Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sai Vempati has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Spectral Entropy and STFT Analysis of Thermal Signatures for Melt Pool Stability in Laser DED Repair of Complex Structures

    by Sai Vempati, Armando José Yáñez Casal, Juan Carlos Becerra Permuy, José Manuel Amado Paz, María José Tobar Vidal

    The influence of internal substrate geometry on thermal stability during Laser Directed Energy Deposition Repair (DED-R) remains insufficiently understood, particularly for components containing internal cavities and cooling channels. This study investigates the thermal response of solid (Alpha), blind-hole (Bravo), and channeled (Charlie) AISI 316L substrates using dual infrared thermography, transient finite element modeling, and Short-Time Fourier Transform (STFT)-frequency-domain analysis. Despite substantial differences in internal heat-dissipation pathways, all substrate configurations exhibited similar peak surface temperatures (~1700–2100 °C), indicating that conventional temperature monitoring alone is insufficient to distinguish geometry-dependent melt-pool behavior. To address this limitation, a Spectral Entropy Index (SEI) derived from STFT analysis was proposed to quantify thermal stability. The channeled substrate exhibited the lowest entropy value (Hs = 0.172), compared with the solid (Hs = 0.181) and blind-hole (Hs = 0.183) configurations, indicating a more ordered and predictable thermal response. Furthermore, distinct variations in the spectral stability shadow revealed geometry-dependent oscillatory behavior that was not observable from thermal histories. Finite element simulations showed good agreement with experimental measurements in conduction-dominated regions (RMSE ≈ 46 °C), whereas deviations were observed within the melt-pool region (~250–310 °C), highlighting the increasing influence of fluid-flow phenomena not captured by the conduction-based model. The results demonstrate that internal substrate architecture primarily influences melt-pool stability through frequency-domain thermodynamics rather than significant changes in peak temperature. The proposed STFT method provides a quantitative approach for monitoring thermal stability and assessing the feasibility of L-DED repair over complex internal geometries.


  • Open Access

    Comparative Microstructural and Mechanical Assessment of Wire vs. Powder Laser-DED (AISI 316L)

    by Sai Vempati, Fabian Riss, Daniel Schlemmer, Ali Aourdou, María José Tobar Vidal, Olexiy Shynkarenko, Armando José Yáñez Casal

    Laser-directed energy deposition (DED) using wire or powder feedstock is a promising way to fabricate prototypes in rapid time, including complex metal parts for advanced engineering applications. In this work, AISI 316L stainless steel—a well-known, weldable alloy model—was used to perform a foundational comparative study of wire-fed (LW-DED) and powder-fed (LP-DED) processes, establishing a baseline before progressing to high-temperature alloys. Hollow cylindrical specimens were fabricated and characterized microstructurally and mechanically. LP-DED produced a refined cellular–dendritic structure with primary dendrite arm spacing of 3.29 ± 0.49 µm and slightly higher average hardness (226 ± 8 HV0.2), accompanied by fine, spherical porosity inherent to the powder feedstock. LW-DED generated coarser epitaxial columnar dendrites (5.15 ± 0.69 µm) and slightly lower hardness (206 ± 10 HV0.2) but achieved nearly full density and high material catching efficiency. The results indicate that both methods yield comparable deposits when parameters are controlled, with LP-DED offering enhanced microstructural refinement and LW-DED providing faster deposition and higher build volume. These findings provide practical guidance for the additive manufacturing of high-performance parts and establish a baseline for the application of DED processes to advanced alloys.


  • Thermo-mechanical analysis of LARES-2 satellite components

    by Sai Vempati, Antonio Paolozzi, Mahender Thotakuri, Sindoni Giampiero, Claudio Paris, Ignazio Ciufolini