Omid Ghorbani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Omid Ghorbani has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Gerhard A. Holzapfel
Institute of Biomechanics, Graz University of Technology, Graz, Austria
3 shared publications - Victorien Prot
Biomechanics, Department of Structural Engineering, The Norwegian University of Science and Technology (NTNU), NO-7491, Trondheim, Norway
2 shared publications Bjørn Skallerud
Department of Structural Engineering Norwegian University of Science and Technology Trondheim Trondheim Norway
1 shared publication- Bjørn Skallerud
Department of Structural Engineering, Norwegian University of Science and Technology, Trondheim, Norway
1 shared publication - Bjørn Skallerud
Department of Structural Engineering, Norwegian University of Science and Technology, Trondheim, 7052, Norway
1 shared publication - Mohammad Javad Sadeghinia
Department of Structural Engineering, Norwegian University of Science and Technology, Trondheim, Norway
1 shared publication
Latest Publications
- Open Access
- 9 July 2026
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 216
Microstructure-Informed Viscoelasticity for the Ascending Thoracic Aortic Wall in the Healthy and Aneurysmal State
- 9 July 2026
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 216
Open AccessMicrostructure-Informed Viscoelasticity for the Ascending Thoracic Aortic Wall in the Healthy and Aneurysmal State
- 5 June 2026
- Published by Wiley in International Journal for Numerical Methods in Biomedical Engineering
- Vol. 42 (6) , e70186
Influence of Fiber Dispersion Representation on the Accuracy of the Mechanical Response of Healthy and Aneurysmal Aortic Wall Tissue
This study investigates the influence of fiber dispersion representation on the accuracy of the mechanical response of anisotropic hyperelastic material models for healthy and aneurysmal human aortic wall tissue under planar biaxial loading. Five fitting strategies were compared: (i) detailed integration of fiber orientation and dispersion data across the thickness; (ii) a single, thickness‐averaged fiber distribution; (iii) two representative layers (media and adventitia); (iv) multiple layers discretized in the radial direction; and (v) a single layer with a symmetrical in‐plane distribution of collagen fibers. The goodness of fit was calculated using the coefficient of determination averaged over all experimental tests. The most accurate fits were achieved with strategy (i), with a goodness of fit for the combined cohort of aneurysm patients and the healthy cohort; comparable accuracy was achieved by the two‐layer model (iii), , but with significantly less complexity in model implementation. As a secondary objective of this study, regional parameters that correlate with the two‐layer model (iii) and are intended for finite element analyses are presented. The method using a symmetrical single layer in model (v) yielded the lowest accuracy, , and highlighted the need to capture non‐symmetric fiber families. The modeling of elastin as a separate anisotropic material was also investigated by comparing two different constitutive modeling approaches. While the healthy cohort showed the best fit by including elastin in model (i) (), separate treatment of elastin in the combined cohorts resulted in only a slight increase of of . This marginal improvement is offset by the risk of overfitting due to additional parameters, which supports the inclusion of elastin in the ground matrix.
- 5 June 2026
- Published by Wiley in International Journal for Numerical Methods in Biomedical Engineering
- Vol. 42 (6) , e70186
Influence of Fiber Dispersion Representation on the Accuracy of the Mechanical Response of Healthy and Aneurysmal Aortic Wall Tissue
This study investigates the influence of fiber dispersion representation on the accuracy of the mechanical response of anisotropic hyperelastic material models for healthy and aneurysmal human aortic wall tissue under planar biaxial loading. Five fitting strategies were compared: (i) detailed integration of fiber orientation and dispersion data across the thickness; (ii) a single, thickness‐averaged fiber distribution; (iii) two representative layers (media and adventitia); (iv) multiple layers discretized in the radial direction; and (v) a single layer with a symmetrical in‐plane distribution of collagen fibers. The goodness of fit was calculated using the coefficient of determination averaged over all experimental tests. The most accurate fits were achieved with strategy (i), with a goodness of fit for the combined cohort of aneurysm patients and the healthy cohort; comparable accuracy was achieved by the two‐layer model (iii), , but with significantly less complexity in model implementation. As a secondary objective of this study, regional parameters that correlate with the two‐layer model (iii) and are intended for finite element analyses are presented. The method using a symmetrical single layer in model (v) yielded the lowest accuracy, , and highlighted the need to capture non‐symmetric fiber families. The modeling of elastin as a separate anisotropic material was also investigated by comparing two different constitutive modeling approaches. While the healthy cohort showed the best fit by including elastin in model (i) (), separate treatment of elastin in the combined cohorts resulted in only a slight increase of of . This marginal improvement is offset by the risk of overfitting due to additional parameters, which supports the inclusion of elastin in the ground matrix.
- Open Access
- 19 February 2026
- Published by Elsevier in Acta Biomaterialia
- Vol. 213, 356-385
Regional mechanical and microstructural variations in ascending thoracic aortic aneurysms influenced by tricuspid and bicuspid aortic valves
- 19 February 2026
- Published by Elsevier in Acta Biomaterialia
- Vol. 213, 356-385
Open AccessRegional mechanical and microstructural variations in ascending thoracic aortic aneurysms influenced by tricuspid and bicuspid aortic valves