Hairul Nizam Talib
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hairul Nizam Talib has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jurifa Mat Lazi
Universiti Teknikal Malaysia Melaka
2 shared publications Zulkifilie Ibrahim
Universiti Teknikal Malaysia Melaka. (UTeM)
2 shared publications- Ahmad Shukri Abu Hasim
Faculty of Engineering, Universiti Pertahanan Nasional Malaysia, Kuala Lumpur, Malaysia
1 shared publication - Azrita Alias
Universiti Teknikal Malaysia Melaka
1 shared publication Mohamad Syakir Termizi
Department of Power Electronics and Drives, Faculty of Electrical Engineering, Universiti Teknikal Malaysia Melaka (UTeM), Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
1 shared publication- Mohd Junaidi Abdul Aziz
Universiti Teknologi Malaysia
1 shared publication
Latest Publications
- Open Access
- 1 December 2020
- Published by Universitas Ahmad Dahlan in TELKOMNIKA (Telecommunication Computing Electronics and Control)
- Vol. 18 (6) , 3315-3323
High frequency signal injection method for sensorless permanent magnet synchronous motor drives
The objective of this project is to design a high frequency signal injection method for sensorless control of permanent magnet synchronous motor (PMSM) drives. Generally, the PMSM drives control requires the appearance of speed and positon sensor to measure the motor speed hence to feedback the information for variable speed drives operation. The usage of the sensor will increase the size, cost, extra hardwire and feedback devices. Therefore, there is motivation to eliminate this type of sensor by injecting high frequency signal and utilizing the electrical parameter from the motor so that the speed and positon of rotor can be estimated. The proposed position and speed sensorless control method using high frequency signal injection together with all the power electronic circuit are modelled using Simulink. PMSM sensorless driveis simulated and the results are analyzed in terms of speed, torque and stator current response without load disturbance but under the specification of varying speed, forward to reverse operation, reverse to forward operation and step change in reference speed. The results show that the signal injection method performs well during start-up and low speed operation.
- 1 December 2020
- Published by Universitas Ahmad Dahlan in TELKOMNIKA (Telecommunication Computing Electronics and Control)
- Vol. 18 (6) , 3315-3323
Open AccessHigh frequency signal injection method for sensorless permanent magnet synchronous motor drives
The objective of this project is to design a high frequency signal injection method for sensorless control of permanent magnet synchronous motor (PMSM) drives. Generally, the PMSM drives control requires the appearance of speed and positon sensor to measure the motor speed hence to feedback the information for variable speed drives operation. The usage of the sensor will increase the size, cost, extra hardwire and feedback devices. Therefore, there is motivation to eliminate this type of sensor by injecting high frequency signal and utilizing the electrical parameter from the motor so that the speed and positon of rotor can be estimated. The proposed position and speed sensorless control method using high frequency signal injection together with all the power electronic circuit are modelled using Simulink. PMSM sensorless driveis simulated and the results are analyzed in terms of speed, torque and stator current response without load disturbance but under the specification of varying speed, forward to reverse operation, reverse to forward operation and step change in reference speed. The results show that the signal injection method performs well during start-up and low speed operation.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 145-150
Sensorless PMSM drives using Extended Kalman Filter (EKF)
This project presents a sensorless control method for Permanent Magnet Synchronous Motor (PMSM) drives using Extended Kalman Filter (EKF). The study, design, analysis and modeling have been made in order to obtain an estimator of speed and rotor position. The PMSM drives is mostly used in a lots of automation control field due to its benefit like high density and performance motion control for high speed application and better accuracy. However, the conventional motor drives control requires the mechanical sensor or speed sensor to measure the rotor speed and feed it back to the controller in order to achieve the required speed control. The current issue is the mechanical sensor such as tachometer and encoder that used to measure the quantities speed and rotor position are usually too expensive, decrease the stability of the system and raise the budget. Thus, the sensorless control technique using EKF has been more emphasized now in the research field. The main objective of this project is to model and simulate based on Extended Kalman Filter (EKF) sensorless control for PMSM drives and to analyze the performance of sensorless operation related to the Extended Kalman Filter (EKF) of the PMSM drives in term of speed of the motor, rotor position, current and motor's torque. The simulation is carried out using MATLAB/Simulink to measure the overall motor drives performance. The simulation results show that sensorless PMSM drives using EKF have great efficiency, better accuracy and reliable operation system.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 145-150
Sensorless PMSM drives using Extended Kalman Filter (EKF)
This project presents a sensorless control method for Permanent Magnet Synchronous Motor (PMSM) drives using Extended Kalman Filter (EKF). The study, design, analysis and modeling have been made in order to obtain an estimator of speed and rotor position. The PMSM drives is mostly used in a lots of automation control field due to its benefit like high density and performance motion control for high speed application and better accuracy. However, the conventional motor drives control requires the mechanical sensor or speed sensor to measure the rotor speed and feed it back to the controller in order to achieve the required speed control. The current issue is the mechanical sensor such as tachometer and encoder that used to measure the quantities speed and rotor position are usually too expensive, decrease the stability of the system and raise the budget. Thus, the sensorless control technique using EKF has been more emphasized now in the research field. The main objective of this project is to model and simulate based on Extended Kalman Filter (EKF) sensorless control for PMSM drives and to analyze the performance of sensorless operation related to the Extended Kalman Filter (EKF) of the PMSM drives in term of speed of the motor, rotor position, current and motor's torque. The simulation is carried out using MATLAB/Simulink to measure the overall motor drives performance. The simulation results show that sensorless PMSM drives using EKF have great efficiency, better accuracy and reliable operation system.