Vladyslav Kostiuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vladyslav Kostiuk has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Jan Fuzer
Institute of Physics, Pavol Jozef Šafárik University in Košice
1 shared publication Ján Fuzer
1 shared publicationMária Fáberová
1 shared publication- Mária Fáberová
Institute of Materials Research, Slovak Academy of Sciences
1 shared publication Peter Kollár
1 shared publication- Peter Kollár
Institute of Physics, Pavol Jozef Šafárik University in Košice
1 shared publication
Latest Publications
- 11 October 2026
- Published by European Powder Metallurgy Association
Effect Of Biotite Content And Processing Parameters On Powder Morphology And Pressability Of Fe|biotite Soft Magnetic Composites
Soft magnetic composites (SMCs) based on iron powders require electrically insulating phases to reduce eddy current losses and enable operation at elevated frequencies. Among various insulating additives, biotite remains relatively underexplored despite its favorable properties. As a mica-group mineral, biotite offers a lamellar structure, high thermal stability, and the potential to act as a dry lubricant during compaction.This study investigates Fe|biotite powder systems and corresponding compacts with a focus on powder preparation and compaction behavior. Atomized iron powder ABC 100.30 with particle size above 45 µm was used as the base material. Iron powders were mixed with 1–5 wt.% biotite using a resonant acoustic mixer (LabRAM) for 15 minute and 24 hour. Compaction was carried out by hydraulic pressing at pressures up to 2000 MPa. The results confirm the potential of Fe|biotite systems for further development of SMCs.
- 11 October 2026
- Published by European Powder Metallurgy Association
Effect Of Biotite Content And Processing Parameters On Powder Morphology And Pressability Of Fe|biotite Soft Magnetic Composites
Soft magnetic composites (SMCs) based on iron powders require electrically insulating phases to reduce eddy current losses and enable operation at elevated frequencies. Among various insulating additives, biotite remains relatively underexplored despite its favorable properties. As a mica-group mineral, biotite offers a lamellar structure, high thermal stability, and the potential to act as a dry lubricant during compaction.This study investigates Fe|biotite powder systems and corresponding compacts with a focus on powder preparation and compaction behavior. Atomized iron powder ABC 100.30 with particle size above 45 µm was used as the base material. Iron powders were mixed with 1–5 wt.% biotite using a resonant acoustic mixer (LabRAM) for 15 minute and 24 hour. Compaction was carried out by hydraulic pressing at pressures up to 2000 MPa. The results confirm the potential of Fe|biotite systems for further development of SMCs.
- 19 February 2026
- Published by SAGE Publications in Powder Metallurgy
- Vol. 69 (3) , 215-228
Deformation structure and magnetic properties of iron powder core compacted at high pressure
This study investigates how compaction pressure and die shape influence the density distribution and related magnetic and electrical properties of pure iron based green compacts. By combining empirical densification models with geometry-specific corrections for wall friction and shear deformation, numerical simulations were conducted for three die types: cylindrical, prismatic, and ring. The simulations predict spatial variations in densification that align with experimental observations from optical microscopy. Results show that high compaction pressures (up to 2500 MPa) can enhance magnetic performance by increasing density and reducing porosity, but they also cause significant inhomogeneities, especially in cylindrical shapes, due to stress localisation near die walls. Ring-shaped compacts demonstrate better uniformity in both density and magnetic properties, confirming the importance of geometry-dependent modelling of compaction. Surface flash formation and grain deformation at the die–punch interface align with shear-enhanced densification zones forecasted by the model. Overall, the findings emphasise the need to consider both friction and shear effects when designing powder metallurgy processes for soft magnetic materials.
- 19 February 2026
- Published by SAGE Publications in Powder Metallurgy
- Vol. 69 (3) , 215-228
Deformation structure and magnetic properties of iron powder core compacted at high pressure
This study investigates how compaction pressure and die shape influence the density distribution and related magnetic and electrical properties of pure iron based green compacts. By combining empirical densification models with geometry-specific corrections for wall friction and shear deformation, numerical simulations were conducted for three die types: cylindrical, prismatic, and ring. The simulations predict spatial variations in densification that align with experimental observations from optical microscopy. Results show that high compaction pressures (up to 2500 MPa) can enhance magnetic performance by increasing density and reducing porosity, but they also cause significant inhomogeneities, especially in cylindrical shapes, due to stress localisation near die walls. Ring-shaped compacts demonstrate better uniformity in both density and magnetic properties, confirming the importance of geometry-dependent modelling of compaction. Surface flash formation and grain deformation at the die–punch interface align with shear-enhanced densification zones forecasted by the model. Overall, the findings emphasise the need to consider both friction and shear effects when designing powder metallurgy processes for soft magnetic materials.