Steve Siebeck
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Steve Siebeck has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
B. Wielage
Technische Universität Chemnitz, Institut für Werkstoffwissenschaften und Werkstofftechnik, Professur Werkstofftechnik, Chemnitz
1 shared publication- Daisy Nestler
Department of Lightweight Structures and Polymer Technology, Chemnitz University of Technology, 09107 Chemnitz, Germany
1 shared publication - Guntram Wagner
Chair of Composites and Material Compounds, Chemnitz University of Technology, Chemnitz, Germany
1 shared publication H. Podlesak
Technische Universität Chemnitz, Institut für Werkstoffwissenschaften und Werkstofftechnik, Professur Werkstofftechnik, Chemnitz
1 shared publicationM. Hockauf
Technische Universität Chemnitz, Institut für Werkstoffwissenschaften und Werkstofftechnik, Professur Werkstofftechnik, Chemnitz
1 shared publication- Maik Trautmann
Group of Composites and Material Compounds (PVW), Institute of Materials Science and Engineering (IWW), Chemnitz University of Technology, 09125 Chemnitz, Germany
1 shared publication
Latest Publications
- Open Access
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Particle-reinforced Aluminum Matrix Composites (AMC) for sustainable lightweight structures: From research to automotive applications
Aluminum matrix composites (AMCs) offer high specific stiffness and strength, making them attractive for lightweight automotive applications. This study investigates AA6082-based AMCs reinforced with SiC for automotive damper systems, using a twin-tube rear-axle damper demonstrator to enable a component-oriented assessment beyond material characterization. Three damper components-an extruded structural tube, a piston rod, and a guide assembly-were manufactured using powder metallurgical routes, including high-energy ball milling, powder extrusion, and field-assisted sintering. The components were characterized regarding microstructure, mechanical performance, surface topography, and tribological behavior and compared with steel components.The results show that extruded AMC tubes exhibit homogeneous microstructures, low anisotropy, and mechanical properties suitable for structural damper components. The guide assembly produced by field-assisted sintering exceeded the specified compressive load and demonstrated reproducible behavior, achieving a mass reduction of up to 66 %. For the piston rod, mass reductions of up to 50 % were achieved; however, maximum bending stress criteria were not fulfilled without system-level modifications. Surface engineering strategies, including coating concepts, were therefore investigated.Overall, the results demonstrate that AMCs should be regarded as multifunctional design materials rather than direct steel substitutes, offering significant potential when component geometry, surface engineering, and system design are adapted concurrently.
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessParticle-reinforced Aluminum Matrix Composites (AMC) for sustainable lightweight structures: From research to automotive applications
Aluminum matrix composites (AMCs) offer high specific stiffness and strength, making them attractive for lightweight automotive applications. This study investigates AA6082-based AMCs reinforced with SiC for automotive damper systems, using a twin-tube rear-axle damper demonstrator to enable a component-oriented assessment beyond material characterization. Three damper components-an extruded structural tube, a piston rod, and a guide assembly-were manufactured using powder metallurgical routes, including high-energy ball milling, powder extrusion, and field-assisted sintering. The components were characterized regarding microstructure, mechanical performance, surface topography, and tribological behavior and compared with steel components.The results show that extruded AMC tubes exhibit homogeneous microstructures, low anisotropy, and mechanical properties suitable for structural damper components. The guide assembly produced by field-assisted sintering exceeded the specified compressive load and demonstrated reproducible behavior, achieving a mass reduction of up to 66 %. For the piston rod, mass reductions of up to 50 % were achieved; however, maximum bending stress criteria were not fulfilled without system-level modifications. Surface engineering strategies, including coating concepts, were therefore investigated.Overall, the results demonstrate that AMCs should be regarded as multifunctional design materials rather than direct steel substitutes, offering significant potential when component geometry, surface engineering, and system design are adapted concurrently.
- 17 September 2010
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 41 (9) , 704-710
Effect of ECAP and heat treatment on microstructure and mechanical properties of a SiC reinforced Al‐Cu alloy
Der Beitrag befasst sich mit der Herstellung und Eigenschaftsmodifizierung eines pulvermetallurgisch hergestellten Verbundwerkstoffes auf Basis der ausscheidungshärtbaren Aluminiumknetlegierung EN AW‐2017 und 5 Vol.‐% SiC‐Partikeln der Kornfraktion 0,2 bis 2 μm. Dabei wird eine Kombination von ECAP und nachträglicher Wärmebehandlung angewendet. Die verschiedenen Behandlungszustände werden anhand von lichtmikroskopischen, raster‐ sowie transmissionselektronenmikroskopischen Untersuchungen charakterisiert. Die mechanischen Eigenschaften werden durch Härtemessungen und quasistatische Zugversuche dokumentiert. Die experimentellen Ergebnisse zeigen, dass mit Hilfe der zur Herstellung verwendeten Prozessroute im stranggepressten Zustand eine relativ homogene Verteilung und eine gute Einbettung der SiC‐Partikel in die Matrix sowie ein geeigneter Grenzflächenzustand erzielt werden. Während der nachträglichen Lösungsglühbehandlung entsteht eine signifikante Porosität, die auf hohe Mengen und unzureichende Entfernung der Stearinsäure (Hilfsstoff bei der Herstellung des Verbundpulvers) zurückzuführen ist. Dadurch werden die mechanischen Eigenschaften des Verbundwerkstoffes negativ beeinflusst. Die Untersuchungen zeigen außerdem, dass