Tushar Batra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tushar Batra has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Arun Kumar Sesham
FREEDM Systems Center, North Carolina State University, Raleigh, USA
1 shared publication- Erik Schaltz
AAU Energy, Aalborg University, 9220 Aalborg, Denmark
1 shared publication Ghanshyam Gohil
FREEDM Systems Center, North Carolina State University, Raleigh, USA
1 shared publication- Nicholas Rodriguez
Materials Engineering Division, Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, CA 94550, USA
1 shared publication - Seungyoung Ahn
Korea Advanced Institute of Science and Technology
1 shared publication - Subhashish Bhattacharya
North Carolina State University
1 shared publication
Latest Publications
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2552-2559
Isolation design considerations for power supply of medium voltage silicon carbide gate drivers
Single switch capable of blocking 10 kV and higher voltages are presently being developed and demand improved gate drivers for their functioning. Induction based gate drivers have been the foremost solutions in this regard. Design challenges that have been outlined for these drivers are low coupling capacitance, strong magnetic coupling and smaller dimensions with isolation not considered in depth. In this paper, first isolation requirements and its physical realization guidelines are provided from IEC 61800-5-1 for electric drives application. Based on study, two system insulation designs: single and double PCB are derived for lower MV and higher MV system respectively. Current loop gate driver with double PCB design is found to be practical and economical solution for higher MV power electronics systems. Afterwards, shortcomings of three state of art induction solutions at both system and magnetic link level is discussed. Improved transformers with primary MV cable providing mandatory solid insulation are fabricated. It is shown through impedance measurements that the cable has negative effect on the magnetizing inductance and coupling capacitance compared to state of art transformer solution. At the end, both set of transformers are tested with 64 kV impulse and 32 kV overvoltage with only improved transformers showing positive results.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2552-2559
Isolation design considerations for power supply of medium voltage silicon carbide gate drivers
Single switch capable of blocking 10 kV and higher voltages are presently being developed and demand improved gate drivers for their functioning. Induction based gate drivers have been the foremost solutions in this regard. Design challenges that have been outlined for these drivers are low coupling capacitance, strong magnetic coupling and smaller dimensions with isolation not considered in depth. In this paper, first isolation requirements and its physical realization guidelines are provided from IEC 61800-5-1 for electric drives application. Based on study, two system insulation designs: single and double PCB are derived for lower MV and higher MV system respectively. Current loop gate driver with double PCB design is found to be practical and economical solution for higher MV power electronics systems. Afterwards, shortcomings of three state of art induction solutions at both system and magnetic link level is discussed. Improved transformers with primary MV cable providing mandatory solid insulation are fabricated. It is shown through impedance measurements that the cable has negative effect on the magnetizing inductance and coupling capacitance compared to state of art transformer solution. At the end, both set of transformers are tested with 64 kV impulse and 32 kV overvoltage with only improved transformers showing positive results.
- 23 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17D517
Effect of ferrite addition above the base ferrite on the coupling factor of wireless power transfer for vehicle applications
Power transfer capability of wireless power transfer systems is highly dependent on the magnetic design of the primary and secondary inductors and is measured quantitatively by the coupling factor. The inductors are designed by placing the coil over a ferrite base to increase the coupling factor and reduce magnetic emissions to the surroundings. Effect of adding extra ferrite above the base ferrite at different physical locations on the self-inductance, mutual inductance, and coupling factor is under investigation in this paper. The addition can increase or decrease the mutual inductance depending on the placement of ferrite. Also, the addition of ferrite increases the self-inductance of the coils, and there is a probability for an overall decrease in the coupling factor. Correct placement of ferrite, on the other hand, can increase the coupling factor relatively higher than the base ferrite as it is closer to the other inductor. Ferrite being a heavy compound of iron increases the inductor weight significantly and needs to be added judiciously. Four zones have been identified in the paper, which shows different sensitivity to addition of ferrite in terms of the two inductances and coupling factor. Simulation and measurement results are presented for different air gaps between the coils and at different gap distances between the ferrite base and added ferrite. This paper is beneficial in improving the coupling factor while adding minimum weight to wireless power transfer system.
- 23 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17D517
Effect of ferrite addition above the base ferrite on the coupling factor of wireless power transfer for vehicle applications
Power transfer capability of wireless power transfer systems is highly dependent on the magnetic design of the primary and secondary inductors and is measured quantitatively by the coupling factor. The inductors are designed by placing the coil over a ferrite base to increase the coupling factor and reduce magnetic emissions to the surroundings. Effect of adding extra ferrite above the base ferrite at different physical locations on the self-inductance, mutual inductance, and coupling factor is under investigation in this paper. The addition can increase or decrease the mutual inductance depending on the placement of ferrite. Also, the addition of ferrite increases the self-inductance of the coils, and there is a probability for an overall decrease in the coupling factor. Correct placement of ferrite, on the other hand, can increase the coupling factor relatively higher than the base ferrite as it is closer to the other inductor. Ferrite being a heavy compound of iron increases the inductor weight significantly and needs to be added judiciously. Four zones have been identified in the paper, which shows different sensitivity to addition of ferrite in terms of the two inductances and coupling factor. Simulation and measurement results are presented for different air gaps between the coils and at different gap distances between the ferrite base and added ferrite. This paper is beneficial in improving the coupling factor while adding minimum weight to wireless power transfer system.