Finn‐Lennard Janthur
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Finn‐Lennard Janthur has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Jörg Hermsdorf
Laser Zentrum Hannover e.V.
5 shared publications - Christian Klose
Institut für Werkstoffkunde (Materials Science), Leibniz University Hannover, Garbsen, Germany
4 shared publications - Hans Jürgen Maier
Leibniz Universität Hannover
4 shared publications - Ludger Overmeyer
Institute of Transport and Automation Technology, Leibniz University Hannover, Garbsen, Germany
4 shared publications Sarah Seffer
4 shared publications- Timon Steinhoff
Leibniz University Hannover
4 shared publications
Latest Publications
- Open Access
- 18 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12)
Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The molecular dynamics (MD) method is employed to investigate the Al/Cu wetting system at the atomistic level. Wetting experiments in an oxygen‐free atmosphere, limited to the fast spreading regime, are used for validation in this study and show good agreement. Several key parameters, including the size of the Al droplet, the temperature of the Al/Cu system, and the crystal orientation of the Cu substrate, are analyzed in detail. The contact angle and equilibrium spreading radius of the Al droplet are used to characterize its wettability and spreading kinetics. The results reveal that: (1) the size of the Al droplet has almost no influence on the equilibrium contact angle once it exceeds a critical value; (2) Higher temperatures promote the wettability of the Al/Cu system, leading to a better droplet spreading; (3) The Al droplet exhibits superior wettability on the Cu(111) surface due to its lowest energy barrier, i.e., the minimum energy an atom must overcome to move. The spreading of Al droplets on all Cu substrates primarily follows a two‐stage process, with an initial fast regime driven by inertia and a subsequent slow regime governed by surface tension (on Cu(100) and Cu(110)) or diffusion (on Cu(111)).
- 18 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12)
Open AccessInvestigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The molecular dynamics (MD) method is employed to investigate the Al/Cu wetting system at the atomistic level. Wetting experiments in an oxygen‐free atmosphere, limited to the fast spreading regime, are used for validation in this study and show good agreement. Several key parameters, including the size of the Al droplet, the temperature of the Al/Cu system, and the crystal orientation of the Cu substrate, are analyzed in detail. The contact angle and equilibrium spreading radius of the Al droplet are used to characterize its wettability and spreading kinetics. The results reveal that: (1) the size of the Al droplet has almost no influence on the equilibrium contact angle once it exceeds a critical value; (2) Higher temperatures promote the wettability of the Al/Cu system, leading to a better droplet spreading; (3) The Al droplet exhibits superior wettability on the Cu(111) surface due to its lowest energy barrier, i.e., the minimum energy an atom must overcome to move. The spreading of Al droplets on all Cu substrates primarily follows a two‐stage process, with an initial fast regime driven by inertia and a subsequent slow regime governed by surface tension (on Cu(100) and Cu(110)) or diffusion (on Cu(111)).
- Open Access
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Nanosecond-Pulsed Laser Ablation as a Universal Method for Oxide Removal and Surface Structuring of Aluminum and Copper for Advanced Manufacturing Applications
Laser surface texturing enables precise control of micro- and nano-scale topographies that govern wettability, adhesion, friction, and interfacial bonding. In this study, nanosecond-pulsed laser ablation under oxygen-free processing conditions is established as a scalable and automation-ready approach for the simultaneous removal of native oxides and the functional texturing of aluminum and copper surfaces for advanced manufacturing applications. By systematically varying pulse overlap, surface morphologies are tuned from isolated ablation craters to homogeneous textures and, at high overlap, to a melt-dominated regime with increased roughness and effective surface area, enabling application-specific tailoring of interfacial properties. Material-dependent near-surface modifications are observed: aluminum exhibits increased hardness and stiffness, while copper shows localized softening, highlighting fundamentally different laser–matter interaction mechanisms relevant for surface engineering. Microstructural evolution and residual stress development depend on overlap and accumulated fluence, with high overlap promoting texture reduction and stress relaxation. X-ray photoelectron spectroscopy confirms effective oxide removal and exposure of metallic copper under oxygen-free conditions, while identical processing in air leads to pronounced reoxidation; aluminum shows the same qualitative trend. The functional relevance of laser-textured, oxide-free surfaces is demonstrated for adhesive bonding, cold roll bonding, compound casting, and laser beam brazing, enabling improved wetting, enhanced interfacial adhesion, reduced critical deformation for solid-state bonding, and flux-free aluminum–copper joining. The results establish oxygen-free ns-pulsed laser ablation as a versatile surface engineering route that integrates cleaning, oxide-removal and functional structuring in a single step, offering broad potential for advanced and automated manufacturing in joining processes.
