MMMaria Cristina Maltarello

Maria Cristina Maltarello

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Maria Cristina Maltarello has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • NANOMECHANICAL CHARACTERIZATION OF ZIRCONIA THIN FILMS DEPOSITED ON UHMWPE BY PULSED PLASMA DEPOSITION

    by Michele Bianchi, Marco Boi, Nicola Lopomo, Maria Cristina Maltarello, Fabiola Liscio, Silvia Milita, Andrea Visani, Alessandro Russo, Maurilio Marcacci

    Plastic deformation and wear of the ultra-high molecular weight polyethylene (UHMWPE) insert have been pointed out as major issues relating to the long-term stability of an orthopaedic implant. The deposition of protective hard, tough and well-adhered zirconia ( ZrO2) thin films directly on the surface of the UHMWPE component via the Pulsed Plasma Deposition (PPD) technique has been already demonstrated to be a feasible way to approach this problem. In the current study, the tribo-mechanical properties of ZrO2-coated UHMWPE with respect to pristine UHMWPE were investigated in detail. Specifically, strength to local plastic deformation, indentation work portioning and creep behavior were evaluated through nanoindentation and micro-scratch tests. Further, preliminary wear data (i.e., rate and volume) were obtained by tribology tests mating coated and pristine UHMWPE with an alumina ball under dry conditions. The results of the mechanical tests evidenced a strong reduction of plastic deformation under both normal and tangential local loads and a drop of the 80% of the creep phenomenon for coated UHMWPE compared to pristine UHMWPE. Despite tribological tests showed similar wear data for coated and pristine UHMWPE, a different wear mechanism was detected between the two groups. The reported results supported the possibility to pursue this novel approach of depositing ZrO2thin film to protect the UHWMPE insert and enhance the long-term stability of the orthopaedic implants.


  • Open Access

    Three‐dimensional cellular distribution in polymeric scaffolds for bone regeneration: a microCT analysis compared to SEM, CLSM and DNA content

    by A. Parrilli, S. Pagani, M. C. Maltarello, S. Santi, A. Salerno, P. A. Netti, R. Giardino, L. Rimondini, M. Fini

    Summary: In orthopaedic surgery the tissues damaged by injury or disease could be replaced using constructs based on biocompatible materials, cells and growth factors. Scaffold design, porosity and early colonization are key components for the implant success. From biological point of view, attention may be also given to the number, type and size of seeded cells, as well as the seeding technique and cell morphological and volumetric alterations. This paper describes the use of the microCT approach (to date used principally for mineralized matrix quantification) to observe construct colonization in terms of cell localization, and make a direct comparison of the microtomographic sections with scanning electron microscopy images and confocal laser scanning microscope analysis. Briefly, polycaprolactone scaffolds were seeded at different cell densities with MG63 osteoblastic‐like cells. Two different endpoints, 1 and 2 weeks, were selected for the three‐dimensional colonization and proliferation analysis of the cells. By observing all images obtained, in addition to a more extensive distribution of cells on scaffolds surfaces than in the deeper layers, cell volume increased at 2 weeks compared to 1 week after seeding. Combining the cell number quantification by deoxyribonucleic acid analysis and the single cell volume changes by confocal laser scanning microscope, we validated the microCT segmentation method by finding no statistical differences in the evaluation of the cell volume fraction of the scaffold. Furthermore, the morphological results of this study suggest that an effective scaffold colonization requires a precise balance between different factors, such as number, type and size of seeded cells in addition to scaffold porosity.