mitigating ice accretion. Simulations demonstrate that the CFJ effectively introduces suction forces near the upper trailing edge, eliminating separation in this region. Meanwhile, the two-slot leading-edge blowing produces turbulent jets, generating a bubble and virtual surfaces for anti-icing around the lower leading edge and three-dimensional vortical structures around the upper leading edge. These structures reduce the pressure on the upper leading edge, enhancing lift and reducing drag, while also altering water droplet trajectories and impingement dynamics, thereby limiting ice accumulation on the upper surface. Overall, the findings indicate that the CFJ concept offers a promising pathway toward integrating aerodynamic performance enhancement with robust anti-icing capability under high-angle-of-attack conditions.