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNanosecond-Pulsed Laser Ablation as a Universal Method for Oxide Removal and Surface Structuring of Aluminum and Copper for Advanced Manufacturing Applications
Laser surface texturing enables precise control of micro- and nano-scale topographies that govern wettability, adhesion, friction, and interfacial bonding. In this study, nanosecond-pulsed laser ablation under oxygen-free processing conditions is established as a scalable and automation-ready approach for the simultaneous removal of native oxides and the functional texturing of aluminum and copper surfaces for advanced manufacturing applications. By systematically varying pulse overlap, surface morphologies are tuned from isolated ablation craters to homogeneous textures and, at high overlap, to a melt-dominated regime with increased roughness and effective surface area, enabling application-specific tailoring of interfacial properties. Material-dependent near-surface modifications are observed: aluminum exhibits increased hardness and stiffness, while copper shows localized softening, highlighting fundamentally different laser–matter interaction mechanisms relevant for surface engineering. Microstructural evolution and residual stress development depend on overlap and accumulated fluence, with high overlap promoting texture reduction and stress relaxation. X-ray photoelectron spectroscopy confirms effective oxide removal and exposure of metallic copper under oxygen-free conditions, while identical processing in air leads to pronounced reoxidation; aluminum shows the same qualitative trend. The functional relevance of laser-textured, oxide-free surfaces is demonstrated for adhesive bonding, cold roll bonding, compound casting, and laser beam brazing, enabling improved wetting, enhanced interfacial adhesion, reduced critical deformation for solid-state bonding, and flux-free aluminum–copper joining. The results establish oxygen-free ns-pulsed laser ablation as a versatile surface engineering route that integrates cleaning, oxide-removal and functional structuring in a single step, offering broad potential for advanced and automated manufacturing in joining processes.
- Open Access
- 1 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12)
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Surface tension plays a key role in determining melt behavior, wetting, and defect formation in high‐temperature processes such as laser powder bed fusion and wire‐based deposition welding. Accurate surface tension data are therefore essential for optimizing process quality, especially for titanium alloys, like Ti‐6Al‐4V, which are widely used in aerospace and biomedical applications due to their high specific strength and biocompatibility. In this article, the surface tension of Ti‐6Al‐4V is derived from the oscillation of falling droplets using Rayleigh's formula. Conventional levitating droplet techniques for reactive materials require complex evaluation algorithms and specialized hardware to maintain microgravity conditions. In contrast, the presented approach employs only a single high‐speed camera for simultaneous temperature and droplet oscillation measurements, enabling flexible and cost‐effective integration into various technical systems. The method is applied to investigate the influence of residual oxygen on the surface tension by performing experiments in argon and in a monosilane‐doped oxygen‐free atmosphere (−15 ppm O 2 ). The surface tension follows the linear relation γ ( T ) = 1.512 N m −1 − 1.468 × 10 −4 N m −1 K −1 × ( T − 1933 K). No measurable influence of residual oxygen was observed, as the droplet lifetime was four orders of magnitude shorter than the time required for substantial oxygen diffusion.
