Ahmed E. Abu El-Maaty
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ahmed E. Abu El-Maaty has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Rached Ben-Mansour
KFUPM
2 shared publications- Ahmed S. Alsaman
Interdisciplinary Research Center for Sustainable Energy Systems (IRC-SES), King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia
1 shared publication - Ehab S. Ali
Interdisciplinary Research Center for Sustainable Energy Systems, KFUPM, Dhahran, Saudi Arabia
1 shared publication Hazem K. Abdallah
Mechanical Engineering Department, KFUPM, Dhahran, Saudi Arabia
1 shared publication- Rached Ben-Mansour
Department of Mechanical Engineering, King Fahd University of Petroleum and Minerals, Dhahran 31261, Saudi Arabia
1 shared publication - Ridha Ben Mansour
Interdisciplinary Research Center for Sustainable Energy Systems (IRC-SES), King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia
1 shared publication
Latest Publications
- 2 August 2026
- Published by Springer Nature
- p. 241-248
Sustainable Waste-Heat Recovery for Trucks: CFD Investigation of a Modified Adsorption Bed Using MOF-303
- 2 August 2026
- Published by Springer Nature
- p. 241-248
Sustainable Waste-Heat Recovery for Trucks: CFD Investigation of a Modified Adsorption Bed Using MOF-303
- 8 July 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (15) , 12359-12373
Numerical investigation of the impact of coating thickness and air gaps on cooling adsorption performance
- 8 July 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (15) , 12359-12373
Numerical investigation of the impact of coating thickness and air gaps on cooling adsorption performance
- Open Access
High-Productivity Hybrid Adsorption Desalination Using a Sodium Polyacrylate/CaCl2 Composite with Dual Ejectors and Humidification–Dehumidification Under Saudi Arabian Climate Conditions
This study investigates the utilization of a sodium polyacrylate (SP)/CaCl2 composite as an adsorbent in a low-grade-heat desalination configuration designed for Saudi Arabian conditions. A dynamic system model was developed and validated for an adsorption desalination (AD) cycle integrated with a dual-ejector and a humidification–dehumidification (HDH) unit. Two operating modes were evaluated, including a production-oriented configuration that applies internal evaporator–condenser heat recovery (HR) when no cooling effect is required. Without HR, the AD–EJ–HDH system achieves 41–56 m3/ton·day SDWP and 2.6–2.9 GOR, with a freshwater cost of 1.8–2.4 $/m3 under solar driving and 0.70–0.90 $/m3 under waste heat. With HR, performance increases to SDWP 95–155 m3/ton·day and GOR 2.9–3.1, while costs decrease to about 1.34 $/m3 (solar) and 0.38 $/m3 (waste heat) in June. The SP/CaCl2 composite yields about 85% higher freshwater production than silica gel in the same system, highlighting the material’s potential for high-output hybrid adsorption desalination in hot-climate regions.
Open AccessHigh-Productivity Hybrid Adsorption Desalination Using a Sodium Polyacrylate/CaCl2 Composite with Dual Ejectors and Humidification–Dehumidification Under Saudi Arabian Climate Conditions
This study investigates the utilization of a sodium polyacrylate (SP)/CaCl2 composite as an adsorbent in a low-grade-heat desalination configuration designed for Saudi Arabian conditions. A dynamic system model was developed and validated for an adsorption desalination (AD) cycle integrated with a dual-ejector and a humidification–dehumidification (HDH) unit. Two operating modes were evaluated, including a production-oriented configuration that applies internal evaporator–condenser heat recovery (HR) when no cooling effect is required. Without HR, the AD–EJ–HDH system achieves 41–56 m3/ton·day SDWP and 2.6–2.9 GOR, with a freshwater cost of 1.8–2.4 $/m3 under solar driving and 0.70–0.90 $/m3 under waste heat. With HR, performance increases to SDWP 95–155 m3/ton·day and GOR 2.9–3.1, while costs decrease to about 1.34 $/m3 (solar) and 0.38 $/m3 (waste heat) in June. The SP/CaCl2 composite yields about 85% higher freshwater production than silica gel in the same system, highlighting the material’s potential for high-output hybrid adsorption desalination in hot-climate regions.