die ECAP‐Umformung von Aluminiummatrix‐Verbundwerkstoffen mit max. 1 μm großen Hartstoffpartikeln realisierbar ist und eine Verbesserung der mechanischen Eigenschaften grundsätzlich erzielt werden kann. Die ECAP‐Umformung führt zu einer signifikanten Festigkeitssteigerung, die auf eine veränderte Defektstruktur zurückgeführt werden kann. Die hier betrachtete Temperaturwahl für die nachfolgende Wärmebehandlung bei 170°C erweist sich jedoch als nicht gut geeignet, da ein Entfestigungseffekt der Matrixlegierung aufgrund von Erholungs‐ und Überalterungsvorgängen einsetzte. Die hier präsentierten, ersten Ergebnisse bilden die Grundlage für weitere Untersuchungen zur mikrostrukturellen Optimierung von partikelverstärkten Aluminiumlegierungen durch ECAP.In this study, the production and optimization of an aluminum matrix composite prepared by powder metallurgy, Equal‐channel angular pressing (ECAP) and a subsequent heat treatment is investigated. A gas atomized powder (composition approximately similar to the commercial AA2017 alloy) was high energy ball milled with 5 vol.‐% SiC particles (0.2 to 2 μm), hot iso‐statically pressed and extruded to square bars. Optical, scanning‐ and transmission electron microscopy are performed to characterize the corresponding microstructural evolution. The mechanical properties are determined by quasi‐static tensile testing and hardness measurements. The experimental results show that the extruded condition exhibits a relatively homogeneous particle distribution with a good interface quality. However, the subsequent solid‐solution heat treatment results in a significant increase of porosity due to remnant stearic acid (milling agent for the production of the composite powder) which was only partly removed during degassing. This leads to a significant degradation of the mechanical properties. This study also indicates that ECAP‐processing of aluminum matrix composites with particle sizes below 1 μm can in principle lead to significant increases in strength by altering the relevant defect structures. The heat treatment temperature considered here (170°C) results in a softening due to simultaneous recovery and over‐aging. But the first results presented here may well point out directions for further studies on microstructural optimization of particle reinforced aluminum alloys by ECAP.
- 17 September 2010
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 41 (9) , 704-710
Effect of ECAP and heat treatment on microstructure and mechanical properties of a SiC reinforced Al‐Cu alloy
Der Beitrag befasst sich mit der Herstellung und Eigenschaftsmodifizierung eines pulvermetallurgisch hergestellten Verbundwerkstoffes auf Basis der ausscheidungshärtbaren Aluminiumknetlegierung EN AW‐2017 und 5 Vol.‐% SiC‐Partikeln der Kornfraktion 0,2 bis 2 μm. Dabei wird eine Kombination von ECAP und nachträglicher Wärmebehandlung angewendet. Die verschiedenen Behandlungszustände werden anhand von lichtmikroskopischen, raster‐ sowie transmissionselektronenmikroskopischen Untersuchungen charakterisiert. Die mechanischen Eigenschaften werden durch Härtemessungen und quasistatische Zugversuche dokumentiert. Die experimentellen Ergebnisse zeigen, dass mit Hilfe der zur Herstellung verwendeten Prozessroute im stranggepressten Zustand eine relativ homogene Verteilung und eine gute Einbettung der SiC‐Partikel in die Matrix sowie ein geeigneter Grenzflächenzustand erzielt werden. Während der nachträglichen Lösungsglühbehandlung entsteht eine signifikante Porosität, die auf hohe Mengen und unzureichende Entfernung der Stearinsäure (Hilfsstoff bei der Herstellung des Verbundpulvers) zurückzuführen ist. Dadurch werden die mechanischen Eigenschaften des Verbundwerkstoffes negativ beeinflusst. Die Untersuchungen zeigen außerdem, dass die ECAP‐Umformung von Aluminiummatrix‐Verbundwerkstoffen mit max. 1 μm großen Hartstoffpartikeln realisierbar ist und eine Verbesserung der mechanischen Eigenschaften grundsätzlich erzielt werden kann. Die ECAP‐Umformung führt zu einer signifikanten Festigkeitssteigerung, die auf eine veränderte Defektstruktur zurückgeführt werden kann. Die hier betrachtete Temperaturwahl für die nachfolgende Wärmebehandlung bei 170°C erweist sich jedoch als nicht gut geeignet, da ein Entfestigungseffekt der Matrixlegierung aufgrund von Erholungs‐ und Überalterungsvorgängen einsetzte. Die hier präsentierten, ersten Ergebnisse bilden die Grundlage für weitere Untersuchungen zur mikrostrukturellen Optimierung von partikelverstärkten Aluminiumlegierungen durch ECAP.In this study, the production and optimization of an aluminum matrix composite prepared by powder metallurgy, Equal‐channel angular pressing (ECAP) and a subsequent heat treatment is investigated. A gas atomized powder (composition approximately similar to the commercial AA2017 alloy) was high energy ball milled with 5 vol.‐% SiC particles (0.2 to 2 μm), hot iso‐statically pressed and extruded to square bars. Optical, scanning‐ and transmission electron microscopy are performed to characterize the corresponding microstructural evolution. The mechanical properties are determined by quasi‐static tensile testing and hardness measurements. The experimental results show that the extruded condition exhibits a relatively homogeneous particle distribution with a good interface quality. However, the subsequent solid‐solution heat treatment results in a significant increase of porosity due to remnant stearic acid (milling agent for the production of the composite powder) which was only partly removed during degassing. This leads to a significant degradation of the mechanical properties. This study also indicates that ECAP‐processing of aluminum matrix composites with particle sizes below 1 μm can in principle lead to significant increases in strength by altering the relevant defect structures. The heat treatment temperature considered here (170°C) results in a softening due to simultaneous recovery and over‐aging. But the first results presented here may well point out directions for further studies on microstructural optimization of particle reinforced aluminum alloys by ECAP.