- 1 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12)
Open AccessSurface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Surface tension plays a key role in determining melt behavior, wetting, and defect formation in high‐temperature processes such as laser powder bed fusion and wire‐based deposition welding. Accurate surface tension data are therefore essential for optimizing process quality, especially for titanium alloys, like Ti‐6Al‐4V, which are widely used in aerospace and biomedical applications due to their high specific strength and biocompatibility. In this article, the surface tension of Ti‐6Al‐4V is derived from the oscillation of falling droplets using Rayleigh's formula. Conventional levitating droplet techniques for reactive materials require complex evaluation algorithms and specialized hardware to maintain microgravity conditions. In contrast, the presented approach employs only a single high‐speed camera for simultaneous temperature and droplet oscillation measurements, enabling flexible and cost‐effective integration into various technical systems. The method is applied to investigate the influence of residual oxygen on the surface tension by performing experiments in argon and in a monosilane‐doped oxygen‐free atmosphere (−15 ppm O 2 ). The surface tension follows the linear relation γ ( T ) = 1.512 N m −1 − 1.468 × 10 −4 N m −1 K −1 × ( T − 1933 K). No measurable influence of residual oxygen was observed, as the droplet lifetime was four orders of magnitude shorter than the time required for substantial oxygen diffusion.
- Open Access
- 23 February 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12) , e202502800
Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity
This work addresses a central challenge in Al–Cu compound casting: native copper oxides, which inhibit wetting and metallurgical bonding. A laser‐based deoxidation strategy (ns‐pulsed, 1064 nm) performed under oxygen‐free, XHV‐equivalent glovebox conditions, and quantifying subsequent oxide regrowth during realistic short‐term handling, is demonstrated. Surface roughness was tuned via pulse/line overlap (0% vs. 70%) and characterized using confocal microscopy and power spectral density analysis. X‐ray photoelectron spectroscopy reveals that laser processing under XHV‐equivalent conditions produces copper surfaces that are more than 98% oxide‐free and remain predominantly metallic for at least 720 h, whereas exposure to ambient air rapidly leads to the formation of a Cu 2 O/Cu(OH) 2 surface layer within 24 h. Subsequent post‐treatment heating promotes the transformation CuO CuO, in accordance with established low‐temperature oxidation pathways. Casting under XHV‐equivalent conditions yields fully bonded Al–Cu interfaces with the expected Al 2 Cu, AlCu, and Al 4 Cu 9 intermetallic layers. Intermetallic compound (IMC) morphology is more strongly governed by processing parameters (temperature, expected melt‐to‐solid ratio, and thermal history) than by minor short‐term oxide regrowth. Overall, laser deoxidation under XHV‐equivalent conditions emerges as a pretreatment that improves wetting, enables controllable IMC formation, and preserves high interfacial thermal conductivity in Al–Cu composite castings.
- 23 February 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12) , e202502800
Open AccessAl–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity
This work addresses a central challenge in Al–Cu compound casting: native copper oxides, which inhibit wetting and metallurgical bonding. A laser‐based deoxidation strategy (ns‐pulsed, 1064 nm) performed under oxygen‐free, XHV‐equivalent glovebox conditions, and quantifying subsequent oxide regrowth during realistic short‐term handling, is demonstrated. Surface roughness was tuned via pulse/line overlap (0% vs. 70%) and characterized using confocal microscopy and power spectral density analysis. X‐ray photoelectron spectroscopy reveals that laser processing under XHV‐equivalent conditions produces copper surfaces that are more than 98% oxide‐free and remain predominantly metallic for at least 720 h, whereas exposure to ambient air rapidly leads to the formation of a Cu 2 O/Cu(OH) 2 surface layer within 24 h. Subsequent post‐treatment heating promotes the transformation CuO CuO, in accordance with established low‐temperature oxidation pathways. Casting under XHV‐equivalent conditions yields fully bonded Al–Cu interfaces with the expected Al 2 Cu, AlCu, and Al 4 Cu 9 intermetallic layers. Intermetallic compound (IMC) morphology is more strongly governed by processing parameters (temperature, expected melt‐to‐solid ratio, and thermal history) than by minor short‐term oxide regrowth. Overall, laser deoxidation under XHV‐equivalent conditions emerges as a pretreatment that improves wetting, enables controllable IMC formation, and preserves high interfacial thermal conductivity in Al–Cu composite castings.